//SJH300 [CMD-SigData] 00_00 Command – 00 0: Stop command, 1:Forward command, 2:Reverse command 01_00 Command – 01 Output frequency setting for the standard profile 02_00 Command – 02 Low 32-bit data setting of intelligent terminal state 02_00.00 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [FW] Forward command 02_00.01 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [RV] Reverse command 02_00.02 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF1] Multi-speed 1 02_00.03 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF2] Multi-speed 2 02_00.04 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF3] Multi-speed 3 02_00.05 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [CF4] Multi-speed 4 02_00.07 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [DB] Dynamic braking 02_00.09 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [2CH] 2-stage adjustable speed 02_00.11 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [FRS] Free-run stop 02_00.12 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [EXP] External trip 02_00.13 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [USP] Unattended start protection 02_00.15 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [SFT] Software lock 02_00.16 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [AT] analog input voltage/current 02_00.18 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [RS] Reset 02_00.20 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [STA] 3-wire Start 02_00.21 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [STP] 3-wire Hold 02_00.22 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [F/R] 3-wire FWD/REV 02_00.27 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [UP] remote control increment speed 02_00.28 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [DWN] remote control decrement speed 02_00.29 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [UDC] remote control clear up/down 02_00.31 Command – 02 Lower 32 bits of 64-bit Intelligent Terminal Status data: [OPE] Force from operator terminal 02_01 Command – 02 High 32-bit data setting of intelligent terminal state 02_01.00 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF1] Multi-speed bit-level 02_01.01 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF2] Multi-speed bit-level 02_01.02 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF3] Multi-speed bit-level 02_01.03 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF4] Multi-speed bit-level 02_01.04 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF5] Multi-speed bit-level 02_01.05 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF6] Multi-speed bit-level 02_01.06 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SF7] Multi-speed bit-level 02_01.07 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [OLR] Overload restriction setting 02_01.14 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [LAC] Linear Accel/decel Cancel 02_01.18 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SET0] Set 0 bit 02_01.19 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SET1] Set 1 bit 02_01.20 Command – 02 Higher 32 bits of 64-bit Intelligent Terminal Status data: [SET2] Set 2 bit 03_00 Command – 03 Output frequency 03_01 Command – 03 Output current 03_02 Command – 03 Direction of rotation 03_04 Command – 03 Intelligent input monitor 03_04.00 Command – 03 Intelligent input terminal: FW terminal 03_04.01 Command – 03 Intelligent input terminal: Terminal 1 03_04.02 Command – 03 Intelligent input terminal: Terminal 2 03_04.03 Command – 03 Intelligent input terminal: Terminal 3 03_04.04 Command – 03 Intelligent input terminal: Terminal 4 03_04.05 Command – 03 Intelligent input terminal: Terminal 5 03_04.06 Command – 03 Intelligent input terminal: Terminal 6 03_04.07 Command – 03 Intelligent input terminal: Terminal 7 03_04.08 Command – 03 Intelligent input terminal: Terminal 8 03_05 Command – 03 Intelligent output monitor 03_05.00 Command – 03 Intelligent output terminal: Alarm terminal 03_05.01 Command – 03 Intelligent output terminal: Terminal 11 03_05.02 Command – 03 Intelligent output terminal: