//SJH300 [CMD-SigData] 00_00 Command – 00 0: Stop command, 1:Forward command, 2:Reverse command 01_00 Command - 01 Output frequency setting for the standard profile 02_00 Command - 02 Low 32-bit data setting of intelligent terminal state 02_00.00 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [FW] Forward command 02_00.01 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [RV] Reverse command 02_00.02 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF1] Multi-speed 1 02_00.03 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF2] Multi-speed 2 02_00.04 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF3] Multi-speed 3 02_00.05 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF4] Multi-speed 4 02_00.07 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [DB] Dynamic braking 02_00.09 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [2CH] 2-stage adjustable speed 02_00.11 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [FRS] Free-run stop 02_00.12 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [EXP] External trip 02_00.13 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [USP] Unattended start protection 02_00.15 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [SFT] Software lock 02_00.16 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [AT] analog input voltage/current 02_00.18 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [RS] Reset 02_00.20 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [STA] 3-wire Start 02_00.21 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [STP] 3-wire Hold 02_00.22 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [F/R] 3-wire FWD/REV 02_00.27 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [UP] remote control increment speed 02_00.28 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [DWN] remote control decrement speed 02_00.29 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [UDC] remote control clear up/down 02_00.31 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [OPE] Force from operator terminal 02_01 Command - 02 High 32-bit data setting of intelligent terminal state 02_01.00 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF1] Multi-speed bit-level 02_01.01 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF2] Multi-speed bit-level 02_01.02 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF3] Multi-speed bit-level 02_01.03 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF4] Multi-speed bit-level 02_01.04 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF5] Multi-speed bit-level 02_01.05 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF6] Multi-speed bit-level 02_01.06 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF7] Multi-speed bit-level 02_01.07 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [OLR] Overload restriction setting 02_01.14 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [LAC] Linear Accel/decel Cancel 02_01.18 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [MTR1] Motor control 1 02_01.19 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [MTR2] Motor control 2 02_01.20 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [MTR3] Motor control 3 03_00 Command - 03 Output frequency 03_01 Command - 03 Output current 03_02 Command - 03 Direction of rotation 03_04 Command - 03 Intelligent input monitor 03_04.00 Command – 03 Intelligent input terminal: FW terminal 03_04.01 Command – 03 Intelligent input terminal: Terminal 1 03_04.02 Command – 03 Intelligent input terminal: Terminal 2 03_04.03 Command – 03 Intelligent input terminal: Terminal 3 03_04.04 Command – 03 Intelligent input terminal: Terminal 4 03_04.05 Command – 03 Intelligent input terminal: Terminal 5 03_04.06 Command – 03 Intelligent input terminal: Terminal 6 03_04.07 Command – 03 Intelligent input terminal: Terminal 7 03_04.08 Command – 03 Intelligent input terminal: Terminal 8 03_05 Command - 03 Intelligent output monitor 03_05.00 Command – 03 Intelligent output terminal: Alarm terminal 03_05.01 Command – 03 