//L300P [CMD-SigData] 00_00 Command – 00 0: Stop command, 1:Forward command, 2:Reverse command 01_00 Command – 01 Output frequency setting for the standard profile 02_00 Command – 02 Low 32-bit data setting of intelligent terminal state 02_00.00 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [FW] Forward command 02_00.01 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [RV] Reverse command 02_00.02 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF1] Multi-speed 1 02_00.03 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF2] Multi-speed 2 02_00.04 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF3] Multi-speed 3 02_00.05 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF4] Multi-speed 4 02_00.06 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [JG] Jog operation 02_00.07 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [DB] Dynamic braking 02_00.08 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [SET] set 2nd motor 02_00.09 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [2CH] 2-stage adjustable speed 02_00.11 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [FRS] Free-run stop 02_00.12 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [EXP] External trip 02_00.13 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [USP] Unattended start protection 02_00.14 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CS] Commercial power change 02_00.15 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [SFT] Software lock 02_00.16 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [AT] analog input voltage/current 02_00.18 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [RS] Reset 02_00.20 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [STA] 3-wire Start 02_00.21 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [ST]P 3-wire Hold 02_00.22 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [F/R] 3-wire FWD/REV 02_00.23 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [PID] PID enable 02_00.24 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [PIDC] PID integrator reset 02_00.27 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [UP] remote control increment speed 02_00.28 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [DWN] remote control decrement speed 02_00.29 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [UDC] remote control clear up/down 02_00.31 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [OPE] Force from operator terminal 02_01 Command – 02 High 32-bit data setting of intelligent terminal state 02_01.00 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF1] Multi-speed bit-level 02_01.01 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF2] Multi-speed bit-level 02_01.02 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF3] Multi-speed bit-level 02_01.03 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF4] Multi-speed bit-level 02_01.04 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF5] Multi-speed bit-level 02_01.05 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF6] Multi-speed bit-level 02_01.06 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF7] Multi-speed bit-level 02_01.07 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [OLR] Overload restriction setting 03_00 Command – 03 Output frequency 03_01 Command – 03 Output current 03_02 Command – 03 Direction of rotation 03_03 Command – 03 PID feedback monitor 03_04 Command – 03 Intelligent input monitor 03_04.00 Command – 03 Intelligent input monitor: Forward input 03_04.01 Command – 03 Intelligent input monitor: Input 1 03_04.02 Command – 03 Intelligent input monitor: Input 2 03_04.03 Command – 03 Intelligent input monitor: Input 3 03_04.04 Command – 03 Intelligent input monitor: Input 4 03_04.05 Command – 03 Intelligent input monitor: Input 5 03_04.06 Command – 03 Intelligent input monitor: Input 6 03_04.07 Command – 03 Intelligent input monitor: Input 7 03_04.08 Command – 03 Intelligent input monitor: Input 