Terminal 12 03_05.03 Command – 03 Intelligent output terminal: Terminal 13 03_05.04 Command – 03 Intelligent output terminal: Terminal 14 03_05.05 Command – 03 Intelligent output terminal: Terminal 15 03_06 Command – 03 Frequency converting monitor 03_07 Command – 03 Output torque monitor 03_08 Command – 03 Output voltage monitor 03_09 Command – 03 Electric power monitor 03_11 Command – 03 Run Mode time monitor 03_12 Command – 03 Power ON time monitor 04_00 Command – 04 Status A 04_01 Command – 04 Status B 04_02 Command – 04 Status C 05_00 Command – 05 Total count 05_01 Command – 05 [Trip 1] Trip factor 05_02 Command – 05 [Trip 1] Inverter Status A 05_03 Command – 05 [Trip 1] Inverter Status B 05_04 Command – 05 [Trip 1] Inverter Status C 05_05 Command – 05 [Trip 1] Output frequency 05_06 Command – 05 [Trip 1] Accumulated Run Mode time 05_07 Command – 05 [Trip 1] Output current 05_08 Command – 05 [Trip 1] Output voltage 05_09 Command – 05 [Trip 1] Power ON timer 05_10 Command – 05 [Trip 2] Trip factor 05_11 Command – 05 [Trip 2] Inverter Status A 05_12 Command – 05 [Trip 2] Inverter Status B 05_13 Command – 05 [Trip 2] Inverter Status C 05_14 Command – 05 [Trip 2] Output frequency 05_15 Command – 05 [Trip 2] Accumulated Run Mode time 05_16 Command – 05 [Trip 2] Output current 05_17 Command – 05 [Trip 2] Output voltage 05_18 Command – 05 [Trip 2] Power ON timer 05_19 Command – 05 [Trip 3] Trip factor 05_20 Command – 05 [Trip 3] Inverter Status A 05_21 Command – 05 [Trip 3] Inverter Status B 05_22 Command – 05 [Trip 3] Inverter Status C 05_23 Command – 05 [Trip 3] Output frequency 05_24 Command – 05 [Trip 3] Accumulated Run Mode time 05_25 Command – 05 [Trip 3] Output current 05_26 Command – 05 [Trip 3] Output voltage 05_27 Command – 05 [Trip 3] Power ON timer 05_28 Command – 05 [Trip 4] Trip factor 05_29 Command – 05 [Trip 4] Inverter Status A 05_30 Command – 05 [Trip 4] Inverter Status B 05_31 Command – 05 [Trip 4] Inverter Status C 05_32 Command – 05 [Trip 4] Output frequency 05_33 Command – 05 [Trip 4] Accumulated Run Mode time 05_34 Command – 05 [Trip 4] Output current 05_35 Command – 05 [Trip 4] Output voltage 05_36 Command – 05 [Trip 4] Power ON timer 05_37 Command – 05 [Trip 5] Trip factor 05_38 Command – 05 [Trip 5] Inverter Status A 05_39 Command – 05 [Trip 5] Inverter Status B 05_40 Command – 05 [Trip 5] Inverter Status C 05_41 Command – 05 [Trip 5] Output frequency 05_42 Command – 05 [Trip 5] Accumulated Run Mode time 05_43 Command – 05 [Trip 5] Output current 05_44 Command – 05 [Trip 5] Output voltage 05_45 Command – 05 [Trip 5] Power ON timer 05_46 Command – 05 [Trip 6] Trip factor 05_47 Command – 05 [Trip 6] Inverter Status A 05_48 Command – 05 [Trip 6] Inverter Status B 05_49 Command – 05 [Trip 6] Inverter Status C 05_50 Command – 05 [Trip 6] Output frequency 05_51 Command – 05 [Trip 6] Accumulated Run Mode time 05_52 Command – 05 [Trip 6] Output current 05_53 Command – 05 [Trip 6] Output voltage 05_54 Command – 05 [Trip 6] Power ON timer 08_00 Command – 08 Initializes the inverter parameters to the factory default values 09_00 Command – 09 Check whether Setting Values can be saved to EEPROM or not 0A_00 Command – 0A Save Setting Values to EEPROM 0B_00 Command – 0B Recalculates internal motor constants 0E_00 Command – 0E Read Output Frequency Setting Value [CMD-SigDataEnd] [F-SigData] F002 Acceleration (1) time setting F202 Acceleration (1) time setting, 2nd motor F302 Acceleration (1) time setting, 3rd motor F402 Acceleration (1) time setting, 4th motor F502 Acceleration (1) time setting, 5th motor F003 Deceleration (1) time setting F203 Deceleration (1) time setting, 2nd motor F303 Deceleration (1) time setting, 3rd motor F403 Deceleration (1) time setting, 4th motor F503 Deceleration (1) time setting, 5th motor F004 Keypad Run key routing [F-SigDataEnd] [A-SigData] A001 Frequency source setting A002 Run command source setting A003 Base frequency setting A203 Base frequency setting, 2nd motor A303 Base frequency setting, 3rd motor A403 Base frequency setting, 4th motor A503 Base frequency setting, 5th motor A004 Maximum frequency setting