//SJ700 [CMD-SigData] 00_00 Command – 00 0: Stop command, 1:Forward command, 2:Reverse command 01_00 Command – 01 Output frequency setting for the standard profile 02_00 Command – 02 Low 32-bit data setting of intelligent terminal state 02_00.00 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: FW Forward command 02_00.01 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: RV Reverse command 02_00.02 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: CF1: Multispeed 1 setting 02_00.03 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: CF2: Multispeed 2 setting 02_00.04 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: CF3: Multispeed 3 setting 02_00.05 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: CF4: Multispeed 4 setting 02_00.06 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: JG: Jogging 02_00.07 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: DB: External DC braking 02_00.08 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: SET: Set 2nd motor data 02_00.09 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: 2CH: 2-stage acceleration/deceleration 02_00.11 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: FRS: Free-run stop 02_00.12 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: EXT: External trip 02_00.13 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: USP: Unattended start protection 02_00.14 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: CS: Commercial power source enable 02_00.15 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: SFT: Software lock 02_00.16 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: AT: Analog input voltage/current select 02_00.17 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: SET3: 3rd motor control 02_00.18 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: RS: Reset 02_00.20 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: STA: Starting by 3-wire input 02_00.21 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: STP: Stopping by 3-wire input 02_00.22 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: F/R: Forward/reverse switching by 3-wire input 02_00.23 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: PID: Enabling/disabling PID 02_00.24 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: PIDC: PID reset 02_00.26 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: CAS: Control gain setting 02_00.27 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: UP: Remote control UP function 02_00.28 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: DWN: Remote control DOWN function 02_00.29 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: DDC: Remote control data clearing 02_00.31 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: OPE: Forcible operation 02_01 Command – 02 High 32-bit data setting of intelligent terminal state 02_01.00 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: SF1: Multispeed bit 1 02_01.01 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: SF2: Multispeed bit 2 02_01.02 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: SF3: Multispeed bit 3 02_01.03 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: SF4: Multispeed bit 4 02_01.04 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: SF5: Multispeed bit 5 02_01.05 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: SF6: Multispeed bit 6 02_01.06 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: SF7: Multispeed bit 7 02_01.07 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: OLR: Overload restriction selection 02_01.08 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: TL: Enabling /disabling torque limitation 02_01.09 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: TRQ1: Torque limit selection bit 1 02_01.10 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: TRQ2: Torque limit selection bit 2 02_01.11 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: PPI: P/PI mode selection 02_01.12 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: BOK: Braking confirmation 02_01.13 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: ORT: Orientation 02_01.14 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: LAC: LAD cancellation 02_01.15 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: PCLR: Clearance of position deviation 02_01.16 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: STAT: Pulse train position command input enable 02_01.18 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: ADD: Trigger for frequency addition 02_01.19 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: F-TM: Forcible-terminal operation 02_01.20 