Intelligent output terminal: Terminal 11 03_05.02 Command – 03 Intelligent output terminal: Terminal 12 03_05.03 Command – 03 Intelligent output terminal: Terminal 13 03_05.04 Command – 03 Intelligent output terminal: Terminal 14 03_05.05 Command – 03 Intelligent output terminal: Terminal 15 03_06 Command - 03 Frequency converting monitor 03_08 Command - 03 Output voltage monitor 03_11 Command - 03 Run Mode time monitor 03_12 Command - 03 Power ON time monitor 04_00 Command - 04 Status A 04_01 Command - 04 Status B 04_02 Command - 04 Status C 05_00 Command - 05 Total count 05_01 Command - 05 [Trip 1] Trip factor 05_02 Command - 05 [Trip 1] Inverter Status A 05_03 Command - 05 [Trip 1] Inverter Status B 05_04 Command - 05 [Trip 1] Inverter Status C 05_05 Command - 05 [Trip 1] Output frequency 05_06 Command - 05 [Trip 1] Accumulated Run Mode time 05_07 Command - 05 [Trip 1] Output current 05_08 Command - 05 [Trip 1] Output voltage 05_09 Command - 05 [Trip 1] Power ON timer 05_10 Command - 05 [Trip 2] Trip factor 05_11 Command - 05 [Trip 2] Inverter Status A 05_12 Command - 05 [Trip 2] Inverter Status B 05_13 Command - 05 [Trip 2] Inverter Status C 05_14 Command - 05 [Trip 2] Output frequency 05_15 Command - 05 [Trip 2] Accumulated Run Mode time 05_16 Command - 05 [Trip 2] Output current 05_17 Command - 05 [Trip 2] Output voltage 05_18 Command - 05 [Trip 2] Power ON timer 05_19 Command - 05 [Trip 3] Trip factor 05_20 Command - 05 [Trip 3] Inverter Status A 05_21 Command - 05 [Trip 3] Inverter Status B 05_22 Command - 05 [Trip 3] Inverter Status C 05_23 Command - 05 [Trip 3] Output frequency 05_24 Command - 05 [Trip 3] Accumulated Run Mode time 05_25 Command - 05 [Trip 3] Output current 05_26 Command - 05 [Trip 3] Output voltage 05_27 Command - 05 [Trip 3] Power ON timer 05_28 Command - 05 [Trip 4] Trip factor 05_29 Command - 05 [Trip 4] Inverter Status A 05_30 Command - 05 [Trip 4] Inverter Status B 05_31 Command - 05 [Trip 4] Inverter Status C 05_32 Command - 05 [Trip 4] Output frequency 05_33 Command - 05 [Trip 4] Accumulated Run Mode time 05_34 Command - 05 [Trip 4] Output current 05_35 Command - 05 [Trip 4] Output voltage 05_36 Command - 05 [Trip 4] Power ON timer 05_37 Command - 05 [Trip 5] Trip factor 05_38 Command - 05 [Trip 5] Inverter Status A 05_39 Command - 05 [Trip 5] Inverter Status B 05_40 Command - 05 [Trip 5] Inverter Status C 05_41 Command - 05 [Trip 5] Output frequency 05_42 Command - 05 [Trip 5] Accumulated Run Mode time 05_43 Command - 05 [Trip 5] Output current 05_44 Command - 05 [Trip 5] Output voltage 05_45 Command - 05 [Trip 5] Power ON timer 05_46 Command - 05 [Trip 6] Trip factor 05_47 Command - 05 [Trip 6] Inverter Status A 05_48 Command - 05 [Trip 6] Inverter Status B 05_49 Command - 05 [Trip 6] Inverter Status C 05_50 Command - 05 [Trip 6] Output frequency 05_51 Command - 05 [Trip 6] Accumulated Run Mode time 05_52 Command - 05 [Trip 6] Output current 05_53 Command - 05 [Trip 6] Output voltage 05_54 Command - 05 [Trip 6] Power ON timer 08_00 Command - 08 Initializes the inverter parameters to the factory default values 09_00 Command - 09 Check whether Setting Values can be saved to EEPROM or not 0A_00 Command - 0A Save Setting Values to EEPROM 0B_00 Command - 0B Recalculates internal motor constants 0E_00 Command - 0E Read Output Frequency Setting Value [CMD-SigDataEnd] [F-SigData] F002 Acceleration (1) time setting F202 Acceleration (1) time setting, 2nd motor F302 Acceleration (1) time setting, 3rd motor F402 Acceleration (1) time setting, 4th motor F502 Acceleration (1) time setting, 5th motor F602 Acceleration (1) time setting, 6th motor F702 Acceleration (1) time setting, 7th motor F802 Acceleration (1) time setting, 8th motor F003 Deceleration (1) time setting F203 Deceleration (1) time setting, 2nd motor F303 Deceleration (1) time setting, 3rd motor F403 Deceleration (1) time setting, 4th motor F503 Deceleration (1) time setting, 5th motor F603 Deceleration (1) time setting, 6th motor F703 Deceleration (1) time setting, 