Series:L200 DataFormat=Hex [SigData] 00001 Run command 00002 FW/REV command 00003 External trip (EXT) 00004 Trip reset (RS) 00007 Intelligent input terminal 1 00008 Intelligent input terminal 2 00009 Intelligent input terminal 3 0000A Intelligent input terminal 4 0000B Intelligent input terminal 5 0000E Run/Stop status 0000F FW/REV status 00010 Inverter ready 00014 Alarm signal 00015 PID deviation signal 00016 Overload signal 00017 Frequency arrival signal (set frequency or above) 00018 Frequency arrival signal (at constant speed) 00019 Run Mode signal 0001A Data writing 0001B CRC error 0001C Overrun error 0001D Framing error 0001E Parity error 0001F Check sum error 40001 Output frequency command 40002 Inverter status 40003 Process Variable (PV) 4000A Output frequency monitor 4000B Output current monitor 4000C Rotation direction monitor 4000D Process variable (PV), PID feedback monitor (high) 4000E Process variable (PV), PID feedback monitor (low) 4000F Intelligent input terminal status 40010 Intelligent output terminal status 40011 Scaled output frequency monitor (high) 40012 Scaled output frequency monitor (low) 40013 Output voltage monitor 40014 Cumulative operation RUN time monitor (high) 40015 Cumulative operation RUN time monitor (low) 40016 Cumulative power-on time monitor (high) 40017 Cumulative power-on time monitor (low) 40018 Trip counter 40019 Trip monitor 1 4001A Trip monitor 2 4001B Trip monitor 3 40023 Output frequency setting 40024 Acceleration (1) time setting (high) 40025 Acceleration (1) time setting (low) 40026 Acceleration (1) time setting, 2nd motor (high) 40027 Acceleration (1) time setting, 2nd motor (low) 40028 Deceleration (1) time setting (high) 40029 Deceleration (1) time setting (low) 4002A Deceleration (1) time setting, 2nd motor (high) 4002B Deceleration (1) time setting, 2nd motor (low) 4002C Keypad Run key routing 4002D Frequency source setting 4002E Run command source setting 4002F Base frequency setting 40030 Base frequency setting, 2nd motor 40031 Maximum frequency setting 40032 Maximum frequency setting, 2nd motor 40033 [AT] selection 40034 Pot./O–L input active range start frequency 40035 Pot./O–L input active range end frequency 40036 Pot./O–L input active range start voltage 40037 Pot./O–L input active range end voltage 40038 Pot./O–L input start frequency enable 40039 External frequency filter time constant 4003A Multi-speed 0 setting 4003B Multi-speed 0 setting, 2nd motor 4003C Multi-speed 1 setting 4003D Multi-speed 2 setting 4003E Multi-speed 3 setting 4003F Multi-speed 4 setting 40040 Multi-speed 5 setting 40041 Multi-speed 6 setting 40042 Multi-speed 7 setting 40043 Multi-speed 8 setting 40044 Multi-speed 9 setting 40045 Multi-speed 10 setting 40046 Multi-speed 11 setting 40047 Multi-speed 12 setting 40048 Multi-speed 13 setting 40049 Multi-speed 14 setting 4004A Multi-speed 15 setting 4004B Jog frequency setting 4004C Jog stop mode 4004D Torque boost select 4004E Torque boost select, 2nd motor 4004F Manual torque boost value 40050 Manual torque boost value, 2nd motor 40051 Manual torque boost frequency adjustment 40052 Manual torque boost frequency adjustment, 2nd motor 40053 V/f characteristic curve selection 40054 V/f characteristic curve selection, 2nd motor 40055 V/f gain setting 4005C DC braking enable 4005D DC braking frequency setting 4005E DC braking wait time 4005F DC braking force for deceleration 40060 DC braking time for deceleration 40061 DC braking / edge or level detection for [DB] input 40062 Frequency upper limit setting 40063 Frequency upper limit setting, 2nd motor 40064 Frequency lower limit setting 40065 Frequency lower limit setting, 2nd motor 40066 Jump (center) frequency setting 40067 Jump (hysteresis) frequency width setting 40068 Jump (center) frequency setting 40069 Jump (hysteresis) frequency width setting 4006A Jump (center) frequency setting 4006B Jump (hysteresis) frequency width setting 4006C PID Enable 4006D PID proportional gain 4006E PID integral time constant 4006F PID derivative time constant 40070 PV scale conversion 40071 PV source setting 40072 AVR function select 40073 AVR voltage select 40074 Acceleration (2) time setting (high) 40075 Acceleration (2) time setting (low) 40076 Acceleration (2) time setting, (2nd motor) (high) 40077 Acceleration (2) time setting, (2nd motor) (low) 40078 Deceleration (2) time setting (high) 40079 Deceleration (2) time setting (low) 4007A Deceleration (2) time setting, (2nd motor) (high) 4007B