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: ATR: Permission of torque command input 02_01.21 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: KHC: Cumulative power clearance 02_01.22 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: SON: Servo On 02_01.23 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: FOC: Forcing 02_01.24 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: MI1: General-purpose input 1 02_01.25 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: MI2: General-purpose input 2 02_01.26 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: MI3: General-purpose input 3 02_01.27 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: MI4: General-purpose input 4 02_01.28 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: MI5: General-purpose input 5 02_01.29 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: MI6: General-purpose input 6 02_01.30 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: MI7: General-purpose input 7 02_01.31 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: MI8: General-purpose input 8 03_00 Command – 03 Output frequency 03_01 Command – 03 Output current 03_02 Command – 03 Direction of rotation 03_03 Command – 03 PID feedback monitor 03_04 Command – 03 Intelligent input monitor 03_04.00 Command – 03 Intelligent input terminal: FW terminal 03_04.01 Command – 03 Intelligent input terminal: Terminal 1 03_04.02 Command – 03 Intelligent input terminal: Terminal 2 03_04.03 Command – 03 Intelligent input terminal: Terminal 3 03_04.04 Command – 03 Intelligent input terminal: Terminal 4 03_04.05 Command – 03 Intelligent input terminal: Terminal 5 03_04.06 Command – 03 Intelligent input terminal: Terminal 6 03_04.07 Command – 03 Intelligent input terminal: Terminal 7 03_04.08 Command – 03 Intelligent input terminal: Terminal 8 03_05 Command – 03 Intelligent output monitor 03_05.00 Command – 03 Intelligent output terminal: Relay terminal 03_05.01 Command – 03 Intelligent output terminal: Terminal 11 03_05.02 Command – 03 Intelligent output terminal: Terminal 12 03_05.03 Command – 03 Intelligent output terminal: Terminal 13 03_05.04 Command – 03 Intelligent output terminal: Terminal 14 03_05.05 Command – 03 Intelligent output terminal: Terminal 15 03_06 Command – 03 Frequency converting monitor 03_07 Command – 03 Output torque monitor 03_08 Command – 03 Output voltage monitor 03_09 Command – 03 Electric power monitor 03_11 Command – 03 Run Mode time monitor 03_12 Command – 03 Power ON time monitor 04_00 Command – 04 Status A 04_01 Command – 04 Status B 04_02 Command – 04 Status C 05_00 Command – 05 Total count 05_01 Command – 05 [Trip 1] Trip factor 05_02 Command – 05 [Trip 1] Inverter Status A 05_03 Command – 05 [Trip 1] Inverter Status B 05_04 Command – 05 [Trip 1] Inverter Status C 05_05 Command – 05 [Trip 1] Output frequency 05_06 Command – 05 [Trip 1] Accumulated Run Mode time 05_07 Command – 05 [Trip 1] Output current 05_08 Command – 05 [Trip 1] Output voltage 05_09 Command – 05 [Trip 1] Power ON timer 05_10 Command – 05 [Trip 2] Trip factor 05_11 Command – 05 [Trip 2] Inverter Status A 05_12 Command – 05 [Trip 2] Inverter Status B 05_13 Command – 05 [Trip 2] Inverter Status C 05_14 Command – 05 [Trip 2] Output frequency 05_15 Command – 05 [Trip 2] Accumulated Run Mode time 05_16 Command – 05 [Trip 2] Output current 05_17 Command – 05 [Trip 2] Output voltage 05_18 Command – 05 [Trip 2] Power ON timer 05_19 Command – 05 [Trip 3] Trip factor 05_20 Command – 05 [Trip 3] Inverter Status A 05_21 Command – 05 [Trip 3] Inverter Status B 05_22 Command – 05 [Trip 3] Inverter Status C 05_23 Command – 05 [Trip 3] Output frequency 05_24 Command – 05 [Trip 3] Accumulated Run Mode time 05_25 Command – 05 [Trip 3] Output current 05_26 Command – 05 [Trip 3] Output voltage 05_27 Command – 05 [Trip 3] Power ON timer 05_28 Command – 05 [Trip 4] Trip factor 05_29 Command – 05 [Trip 4] Inverter Status A 05_30 Command – 05 [Trip 4] Inverter Status B 05_31 Command – 05 [Trip 4] Inverter Status C 05_32 Command – 05 [Trip 4] Output frequency 05_33 Command – 05 [Trip 4] Accumulated Run Mode time 05_34 Command – 05 [Trip 4] Output current 05_35 Command – 05 [Trip 4] Output voltage 05_36 Command – 05 [Trip 4] Power ON timer 05_37 Command – 05 [Trip 5] Trip factor 05_38 Command – 05 [Trip 5] Inverter Status A 05_39 Command – 05 [Trip 5] Inverter Status B 05_40 Command – 05 [Trip 5] Inverter Status C 05_41 Command – 05 [Trip 5] Output frequency 05_42 Command – 05 [Trip 5] Accumulated Run Mode time 05_43 Command – 05 [Trip 5] Output current 05_44 Command – 05 [Trip 5] Output voltage 05_45 Command – 05 [Trip 5] Power ON timer 