A204 Maximum frequency setting, 2nd motor A304 Maximum frequency setting, 3rd motor A404 Maximum frequency setting, 4th motor A504 Maximum frequency setting, 5th motor A005 [AT] selection A006 [O2] selection A011 [O]-[L] input active range start frequency A012 [O]-[L] input active range end frequency A013 [O]-[L] input active range start voltage A014 [O]-[L] input active range end voltage A015 [O]-[L] input start frequency enable A016 External frequency filter time const A019 Multi-speed operation selection A020 Multi-speed frequency setting A220 Multi-speed frequency setting, 2nd motor A320 Multi-speed frequency setting, 3rd motor A420 Multi-speed frequency setting, 4th motor A520 Multi-speed frequency setting, 5th motor A021 Multi-speed 1 setting A022 Multi-speed 2 setting A023 Multi-speed 3 setting A024 Multi-speed 4 setting A025 Multi-speed 5 setting A026 Multi-speed 6 setting A027 Multi-speed 7 setting A028 Multi-speed 8 setting A029 Multi-speed 9 setting A030 Multi-speed 10 setting A031 Multi-speed 11 setting A032 Multi-speed 12 setting A033 Multi-speed 13 setting A034 Multi-speed 14 setting A035 Multi-speed 15 setting A042 Manual torque boost value A242 Manual torque boost value, 2nd motor A342 Manual torque boost value, 3rd motor A442 Manual torque boost value, 4th motor A542 Manual torque boost value, 5th motor A043 Manual torque boost frequency adjustment A243 Manual torque boost frequency adjustment, 2nd motor A343 Manual torque boost frequency adjustment, 3rd motor A443 Manual torque boost frequency adjustment, 4th motor A543 Manual torque boost frequency adjustment, 5th motor A044 V/F characteristic curve selection, 1st motor A244 V/F characteristic curve selection, 2nd motor A344 V/F characteristic curve selection, 3rd motor A444 V/F characteristic curve selection, 4th motor A544 V/F characteristic curve selection, 5th motor A045 V/F gain setting A051 DC braking enable A052 DC braking frequency setting A053 DC braking wait time A054 DC braking force during deceleration A055 DC braking time for deceleration A056 DC braking edge or level detection for [DB] input A057 DC braking force for starting A058 DC braking time for starting A059 DC braking carrier frequency setting A061 Frequency upper limit setting A261 Frequency upper limit setting, 2nd motor A361 Frequency upper limit setting, 3rd motor A461 Frequency upper limit setting, 4th motor A561 Frequency upper limit setting, 5th motor A062 Frequency lower limit setting A262 Frequency lower limit setting, 2nd motor A362 Frequency lower limit setting, 3rd motor A462 Frequency lower limit setting, 4th motor A562 Frequency lower limit setting, 5th motor A063 Jump (center) frequency setting A064 Jump (hysteresis) frequency width setting A065 Jump (center) frequency setting A066 Jump (hysteresis) frequency width setting A067 Jump (center) frequency setting A068 Jump (hysteresis) frequency width setting A069 Acceleration stop frequency setting A070 Acceleration stop time frequency setting A081 AVR function select A082 AVR voltage select A092 Acceleration (2) time setting A292 Acceleration (2) time setting, 2nd motor A392 Acceleration (2) time setting, 3rd motor A492 Acceleration (2) time setting, 4th motorr A592 Acceleration (2) time setting, 5th motorr A093 Deceleration (2) time settings A293 Deceleration (2) time setting, 2nd motor A393 Deceleration (2) time setting, 3rd motor A493 Deceleration (2) time setting, 4th motor A593 Deceleration (2) time setting, 5th motor A094 Select method to switch to Acc2/Dec2 profile A294 Select method to switch to Acc2/Dec2, 2nd motor A394 Select method to switch to Acc2/Dec2, 3rd motor A494 Select method to switch to Acc2/Dec2, 4th motor A594 Select method to switch to Acc2/Dec2, 5th motor A095 Acc1 to Acc2 frequency transition point A295 Acc1 to Acc2 frequency transition point , 2nd motor A395 Acc1 to Acc2 frequency transition point , 3rd motor A495 Acc1 to Acc2 frequency transition point , 4th motor A595 Acc1 to Acc2 frequency transition point , 5th motor A096 Dec1 to Dec2 frequency transition point A296 Dec1 to Dec2 frequency transition point, 2nd motor A396 Dec1 