7th motor F803 Deceleration (1) time setting, 8th motor F004 Keypad Run key routing [F-SigDataEnd] [A-SigData] A001 Frequency source setting A002 Run command source setting A005 [AT] selection A006 [O2] selection A011 [O]-[L] input active range start frequency A012 [O]-[L] input active range end frequency A013 [O]-[L] input active range start voltage A014 [O]-[L] input active range end voltage A015 [O]-[L] input start frequency enable A016 External frequency filter time const A101 [OI]-[L] input active range start frequency A102 [OI]-[L] input active range end frequency A103 [OI]-[L] input active range start voltage A104 [OI]-[L] input active range end voltage A105 [OI]-[L] input start frequency enable A111 [O2]-[L] input active range start frequency A112 [O2]-[L] input active range end frequency A113 [O2]-[L] input active range start voltage A114 [O2]-[L] input active range end voltage A019 Multi-speed operation selection A020 Multi-speed frequency setting A220 Multi-speed frequency setting, 2nd motor A320 Multi-speed frequency setting, 3rd motor A420 Multi-speed frequency setting, 4th motor A520 Multi-speed frequency setting, 5th motor A620 Multi-speed frequency setting, 6th motor A720 Multi-speed frequency setting, 7th motor A820 Multi-speed frequency setting, 8th motor A021 Multi-speed 1 setting A022 Multi-speed 2 setting A023 Multi-speed 3 setting A024 Multi-speed 4 setting A025 Multi-speed 5 setting A026 Multi-speed 6 setting A027 Multi-speed 7 setting A028 Multi-speed 8 setting A029 Multi-speed 9 setting A030 Multi-speed 10 setting A031 Multi-speed 11 setting A032 Multi-speed 12 setting A033 Multi-speed 13 setting A034 Multi-speed 14 setting A035 Multi-speed 15 setting A042 Manual torque boost value A242 Manual torque boost value, 2nd motor A342 Manual torque boost value, 3rd motor A442 Manual torque boost value, 4th motor A542 Manual torque boost value, 5th motor A642 Manual torque boost value, 6th motor A742 Manual torque boost value, 7th motor A842 Manual torque boost value, 8th motor A043 Manual torque boost frequency adjustment A243 Manual torque boost frequency adjustment, 2nd motor A343 Manual torque boost frequency adjustment, 3rd motor A443 Manual torque boost frequency adjustment, 4th motor A543 Manual torque boost frequency adjustment, 5th motor A643 Manual torque boost frequency adjustment, 6th motor A743 Manual torque boost frequency adjustment, 7th motor A843 Manual torque boost frequency adjustment, 8th motor A044 V/F characteristic curve selection, 1st motor A244 V/F characteristic curve selection, 2nd motor A344 V/F characteristic curve selection, 3rd motor A444 V/F characteristic curve selection, 4th motor A544 V/F characteristic curve selection, 5th motor A644 V/F characteristic curve selection, 6th motor A744 V/F characteristic curve selection, 7th motor A844 V/F characteristic curve selection, 8th motor A045 V/F gain setting A051 DC braking enable A052 DC braking frequency setting A053 DC braking wait time A054 DC braking force during deceleration A055 DC braking time for deceleration A056 DC braking edge or level detection for [DB] input A061 Frequency upper limit setting A261 Frequency upper limit setting, 2nd motor A361 Frequency upper limit setting, 3rd motor A461 Frequency upper limit setting, 4th motor A561 Frequency upper limit setting, 5th motor A661 Frequency upper limit setting, 6th motor A761 Frequency upper limit setting, 7th motor A861 Frequency upper limit setting, 8th motor A062 Frequency lower limit setting A262 Frequency lower limit setting, 2nd motor A362 Frequency lower limit setting, 3rd motor A462 Frequency lower limit setting, 4th motor A562 Frequency lower limit setting, 5th motor A662 Frequency lower limit setting, 6th motor A762 Frequency lower limit setting, 7th motor A862 Frequency lower limit setting, 8th motor A063 Jump (center) frequency (1) setting A064 Jump (hysteresis) frequency width (1) setting A065 Jump (center) frequency (2) setting A066 Jump (hysteresis) frequency width (2) setting