05_46 Command – 05 [Trip 6] Trip factor 05_47 Command – 05 [Trip 6] Inverter Status A 05_48 Command – 05 [Trip 6] Inverter Status B 05_49 Command – 05 [Trip 6] Inverter Status C 05_50 Command – 05 [Trip 6] Output frequency 05_51 Command – 05 [Trip 6] Accumulated Run Mode time 05_52 Command – 05 [Trip 6] Output current 05_53 Command – 05 [Trip 6] Output voltage 05_54 Command – 05 [Trip 6] Power ON timer 08_00 Command – 08 Initializes the inverter parameters to the factory default values 09_00 Command – 09 Check whether Setting Values can be saved to EEPROM or not 0A_00 Command – 0A Save Setting Values to EEPROM 0B_00 Command – 0B Recalculates internal motor constants 0E_00 Command – 0E Read Output Frequency Setting Value [CMD-SigDataEnd] [F-SigData] F002 Acceleration (1) time setting F202 Acceleration (1) time setting, 2nd motor F302 Acceleration (1) time setting, 3rd motor F003 Deceleration (1) time setting F203 Deceleration (1) time setting, 2nd motor F303 Deceleration (1) time setting, 3rd motor F004 Keypad Run key routing [F-SigDataEnd] [A-SigData] A001 Frequency source setting A002 Run command source setting A003 Base frequency setting A203 Base frequency setting, 2nd motor A303 Base frequency setting, 3rd motor A004 Maximum frequency setting A204 Maximum frequency setting, 2nd motor A304 Maximum frequency setting, 3rd motor A005 [AT] selection A006 [O2] selection A011 [O]-[L] input active range start frequency A012 [O]-[L] input active range end frequency A013 [O]-[L] input active range start voltage A014 [O]-[L] input active range end voltage A015 [O]-[L] input start frequency enable A016 Analog Input filter A017 Simple sequence function selection A019 Multi-speed operation selection A020 Multi-speed frequency setting A220 Multi-speed frequency setting, 2nd motor A320 Multi-speed frequency setting, 3rd motor A021 Multi-speed 1 setting A022 Multi-speed 2 setting A023 Multi-speed 3 setting A024 Multi-speed 4 setting A025 Multi-speed 5 setting A026 Multi-speed 6 setting A027 Multi-speed 7 setting A028 Multi-speed 8 setting A029 Multi-speed 9 setting A030 Multi-speed 10 setting A031 Multi-speed 11 setting A032 Multi-speed 12 setting A033 Multi-speed 13 setting A034 Multi-speed 14 setting A035 Multi-speed 15 setting A038 Jog frequency setting A039 Jog stop mode A041 Torque boost method selection A241 Torque boost method selection, 2nd motor A042 Manual torque boost value A242 Manual torque boost value, 2nd motor A342 Manual torque boost value, 3rd motor A043 Manual torque boost frequency adjustment A243 Manual torque boost frequency adjustment, 2nd motor A343 Manual torque boost frequency adjustment, 3rd motor A044 V/F characteristic curve selection A244 V/F characteristic curve selection, 2nd motor A344 V/F characteristic curve selection, 3rd motor A045 V/F gain setting A046 Automatic torque boost voltage compensation gain A246 Automatic torque boost voltage compensation gain, 2nd motor A047 Automatic torque boost sliding compensation gain A247 Automatic torque boost sliding compensation gain, 2nd motor A051 DC braking enable A052 DC braking frequency setting A053 DC braking wait time A054 DC braking force during deceleration A055 DC braking time for deceleration A056 DC braking edge or level detection for [DB] input A057 DC braking force for starting A058 DC braking time for starting A059 DC braking carrier frequency setting A061 Frequency upper limit setting A261 Frequency upper limit setting, 2nd motor A062 Frequency lower limit setting A262 Frequency lower limit setting, 2nd motor A063 Jump (center) frequency setting A064 Jump (center) frequency width setting A065 Jump (center) frequency setting A066 Jump (center) frequency width setting A067 Jump (center) frequency setting A068 Jump (center) frequency width setting A069 Acceleration stop frequency setting A070 Acceleration stop time frequency setting A071 PID Function Enable A072 PID proportional gain A073 PID integral time constant A074 PID derivative gain A075 PV scale conversion A076 PV source setting A077 PID deviation reverse output A078 PID variable range A081 AVR function select A082 AVR voltage select A085 Operation mode selection A086 Energy saving mode tuning A092 Acceleration(2) time setting A292 Acceleration(2) time setting, 2nd motor A392 Acceleration(2) time setting, 3rd motor A093 Deceleration(2) time setting A293 Deceleration(2) time setting, 2nd motor A393 Deceleration(2) time setting, 3rd motor A094 Select method to switch to Acc2/Dec2 profile A294 Select method to switch to Acc2/Dec2, 2nd motor A095 Acc1 to Acc2 frequency transition point A295 Acc1 to Acc2 frequency transition