to Dec2 frequency transition point, 3rd motor A496 Dec1 to Dec2 frequency transition point, 4th motor A596 Dec1 to Dec2 frequency transition point, 5th motor A097 Acceleration curve selection A098 Deceleration curve selection A101 [OI]–[L] input active range start frequency A102 [OI]–[L] input active range end frequency A103 [OI]–[L] input active range start current A104 [OI]–[L] input active range end current A105 [OI]–[L] input start frequency enable A111 [O2]-[L] input active range start frequency A112 [O2]-[L] input active range end frequency A113 [O2]-[L] input active range start voltage A114 [O2]-[L] input active range end voltage A131 Acceleration curve constants setting A132 Deceleration curve constants setting [A-SigDataEnd] [b-SigData] b001 Selection of restart mode b002 Allowable under-voltage power failure time b003 Retry wait time before motor restart b004 Instantaneous power failure / under-voltage trip alarm enable b005 Number of restart on power failure / under-voltage trip events b006 Phase loss detection enable b007 Restart frequency threshold b012 Electronic thermal setting (calculated within the inverter from current output) b013 Electronic thermal characteristic b015 Free setting electronic thermal frequency (1) b016 Free setting electronic thermal current (1) b017 Free setting electronic thermal frequency (2) b018 Free setting electronic thermal current (2) b019 Free setting electronic thermal frequency (3) b020 Free setting electronic thermal current (3) b212 Electronic thermal setting (calculated within the inverter from current output), 2nd motor b213 Electronic thermal characteristic, 2nd motor b215 Free setting electronic thermal frequency (1), 2nd motor b216 Free setting electronic thermal current (1), 2nd motor b217 Free setting electronic thermal frequency (2), 2nd motor b218 Free setting electronic thermal current (2), 2nd motor b219 Free setting electronic thermal frequency (3), 2nd motor b220 Free setting electronic thermal current (3), 2nd motor b312 Electronic thermal setting (calculated within the inverter from current output), 3rd motor b313 Electronic thermal characteristic, 3rd motor b315 Free setting electronic thermal frequency (1), 3rd motor b316 Free setting electronic thermal current (1), 3rd motor b317 Free setting electronic thermal frequency (2), 3rd motor b318 Free setting electronic thermal current (2), 3rd motor b319 Free setting electronic thermal frequency (3), 3rd motor b320 Free setting electronic thermal current (3), 3rd motor b412 Electronic thermal setting (calculated within the inverter from current output), 4th motor b413 Electronic thermal characteristic, 4th motor b415 Free setting electronic thermal frequency (1), 4th motor b416 Free setting electronic thermal current (1), 4th motor b417 Free setting electronic thermal frequency (2), 4th motor b418 Free setting electronic thermal current (2), 4th motor b419 Free setting electronic thermal frequency (3), 4th motor b420 Free setting electronic thermal current (3), 4th motor b512 Electronic thermal setting (calculated within the inverter from current output), 5th motor b513 Electronic thermal characteristic, 5th motor b515 Free setting electronic thermal frequency (1), 5th motor b516 Free setting electronic thermal current (1), 5th motor b517 Free setting electronic thermal frequency (2), 5th motor b518 Free setting electronic thermal current (2), 5th motor b519 Free setting electronic thermal frequency (3), 5th motor b520 Free setting electronic thermal current (3), 5th motor b021 Overload restriction operation mode b221 Overload restriction operation mode, 2nd motor b321 Overload restriction operation mode, 3rd motor b421 Overload restriction operation mode, 4th motor b521 Overload restriction operation mode, 5th motor b022 Overload restriction setting b222 Overload restriction setting, 2nd motor b322 Overload restriction setting, 3rd motor b422 Overload restriction setting, 4th motor b522 Overload restriction setting, 5th motor b023 Deceleration rate at overload restriction b223 Deceleration rate at overload restriction, 2nd motor b323 Deceleration