8 03_05 Command – 03 Intelligent output monitor 03_05.00 Command – 03 Intelligent output monitor: Alarm relay 03_05.01 Command – 03 Intelligent output monitor: Output 1 03_05.02 Command – 03 Intelligent output monitor: Output 2 03_05.03 Command – 03 Intelligent output monitor: Output 3 03_05.04 Command – 03 Intelligent output monitor: Output 4 03_05.05 Command – 03 Intelligent output monitor: Output 5 03_06 Command – 03 Frequency converting monitor 03_08 Command – 03 Output voltage monitor 03_09 Command – 03 Electric power monitor 03_11 Command – 03 Run Mode time monitor 03_12 Command – 03 Power ON time monitor 04_00 Command – 04 Status A 04_01 Command – 04 Status B 04_02 Command – 04 Status C 05_00 Command – 05 Total count 05_01 Command – 05 [Trip 1] Trip factor 05_02 Command – 05 [Trip 1] Inverter Status A 05_03 Command – 05 [Trip 1] Inverter Status B 05_04 Command – 05 [Trip 1] Inverter Status C 05_05 Command – 05 [Trip 1] Output frequency 05_06 Command – 05 [Trip 1] Accumulated Run Mode time 05_07 Command – 05 [Trip 1] Output current 05_08 Command – 05 [Trip 1] Output voltage 05_09 Command – 05 [Trip 1] Power ON timer 05_10 Command – 05 [Trip 2] Trip factor 05_11 Command – 05 [Trip 2] Inverter Status A 05_12 Command – 05 [Trip 2] Inverter Status B 05_13 Command – 05 [Trip 2] Inverter Status C 05_14 Command – 05 [Trip 2] Output frequency 05_15 Command – 05 [Trip 2] Accumulated Run Mode time 05_16 Command – 05 [Trip 2] Output current 05_17 Command – 05 [Trip 2] Output voltage 05_18 Command – 05 [Trip 2] Power ON timer 05_19 Command – 05 [Trip 3] Trip factor 05_20 Command – 05 [Trip 3] Inverter Status A 05_21 Command – 05 [Trip 3] Inverter Status B 05_22 Command – 05 [Trip 3] Inverter Status C 05_23 Command – 05 [Trip 3] Output frequency 05_24 Command – 05 [Trip 3] Accumulated Run Mode time 05_25 Command – 05 [Trip 3] Output current 05_26 Command – 05 [Trip 3] Output voltage 05_27 Command – 05 [Trip 3] Power ON timer 05_28 Command – 05 [Trip 4] Trip factor 05_29 Command – 05 [Trip 4] Inverter Status A 05_30 Command – 05 [Trip 4] Inverter Status B 05_31 Command – 05 [Trip 4] Inverter Status C 05_32 Command – 05 [Trip 4] Output frequency 05_33 Command – 05 [Trip 4] Accumulated Run Mode time 05_34 Command – 05 [Trip 4] Output current 05_35 Command – 05 [Trip 4] Output voltage 05_36 Command – 05 [Trip 4] Power ON timer 05_37 Command – 05 [Trip 5] Trip factor 05_38 Command – 05 [Trip 5] Inverter Status A 05_39 Command – 05 [Trip 5] Inverter Status B 05_40 Command – 05 [Trip 5] Inverter Status C 05_41 Command – 05 [Trip 5] Output frequency 05_42 Command – 05 [Trip 5] Accumulated Run Mode time 05_43 Command – 05 [Trip 5] Output current 05_44 Command – 05 [Trip 5] Output voltage 05_45 Command – 05 [Trip 5] Power ON timer 05_46 Command – 05 [Trip 6] Trip factor 05_47 Command – 05 [Trip 6] Inverter Status A 05_48 Command – 05 [Trip 6] Inverter Status B 05_49 Command – 05 [Trip 6] Inverter Status C 05_50 Command – 05 [Trip 6] Output frequency 05_51 Command – 05 [Trip 6] Accumulated Run Mode time 05_52 Command – 05 [Trip 6] Output current 05_53 Command – 05 [Trip 6] Output voltage 05_54 Command – 05 [Trip 6] Power ON timer 08_00 Command – 08 Initializes the inverter parameters to the factory default values 09_00 Command – 09 Check whether Setting Values can be saved to EEPROM or not 0A_00 Command – 0A Save Setting Values to EEPROM 0B_00 Command – 0B Recalculates internal motor constants 0E_00 Command – 0E Read Output Frequency Setting Value [CMD-SigDataEnd] [F-SigData] F002 Acceleration (1) time setting F202 Acceleration (1) time setting, 2nd motor F003 Deceleration (1) time setting F203 Deceleration (1) time setting, 2nd motor F004 Keypad Run key routing [F-SigDataEnd] [A-SigData] A001 Frequency source setting A002 Run command source setting A003 Base frequency setting A203 Base frequency setting, 2nd motorr A004 Maximum frequency setting A204 Maximum frequency setting, 2nd motor A005 [AT] selection