point , 2nd motor A096 Dec1 to Dec2 frequency transition point A296 Dec1 to Dec2 frequency transition point, 2nd motor A097 Acceleration curve selection A098 Deceleration curve selection A101 [OI]-[L] input active range start frequency A102 [OI]-[L] input active range end frequency A103 [OI]-[L] input active range start curve A104 [OI]-[L] input active range end curve A105 [OI]-[L] input start frequency enable A111 [O2]-[L] input active range start frequency A112 [O2]-[L] input active range end frequency A113 [O2]-[L] input active range start voltage A114 [O2]-[L] input active range end voltage A131 Acceleration curve constants setting A132 Deceleration curve constants setting A141 Operation frequency seletion A142 Operation frequency seletion, 2nd motor A143 Operation function operator seletion A145 Addition frequency setting A146 Addition frequency mark selection A150 EL-S curve ratio setting on acceleration A151 EL-S curve ratio setting on acceleration, 2nd motor A152 EL-S curve ratio setting on deceleration A153 EL-S curve ratio setting on deceleration, 2nd motor [A-SigDataEnd] [b-SigData] b001 Selection of restart mode b002 Allowable under-voltage power failure time b003 Retry wait time before motor restart b004 Instantaneous power failure / under-voltage trip alarm enable b005 Number of restart on power failure / under-voltage trip events b006 Phase loss detection enable b007 Restart frequency threshold b008 Trip retry selection b009 Number of restart on under-voltage b010 Number of restart on over-voltage / over-current b011 Trip retry wait time b012 Electronic thermal setting (calculated within the inverter from current output) b212 Electronic thermal setting (calculated within the inverter from current output), 2nd motor b312 Electronic thermal setting (calculated within the inverter from current output), 3rd motor b013 Electronic thermal characteristic b213 Electronic thermal characteristic, 2nd motor b313 Electronic thermal characteristic, 3rd motor b015 Free setting electronic thermal frequency b016 Free setting electronic thermal current b017 Free setting electronic thermal frequency, 2nd motor b018 Free setting electronic thermal current, 2nd motor b019 Free setting electronic thermal frequency, 3rd motor b020 Free setting electronic thermal current, 3rd motor b021 Overload restriction operation mode b022 Overload restriction setting b023 Deceleration rate at overload restriction b024 Overload restriction operation mode, 2nd motor b025 Overload restriction setting, 2nd motor b026 Deceleration rate at overload restriction, 2nd motor b027 Over-current restriction function selection b028 Frequency gaining over restart level b029 Frequency gaining over restart constants setting b030 Restart frequency constants setting on frequency gaining over restart b031 Software lock mode selection b034 Run/power-on warning time b035 Rotational direction restriction b036 Reduced voltage start selection b037 Function code display restriction b038 Initial screen selection b039 User parameter automatic setting function selection b040 Torque limit selection b041 Torque limit (1) (forward-driving in 4-quadrant mode) b042 Torque limit (2) (reverse-regenerating in 4-quadrant mode) b043 Torque limit (3) (reverse-driving in 4-quadrant mode) b044 Torque limit (4) (forward-regenerating in 4-quadrant mode) b045 Torque limit LADSTOP enable b046 Reverse Run protection enable b050 Controller deceleration and stop on power loss b051 DC bus voltage trigger level during power loss b052 Over-voltage threshold during power loss b053 Deceleration time setting during power loss b054 Initial output frequency decrease during power loss b078 Multiplication power clear b079 Multiplication power display gain b082 Start frequency adjustment b083 Carrier frequency setting b084 Initialization mode (parameters or trip history) b085 Country code for initialization b086 Frequency scaling conversion factor b087 STOP key enable b088 Restart mode after FRS b090 Dynamic braking usage ratio b091 Stop mode selection b092 Cooling fan control b095 Dynamic braking control b096 Dynamic braking activation level b098 Thermistor for thermal protection control b099 Thermal protection level setting b100 Free-setting V/f frequency(1) b101 Free-setting V/f voltage(1) b102 Free-setting V/f frequency(2 b103 Free-setting V/f voltage(2) b104 Free-setting V/f frequency(3) b105 Free-setting V/f voltage(3) b106 Free-setting V/f frequency(4) b107 Free-setting V/f voltage(4) b108 Free-setting V/f frequency(5) b109 Free-setting V/f voltage(5) b110 Free-setting V/f frequency(6) b111 Free-setting V/f voltage(6) b112 