rate at overload restriction, 3rd motor b423 Deceleration rate at overload restriction, 4th motor b523 Deceleration rate at overload restriction, 5th motor b031 Software lock mode selection b034 Run/power-on warning time b035 Rotational direction restriction b036 Reduced voltage start selection b037 Function code display restriction b080 [AM] terminal analog meter adjustment b081 [FM] terminal analog meter adjustment b082 Start frequency adjustment b083 Carrier frequency setting b084 Initialization mode (parameters or trip history) b085 Country code for initialization b086 Frequency scaling conversion factor b087 STOP key enable b088 Restart mode after FRS b090 Dynamic braking usage ratio b091 Stop mode selection b092 Cooling fan control b095 Dynamic braking control b096 Dynamic braking activation level b098 Thermistor for thermal protection control b099 Thermal protection level setting b100 Free-setting V/f frequency (1) b101 Free-setting V/f voltage (1) b102 Free-setting V/f frequency (2) b103 Free-setting V/f voltage (2) b104 Free-setting V/f frequency (3) b105 Free-setting V/f voltage (3) b106 Free-setting V/f frequency (4) b107 Free-setting V/f voltage (4) b108 Free-setting V/f frequency (5) b109 Free-setting V/f voltage (5) b110 Free-setting V/f frequency (6) b111 Free-setting V/f voltage (6) b112 Free-setting V/f frequency (7) b113 Free-setting V/f voltage (7) [b-SigDataEnd] [C-SigData] C001 Terminal [1] function C002 Terminal [2] function C003 Terminal [3] function C004 Terminal [4] function C005 Terminal [5] function C006 Terminal [6] function C007 Terminal [7] function C008 Terminal [8] function C011 Terminal [1] active state C012 Terminal [2] active state C013 Terminal [3] active state C014 Terminal [4] active state C015 Terminal [5] active state C016 Terminal [6] active state C017 Terminal [7] active state C018 Terminal [8] active state C019 Terminal [FW] active state C021 Terminal [11] function C022 Terminal [12] function C023 Terminal [13] function C024 Terminal [14] function C025 Terminal [15] function C026 Alarm relay terminal function C027 [FM] signal selection C028 [AM] signal selection C029 [AMI] signal selection C031 Terminal [11] active state C032 Terminal [12] active state C033 Terminal [13] active state C034 Terminal [14] active state C035 Terminal [15] active state C036 Alarm relay active state C040 Overload signal output mode C041 Overload level setting C241 Overload level setting, 2nd C341 Overload level setting, 3rd C441 Overload level setting, 4th C541 Overload level setting, 5th C042 Frequency arrival setting for accel C043 Arrival frequency setting for decel C061 Electronic thermal warning level setting C062 Alarm code output C070 Data command method C071 Communication speed selection C072 Node allocation C073 Communication data length selection C074 Communication parity selection C075 Communication stop bit selection C078 Communication wait time C081 [O] input span calibration C082 [O1] input span calibration C083 [O2] input span calibration C085 Thermistor input tuning C086 [AM] terminal offset tuning C087 [AMI] terminal meter tuning C088 [AMI] terminal offset tuning C091 Debug mode enable C101 Up/Down memory mode selection C102 Reset mode selection C103 Restart mode after reset C121 [O] input zero calibration C122 [OI] input zero calibration C123 [O2] input zero calibration [C-SigDataEnd] [H-SigData] H003 Motor capacity, 1st motor H203 Motor capacity, 2nd motor H303 Motor capacity, 3rd motor H403 Motor capacity, 4th motor H503 Motor capacity, 5th motor H004 Motor poles setting, 1st motor H204 Motor poles setting, 2nd motor H304 Motor poles setting, 3rd motor H404 Motor poles setting, 4th motor H504 Motor poles setting, 5th motor H006 Motor stabilization constant, 1st motor H206 Motor stabilization constant, 2nd motor H306 Motor stabilization constant, 3rd motor H406 Motor stabilization constant, 4th motor H506 Motor stabilization constant, 5th motor [H-SigDataEnd] [P-SigData] P001 Operation mode on expansion card 1 error P002 Operation mode on expansion card 2 error P031 Accel/decel time input selection [P-SigDataEnd]