A006 [O2] selection A011 [O]-[L] input active range start frequency A012 [O]-[L] input active range end frequency A013 [O]-[L] input active range start voltage A014 [O]-[L] input active range end voltage A015 [O]-[L] input start frequency enable A016 External frequency filter time constant A019 Multi-speed operation selection A020 Multi-speed frequency setting A220 Multi-speed frequency setting, 2nd motor A021 Multi-speed 1 setting A022 Multi-speed 2 setting A023 Multi-speed 3 setting A024 Multi-speed 4 setting A025 Multi-speed 5 setting A026 Multi-speed 6 setting A027 Multi-speed 7 setting A028 Multi-speed 8 setting A029 Multi-speed 9 setting A030 Multi-speed 10 setting A031 Multi-speed 11 setting A032 Multi-speed 12 setting A033 Multi-speed 13 setting A034 Multi-speed 14 setting A035 Multi-speed 15 setting A038 Jog frequency setting A039 Jog stop mode A041 Torque boost method selection A241 Torque boost method selection, 2nd motor A042 Manual torque boost value A242 Manual torque boost value, 2nd motor A043 Manual torque boost frequency adjustment A243 Manual torque boost frequency adjustment, 2nd motor A044 V/F characteristic curve selection, 1st motor A244 V/F characteristic curve selection, 2nd motor A045 V/F gain setting A051 DC braking enable A052 DC braking frequency setting A053 DC braking wait time A054 DC braking force during deceleration A055 DC braking time for deceleration A056 DC braking / edge or level detection for [DB] input A057 DC braking force for starting A058 DC braking time for starting A059 DC braking carrier frequency setting A061 Frequency upper limit setting A261 Frequency upper limit setting, 2nd motor A062 Frequency lower limit setting A262 Frequency lower limit setting, 2nd motor A063 Jump (center) frequency setting A064 Jump (hysteresis) frequency width setting A065 Jump (center) frequency setting A066 Jump (hysteresis) frequency width setting A067 Jump (center) frequency setting A068 Jump (hysteresis) frequency width setting A069 Acceleration pause frequency setting A070 Acceleration pause time setting A071 PID Function Enable A072 PID proportional gain A073 PID integral time constant A074 PID derivative time constant A075 PV scale conversion A076 PV source setting A081 AVR function select A082 AVR voltage select A085 Operation mode selection A086 Energy saving mode tuning A092 Acceleration (2) time setting A292 Acceleration (2) time setting, 2nd motor A093 Deceleration (2) time setting A293 Deceleration (2) time setting, 2nd motor A094 Select method to switch to Acc2/Dec2 profile A294 Select method to switch to Acc2/Dec2 profile, 2nd motor A095 Acc1 to Acc2 frequency transition point A295 Acc1 to Acc2 frequency transition point, 2nd motor A096 Dec1 to Dec2 frequency transition point A296 Dec1 to Dec2 frequency transition point, 2nd motor A097 Acceleration curve selection A098 Deceleration curve selection A101 [OI]–[L] input active range start frequency A102 [OI]-[L] input active range end frequency A103 [OI]–[L] input active range start current A104 [OI]–[L] input active range end current A105 [OI]-[L] input start frequency enable A111 [O2]-[L] input active range start frequency A112 [O2]-[L] input active range end frequency A113 [O2]-[L] input active range start voltage A114 [O2]-[L] input active range end voltage A131 Acceleration curve constants setting A132 Deceleration curve constants setting [A-SigDataEnd] [b-SigData] b001 Selection of automaticrestart mode b002 Allowable under-voltage power failure time b003 Retry wait time before motor restart b004 Instantaneous power failure / under-voltage trip alarm enable b005 Number of restart on power failure / under-voltage trip events b006 Phase loss detection enable b007 Restart frequency threshold b012 Level of electronic thermal setting b212 Level of electronic thermal setting, 2nd motor b013 Electronic thermal characteristic b213 Electronic thermal characteristic, 2nd motor b015 Free setting, electronic