Free-setting V/f frequency(7) b113 Free-setting V/f voltage(7) b120 Brake Control Enable b121 Brake Wait Time for Release b122 Brake Wait Time for Acceleration b123 Brake Wait Time for Stopping b124 Brake Wait Time for Confirmation b125 Brake Release Frequency Setting b126 Brake Release Current Setting b127 Brake turning on frequency Setting b130 Over-voltage control function selection b131 Over-voltage control level b132 Over-voltage control constant setting [b-SigDataEnd] [C-SigData] C001 Terminal [1] function C002 Terminal [2] function C003 Terminal [3] function C004 Terminal [4] function C005 Terminal [5] function C006 Terminal [6] function C007 Terminal [7] function C008 Terminal [8] function C011 Terminal [1] active state C012 Terminal [2] active state C013 Terminal [3] active state C014 Terminal [4] active state C015 Terminal [5] active state C016 Terminal [6] active state C017 Terminal [7] active state C018 Terminal [8] active state C019 Terminal [FW] active state C021 Terminal [11] function C022 Terminal [12] function C023 Terminal [13] function C024 Terminal [14] function C025 Terminal [15] function C026 Intelligent relay terminal selection C027 [FM] signal selection C028 [AM] signal selection C029 [AMI] signal selection C030 Digital current monitor standard value C031 Terminal [11] active state C032 Terminal [12] active state C033 Terminal [13] active state C034 Terminal [14] active state C035 Terminal [15] active state C036 Intelligent relay selection C038 Low current signal output mode selection C039 Low current detection level C040 Overload signal output mode C041 Overload level setting C042 Frequency arrival setting for accel C043 Arrival frequency setting for decal C044 PID deviation level setting C045 Frequency arrival setting for acceleration (2) C046 Frequency arrival setting for deceleration (2) C052 PID feedback maximum value setting C053 PID feedback minimum value setting C055 Over-torque (forward-driving) level setting C056 Over-torque (reverse regenerating) level setting C057 Over-torque (reverse driving) level setting C058 Over-torque (forward regenerating) level setting C061 Electronic thermal warning level setting C062 Alarm code output C063 Zero speed detection level C064 Cooling fin overheat level C071 Communication speed selection C072 Node allocation C073 Communication data length selection C074 Communication parity selection C075 Communication stop bit selection C076 Communication error selection C077 Communication trip time C078 Communication wait time C079 Communication method selection C081 [O] input span calibration C082 [OI] input span calibration C083 [O2] input span calibration C085 Thermistor input tuning C091 Debug mode enable C101 Up/Down memory mode selection C102 Reset mode selection C103 Restart mode after reset C105 FM gain setting C106 AM gain setting C107 AMI gain setting C109 AM bias setting C110 AMI bias setting C111 Overload setting (2) C121 [O] input zero calibration C122 [O1] input zero calibration C123 [O2] input zero calibration C130 Output 11 on deLay time C131 Output 11 off deLay time C132 Output 12 on deLay time C133 Output 12 off deLay time C134 Output 13 on deLay time C135 Output 13 off deLay time C136 Output 14 on deLay time C137 Output 14 off deLay time C138 Output 15 on deLay time C139 Output 15 off deLay time C140 Output RY on deLay time C141 Output RY off deLay time C142 Logic output signal 1 selection 1 C143 Logic output signal 1 selection 2 C144 Logical output signal 1 operator selection C145 Logic output signal 2 selection 1 C146 Logic output signal 2 selection 2 C147 Logical output signal 2 operator selection C148 Logic output signal 3 selection 1 C149 Logic output signal 3 selection 2 C150 Logical output signal 3 operator selection C151 Logic output signal 4 selection 1 C152 Logic output signal 4 selection 2 C153 Logical output signal 4 operator selection C154 Logic output signal 5 selection 1 C155 Logic output signal 5 selection 2 C156 Logical output signal 5 operator selection C157 Logic output signal 6 selection 1 C158 Logic output signal 6 selection 2 C159 Logical output signal 6 operator selection [C-SigDataEnd] [H-SigData] H202 Motor data selection, 2nd motor H003 Motor capacity, 1st motor H203 Motor capacity, 2nd motor H004 Motor poles setting, 1st motor H204 Motor poles setting, 2nd motor H005 Motor speed constant, 1st motor H205 Motor speed constant, 2nd motor H006 Motor stabilization constant, 1st motor H206 Motor stabilization constant, 2ndmotor H306 Motor stabilization constant, 3rdmotor H020 Motor constant R1, 1st motor H220 Motor constant R1, 2nd motor H021 Motor constant