A067 Jump (center) frequency (3) setting A068 Jump (hysteresis) frequency width (3) setting A069 Acceleration stop frequency setting A070 Acceleration stop time frequency setting A092 Acceleration (2) time setting A292 Acceleration (2) time setting, 2nd motor A392 Acceleration (2) time setting, 3rd motor A492 Acceleration (2) time setting, 4th motorr A592 Acceleration (2) time setting, 5th motorr A692 Acceleration (2) time setting, 6th motorr A792 Acceleration (2) time setting, 7th motorr A892 Acceleration (2) time setting, 8th motorr A093 Deceleration (2) time settings A293 Deceleration (2) time setting, 2nd motor A393 Deceleration (2) time setting, 3rd motor A493 Deceleration (2) time setting, 4th motor A593 Deceleration (2) time setting, 5th motor A693 Deceleration (2) time setting, 6th motor A793 Deceleration (2) time setting, 7th motor A893 Deceleration (2) time setting, 8th motor A097 Acceleration curve selection A098 Deceleration curve selection A131 Acceleration curve constants setting A132 Deceleration curve constants setting [A-SigDataEnd] [b-SigData] b004 Instantaneous power failure / under-voltage trip alarm enable b006 Phase loss detection enable b012 Electronic thermal setting (calculated within the inverter from current output) b212 Electronic thermal setting (calculated within the inverter from current output), 2nd motor b312 Electronic thermal setting (calculated within the inverter from current output), 3rd motor b412 Electronic thermal setting (calculated within the inverter from current output), 4th motor b512 Electronic thermal setting (calculated within the inverter from current output), 5th motor b612 Electronic thermal setting (calculated within the inverter from current output), 6th motor b712 Electronic thermal setting (calculated within the inverter from current output), 7th motor b812 Electronic thermal setting (calculated within the inverter from current output), 8th motor b013 Electronic thermal characteristic b213 Electronic thermal characteristic, 2nd motor b313 Electronic thermal characteristic, 3rd motor b413 Electronic thermal characteristic, 4th motor b513 Electronic thermal characteristic, 5th motor b613 Electronic thermal characteristic, 6th motor b713 Electronic thermal characteristic, 7th motor b813 Electronic thermal characteristic, 8th motor b015 Free setting electronic thermal frequency (1) b016 Free setting electronic thermal current (1) b017 Free setting electronic thermal frequency (2) b018 Free setting electronic thermal current (2) b019 Free setting electronic thermal frequency (3) b020 Free setting electronic thermal current (3) b021 Overload restriction operation mode b022 Overload restriction setting b023 Deceleration rate at overload restriction b024 Overload restriction operation mode (2) b025 Overload restriction setting (2) b026 Deceleration rate at overload restriction (2) b031 Software lock mode selection b034 Run/power-on warning time b035 Rotational direction restriction b037 Function code display restriction b080 [AM] terminal analog meter adjustment b081 [FM] terminal analog meter adjustment b082 Start frequency adjustment b084 Initialization mode (parameters or trip history) b086 Frequency scaling conversion factor b087 STOP key enable b090 Dynamic braking usage ratio b091 Stop mode selection b092 Cooling fan control b095 Dynamic braking control b096 Dynamic braking activation level b098 Thermistor for thermal protection control b099 Thermal protection level setting [b-SigDataEnd] [C-SigData] C001 Terminal [1] function C002 Terminal [2] function C003 Terminal [3] function C004 Terminal [4] function C005 Terminal [5] function C006 Terminal [6] function C007 Terminal [7] function C008 Terminal [8] function C011 Terminal [1] active state C012 Terminal [2] active state C013 Terminal [3] active state C014 Terminal [4] active state C015 Terminal [5] active state C016 Terminal [6] active state C017 Terminal [7] active state C018 Terminal [8] active state C019 Terminal [FW] active state C021 