thermal frequency (1) b016 Free setting, electronic thermal current (1) b017 Free setting, electronic thermal frequency (2) b018 Free setting, electronic thermal current (2) b019 Free setting, electronic thermal frequency (3) b020 Free setting, electronic thermal current (3) b021 Overload restriction operation mode b022 Overload restriction setting b023 Deceleration rate at overload restriction b024 Overload restriction operation mode (2) b025 Overload restriction setting (2) b026 Deceleration rate at overload restriction (2) b031 Software lock mode selection b034 Run/power-on warning time b035 Rotational direction restriction b036 Reduced voltage start selection b037 Function code display restriction b080 [AM] terminal analog meter adjustment b081 [FM] terminal analog meter adjustment b082 Start frequency adjustment b083 Carrier frequency setting b084 Initialization mode (parameters or trip history) b085 Country code for initialization b086 Frequency scaling conversion factor b087 STOP key enable b088 Restart mode after FRS b090 Dynamic braking usage ratio b091 Stop mode selection b092 Cooling fan control b095 Dynamic braking control b096 Dynamic braking activation level b098 Thermistor for thermal protection control b099 Thermal protection level setting b100 Free-setting V/f frequency (1) b101 Free-setting V/f voltage (1) b102 Free-setting V/f frequency (2) b103 Free-setting V/f voltage (2) b104 Free-setting V/f frequency (3) b105 Free-setting V/f voltage (3) b106 Free-setting V/f frequency (4) b107 Free-setting V/f voltage (4) b108 Free-setting V/f frequency (5) b109 Free-setting V/f voltage (5) b110 Free-setting V/f frequency (6) b111 Free-setting V/f voltage (6) b112 Free-setting V/f frequency (7) b113 Free-setting V/f voltage (7) [b-SigDataEnd] [C-SigData] C001 Terminal [1] function C002 Terminal [2] function C003 Terminal [3] function C004 Terminal [4] function C005 Terminal [5] function C011 Terminal [1] active state C012 Terminal [2] active state C013 Terminal [3] active state C014 Terminal [4] active state C015 Terminal [5] active state C019 Terminal [FW] active state C021 Terminal [11] function C022 Terminal [12] function C026 Alarm relay terminal function C027 [FM] signal selection C028 [AM] signal selection C029 [AMI] signal selection C031 Terminal [11] active state C032 Terminal [12] active state C036 Alarm relay terminal active state C040 Overload signal output mode C041 Overload level setting C042 Frequency arrival setting for acceleration C043 Arrival frequency setting for deceleration C044 PID deviation level setting C061 Electronic thermal warning level setting C070 Data command method C071 Communication speed selection C072 Node allocation C073 Communication data length selection C074 Communication parity selection C075 Communication stop bit selection C078 Communication wait time C081 [O] input span calibration C082 [O1] input span calibration C083 [O2] input span calibration C085 Thermistor input tuning C086 [AM] terminal offset tuning C087 [AMI] terminal meter tuning C088 [AMI] terminal offset tuning C091 Debug mode enable C101 Up/Down memory mode selection C102 Reset mode selection C103 Restart mode after reset C121 [O] input zero calibration C122 [O1] input zero calibration C123 [O2] input zero calibration [C-SigDataEnd] [H-SigData] H003 Motor capacity, 1st motor H203 Motor capacity, 2nd motor H004 Motor poles setting, 1st motor H204 Motor poles setting, 2nd motor H006 Motor stabilization constant, 1st motor H206 Motor stabilization constant, 2nd motor [H-SigDataEnd] [P-SigData] P001 Operation mode on expansion card 1 error P002 Operation mode on expansion card 2 error P031 Accel/decel time input selection P044 DeviceNet comm watchdog timer P045 Inverter action on DeviceNet comm error P046 DeviceNet polled I/O: Output instance number P047 DeviceNet polled I/O: Input instance number P048 Inverter action on DeviceNet idle mode P049 Motor poles setting for RPM [P-SigDataEnd]