R2, 1st motor H221 Motor constant R2, 2nd motor H022 Motor constant L, 1st motor H222 Motor constant L, 2nd motor H023 Motor constant Io H223 Motor constant Io, 2nd motor H024 Motor Constant J H224 Motor Constant J, 2nd motor H030 Motor constant R1, 1st motor (Automatic tuning data) H230 Motor constant R1, 2nd motor (Automatic tuning data) H031 Motor constant R2, 1st motor (Automatic tuning data) H231 Motor constant R2, 2nd motor (Automatic tuning data) H032 Motor constant L, 1st motor (Automatic tuning data) H232 Motor constant L, 2nd motor (Automatic tuning data) H033 Motor constant Io (Automatic tuning data) H233 Motor constant Io, 2nd motor (Automatic tuning data) H034 Motor Constant J (Automatic tuning data) H234 Motor Constant J, 2nd motor (Automatic tuning data) H050 PI proportional gain for 1st motor H250 PI proportional gain for 2nd motor H051 PI integral gain for 1st motor H251 PI integral gain for 2nd motor H052 P proportional gain setting for 1st motor H252 P proportional gain setting for 2nd motor H060 Zero LV limit for 1st motor H260 Zero LV limit for 2nd motor H061 Boost quantity on Zero SLV starting for 1st motor H261 Boost quantity on Zero SLV starting for 2nd motor H070 Terminal selection PI proportional gain setting H071 Terminal selection PI integral gain setting H072 Terminal selection P proportional gain setting H073 Gain switching time [H-SigDataEnd] [P-SigData] P001 Operation mode on expansion card 1 error P002 Operation mode on expansion card 2 error P011 Encoder pulse-per-revolution(PPR) setting P012 Control pulse setting P013 Pulse line mode setting P014 Home search stop position setting P015 Home search speed setting P016 Home search direction setting P017 Home search completion range setting P018 Home search completion delay time setting P019 Electronic gear set position selection P020 Electronic gear ratio numerator setting P021 Electronic gear ratio denominator setting P022 Feed-forward gain setting P023 Position loop gain setting P025 Temperature compensation thermistor enable P026 Over-speed error detection level setting P027 Speed deviation error detection level setting P028 Motor gear ratio numerator setting P029 Motor gear ratio denominator setting P031 Accel/decal time input selection P032 Position command input selection P033 Torque command input selection P034 Torque command setting P035 Polarity selection on torque command by 02 P036 Torque bias mode P037 Torque bias value P038 Torque bias polarity selection P039 Torque control time speed limit value (Forward using) P040 Torque control time speed limit value (Reverse using) P044 DeviceNet comm watchdog timer P045 Inverter action on DeviceNet comm error P046 DeviceNet polled I/O: Output instance number P047 DeviceNet polled I/O: Input instance number P048 Inverter action on DeviceNet idle mode P049 Motor poles setting for RPM P055 Pulse line frequency scale P056 Pulse line frequency filter time constant P057 Pulse line bias amount P058 Pulse line limit P100 Simple sequence function user parameter U(00) P101 Simple sequence function user parameter U(01) P102 Simple sequence function user parameter U(02) P103 Simple sequence function user parameter U(03) P104 Simple sequence function user parameter U(04) P105 Simple sequence function user parameter U(05) P106 Simple sequence function user parameter U(06) P107 Simple sequence function user parameter U(07) P108 Simple sequence function user parameter U(08) P109 Simple sequence function user parameter U(09) P110 Simple sequence function user parameter U(10) P111 Simple sequence function user parameter U(11) P112 Simple sequence function user parameter U(12) P113 Simple sequence function user parameter U(13) P114 Simple sequence function user parameter U(14) P115 Simple sequence function user parameter U(15) P116 Simple sequence function user parameter U(16) P117 Simple sequence function user parameter U(17) P118 Simple sequence function user parameter U(18) P119 Simple sequence function user parameter U(19) P120 Simple sequence function user parameter U(20) P121 Simple sequence function user parameter U(21) P122 Simple sequence function user parameter U(22) P123 Simple sequence function user parameter U(23) P124 Simple sequence function user parameter U(24) P125 Simple sequence function user parameter U(25) P126 Simple sequence function user parameter U(26) P127 Simple sequence function user parameter U(27) P128 Simple sequence function user parameter U(28) P129 Simple sequence function user parameter U(29) P130 Simple sequence function user parameter U(30) P131 Simple sequence function user parameter U(31) [P-SigDataEnd]