Deceleration (2) time setting, (2nd motor) (low) 4007C Select method to switch to Acc2/Dec2 profile 4007D Select method to switch to Acc2/Dec2 profile, 2nd motor 4007E Acc1 to Acc2 frequency transition point 4007F Acc1 to Acc2 frequency transition point, 2nd motor 40080 Dec1 to Dec2 frequency transition point 40081 Dec1 to Dec2 frequency transition point, 2nd motor 40082 Acceleration curve selection 40083 Deceleration curve selection 40084 [OI]–[L] input active range start frequency 40085 [OI]–[L] input active range end frequency 40086 [OI]–[L] input active range start current 40087 [OI]–[L] input active range end current 40088 [OI]–[L] input start frequency enable 40089 Selection of automatic restart mode 4008A Allowable undervoltage power failure time 4008B Retry wait time before motor restart 4008C Instantaneous power failure / under-voltage trip alarm enable 4008D Number of restarts on power failure / under-voltage trip events 4008E Level of electronic thermal setting 4008F Level of electronic thermal setting, 2nd motor 40090 Electronic thermal characteristic 40091 Electronic thermal characteristic, 2nd motor 40092 Overload restriction operation mode 40093 Overload restriction setting 40094 Deceleration rate at overload restriction 40095 Software lock mode selection 40096 [AM] analog signal gain 40098 Start frequency adjustment 40099 Carrier frequency setting 4009A Initialization mode (parameters or trip history) 4009B Country code for initialization (not accessible to ModBus) 4009C Frequency scaling conversion factor 4009D STOP key enable 4009E Restart mode after FRS 400A0 Stop mode selection 400A4 Over-voltage LADSTOP enable 400A6 Carrier mode (not accessible to ModBus) 400A7 Terminal [1] function 400A8 Terminal [2] function 400A9 Terminal [3] function 400AA Terminal [4] function 400AB Terminal [5] function 400AD Terminal [1] active state 400AE Terminal [2] active state 400AF Terminal [3] active state 400B0 Terminal [4] active state 400B1 Terminal [5] active state 400B3 Terminal [11] function 400B4 Terminal [12] function 400B5 Alarm relay terminal function 400B7 [AM] signal selection 400B8 Terminal [11] active state 400B9 Terminal [12] active state 400BA Alarm relay active state 400BB Overload level setting 400BC Frequency arrival setting for acceleration 400BD Arrival frequency setting for deceleration 400BE PID deviation level setting 400C0 Communication speed selection 400C1 Node allocation 400C3 Communication parity selection 400C4 Communication stop bit selection 400C5 Communication wait time 400C7 O input span calibration 400C8 OI input span calibration 400C9 [AM] terminal offset tuning 400CF Up/Down memory mode selection 400D0 Reset selection 400D9 Motor capacity 400DA Motor capacity, 2nd setting 400DB Motor poles setting 400DC Motor poles setting, 2nd motor 400DD Motor stabilization constant 400DE Motor stabilization constant, 2nd motor 400E1 Reverse PID action 400E2 PID output limit 400E3 A input select for calculate function 400E4 B input select for calculate function 400E5 Calculation symbol 400E6 ADD frequency 400E7 ADD direction select 400E8 Reactive current setting 400E9 Monitor display select for networked inverter 400EA PID FBV function high limit 400EB PID FBV function low limit 400EC Communication error select 400ED Communication error time-out 400EE Thermistor input tuning 400EF Input A select for logic output 400F0 Input B select for logic output 400F1 Logic function select 400F2 Terminal [11] ON delay 400F3 Terminal [11] OFF delay 400F4 Terminal [12] ON delay 400F5 Terminal [12] OFF delay 400F6 Output relay ON delay 400F7 Output relay OFF delay 40100 Trip monitor 1: factor code 40101 Trip monitor 1: Frequency 40102 Trip monitor 1: Current 40103 Trip monitor 1: Voltage 40104 Trip monitor 1: Run time (high) 40105 Trip monitor 1: Run time (low) 40106 Trip monitor 1: ON time (high) 40107 Trip monitor 1: ON time (low) 40108 Trip monitor 2: factor code 40109 Trip monitor 2: Frequency 4010A Trip monitor 2: Current 4010B Trip monitor 2: Voltage 4010C Trip monitor 2: Run time (high) 4010D Trip monitor 2: Run time (low) 4010E Trip monitor 2: ON time (high) 4010F Trip monitor 2: ON time (low) 40110 Trip monitor 3: factor code 40111 Trip monitor 3: Frequency 40112 Trip monitor 3: Current 40113 Trip monitor 3: Voltage 40114 Trip monitor 3: Run time (high) 40115 Trip monitor 3: Run time (low) 40116 Trip monitor 3: ON time (high) 40117 Trip monitor 3: ON time (low) 40900 Write all memory [SigDataEnd]