Terminal [11] function C022 Terminal [12] function C023 Terminal [13] function C024 Terminal [14] function C025 Terminal [15] function C026 Alarm relay terminal function C027 [FM] signal selection C028 [AM] signal selection C029 [AMI] signal selection C031 Terminal [11] active state C032 Terminal [12] active state C033 Terminal [13] active state C034 Terminal [14] active state C035 Terminal [15] active state C036 Alarm relay active state C040 Overload signal output mode C041 Overload level setting C042 Frequency arrival setting for accel C043 Arrival frequency setting for decel C045 Frequency arrival setting for acceleration (2) C046 Frequency arrival setting for deceleration (2) C061 Electronic thermal warning level setting C062 Alarm code output C070 Data command method C071 Communication speed selection C072 Node allocation C073 Communication data length selection C074 Communication parity selection C075 Communication stop bit selection C078 Communication wait time C081 [O] input span calibration C082 [O1] input span calibration C083 [O2] input span calibration C085 Thermistor input tuning C086 [AM] terminal offset tuning C087 [AMI] terminal meter tuning C088 [AMI] terminal offset tuning C091 Debug mode enable C101 Up/Down memory mode selection C102 Reset mode selection C111 Overload setting (2) C121 [O] input zero calibration C122 [OI] input zero calibration C123 [O2] input zero calibration [C-SigDataEnd] [H-SigData] H080 Breaking point frequency setting, 1st motor H280 Breaking point frequency setting, 2nd motor H380 Breaking point frequency setting, 3rd motor H480 Breaking point frequency setting, 4th motor H580 Breaking point frequency setting, 5th motor H680 Breaking point frequency setting, 6th motor H780 Breaking point frequency setting, 7th motor H880 Breaking point frequency setting, 8th motor H081 Breaking point voltage setting, 1st motor H281 Breaking point voltage setting, 2nd motor H381 Breaking point voltage setting, 3rd motor H481 Breaking point voltage setting, 4th motor H581 Breaking point voltage setting, 5th motor H681 Breaking point voltage setting, 6th motor H781 Breaking point voltage setting, 7th motor H881 Breaking point voltage setting, 8th motor H082 End frequency setting, 1st motor H282 End frequency setting, 2nd motor H382 End frequency setting, 3rd motor H482 End frequency setting, 4th motor H582 End frequency setting, 5th motor H682 End frequency setting, 6th motor H782 End frequency setting, 7th motor H882 End frequency setting, 8th motor H083 End voltage setting, 1st motor H283 End voltage setting, 2nd motor H383 End voltage setting, 3rd motor H483 End voltage setting, 4th motor H583 End voltage setting, 5th motor H683 End voltage setting, 6th motor H783 End voltage setting, 7th motor H883 End voltage setting, 8th motor H084 AVR P gain setting, 1st motor H284 AVR P gain setting, 2nd motor H384 AVR P gain setting, 3rd motor H484 AVR P gain setting, 4th motor H584 AVR P gain setting, 5th motor H684 AVR P gain setting, 6th motor H784 AVR P gain setting, 7th motor H884 AVR P gain setting, 8th motor H085 AVR I gain setting, 1st motor H285 AVR I gain setting, 2nd motor H385 AVR I gain setting, 3rd motor H485 AVR I gain setting, 4th motor H585 AVR I gain setting, 5th motor H685 AVR I gain setting, 6th motor H785 AVR I gain setting, 7th motor H885 AVR I gain setting, 8th motor H100 Free-setting V/f frequency (7) H101 Free-setting V/f voltage (7) H102 Free-setting V/f frequency (6) H103 Free-setting V/f voltage (6) H104 Free-setting V/f frequency (5) H105 Free-setting V/f voltage (5) H106 Free-setting V/f frequency (4) H107 Free-setting V/f voltage (4) H108 Free-setting V/f frequency (3) H109 Free-setting V/f voltage (3) H110 Free-setting V/f frequency (6) H111 Free-setting V/f voltage (2) H112 Free-setting V/f frequency (1) H113 Free-setting V/f voltage (1) [H-SigDataEnd] [P-SigData] P001 Operation mode on expansion card 1 error P002 Operation mode on expansion card 2 error P031 Accel/decel time input selection [P-SigDataEnd]