Series:X200 DataFormat=Hex [SigData] 00001 Run command 00002 FW/RV command 00003 External trip (EXT) 00004 Trip reset (RS) 00007 Intelligent input terminal 1 00008 Intelligent input terminal 2 00009 Intelligent input terminal 3 0000A Intelligent input terminal 4 0000B Intelligent input terminal 5 0000E Run/Stop status 0000F FW/RV status 00010 Inverter ready 00014 Alarm signal 00015 PID deviation signal 00016 Overload signal 00017 Frequency arrival signal(set frequency or above) 00018 Frequency arrival signal(at constant speed) 00019 Run Mode signal 0001A Data writing 0001B CRC error 0001C Overrun error 0001D Framing error 0001E Parity error 0001F Check sum error 40002 Output frequency command 40003 Inverter status 40005 Process Variable (PV) 40011 Trip counter 40012 Trip monitor 1: factor code 40014 Trip monitor 1: Frequency 40016 Trip monitor 1: Current 40017 Trip monitor 1: Voltage 40018 Trip monitor 1: Run time (high) 40019 Trip monitor 1: Run time (low) 4001A Trip monitor 1: ON time (high) 4001B Trip monitor 1: ON time (low) 4001C Trip monitor 2: factor code 4001E Trip monitor 2: Frequency 40020 Trip monitor 2: Current 40021 Trip monitor 2: Voltage 40022 Trip monitor 2: Run time (high) 40023 Trip monitor 2: Run time (low) 40024 Trip monitor 2: ON time (high) 40025 Trip monitor 2: ON time (low) 40026 Trip monitor 3: factor code 40028 Trip monitor 3: Frequency 4002A Trip monitor 3: Current 4002B Trip monitor 3: Voltage 4002C Trip monitor 3: Run time (high) 4002D Trip monitor 3: Run time (low) 4002E Trip monitor 3: ON time (high) 4002F Trip monitor 3: ON time (low) 40900 ENTER Command 41002 Output frequency monitor 41003 Output current monitor 41004 Rotation direction monitor 41005 Process Variable (PV), PID feedback monitor (high) 41006 Process Variable (PV), PID feedback monitor (low) 41007 Intelligent input terminal status 41008 Intelligent output terminal status 41009 Scaled output frequency monitor (high) 4100A Scaled output frequency monitor (low) 4100C Output voltage monitor 4100E Cumulative operation RUN time monitor (high) 4100F Cumulative operation RUN time monitor (low) 41010 Cumulative power-on time monitor (high) 41011 Cumulative power-on time monitor (low) 41014 Acceleration (1) time setting (high) 41015 Acceleration (1) time setting (low) 41016 Deceleration (1) time setting (high) 41017 Deceleration (1) time setting (low) 41018 Keypad Run key routing 41019 Frequency source setting 4101A Run command source setting 4101B Base frequency setting 4101C Maximum frequency setting 4101D [AT] selection 41020 O–L input active range start frequency 41022 O–L input active range end frequency 41023 O–L input active range start voltage 41024 O–L input active range end voltage 41025 O–L input start frequency enable 41026 External frequency filter time constant 41029 Multi-speed 0 setting 4102B Multi-speed 1 setting 4102D Multi-speed 2 setting 4102F Multi-speed 3 setting 41031 Multi-speed 4 setting 41033 Multi-speed 5 setting 41035 Multi-speed 6 setting 41037 Multi-speed 7 setting 41039 Multi-speed 8 setting 4103B Multi-speed 9 setting 4103D Multi-speed 10 setting 4103F Multi-speed 11 setting 41041 Multi-speed 12 setting 41043 Multi-speed 13 setting 41045 Multi-speed 14 setting 41047 Multi-speed 15 setting 41048 Jog frequency setting 41049 Jog stop mode 4104A Torque boost select 4104B Manual torque boost value 4104C Manual torque boost frequency adjustment 4104D V/f characteristic curve selection 4104E V/f gain setting 41051 DC braking enable 41052 DC braking frequency setting 41053 DC braking wait time 41054 DC braking force for deceleration 41055 DC braking time for deceleration 41056 DC braking / edge or level detection for [DB] input 4105A Frequency upper limit setting 4105B Frequency lower limit setting 4105D Jump (center) frequency setting 4105E Jump (hysteresis) frequency width setting 41060 Jump (center) frequency setting 41061 Jump (hysteresis) frequency width setting 41063 Jump (center) frequency setting 41064 Jump (hysteresis) frequency width setting 41068 PID enable 41069 PID proportional gain 4106A PID integral time constant 4106B PID derivative time constant 4106C PV scale conversion 4106D PV source setting 4106E Reverse PID action 4106F PID output limit 41070 AVR function select 41071 AVR voltage select 41072 Operation mode selection 41073 Energy saving mode tuning 41074 Acceleration (2) time setting (high) 41075 Acceleration (2) time setting (low) 41076 Deceleration (2) time setting (high) 41077 Deceleration (2) time setting (low) 41078 Select method to switch to Acc2/Dec2 profile 4107A Acc1 to Acc2 frequency transition point 4107C Dec1 to Dec2 frequency transition point 4107D Acceleration curve selection 4107E Deceleration curve selection 41080 [OI]-[L] input active range start frequency 41082 [OI]-[L] input active range end frequency 41083 [OI]-[L] input active range start current 41084 [OI]-[L] input active range end voltage 41085 [OI]-[L] input start frequency enable 4108E A input select for calculate function 4108F B input select for calculate function 41090 Calculation symbol 41091 ADD frequency 41093 ADD direction select 41095 POT active range start frequency 41097 POT input active range end frequency 41098 POT input active range start 41099 POT input active range end 4109A POT input start frequency enable 410A5 Selection of automatic restart mode 410A6 Allowable under-voltage power failure time 410A7 Retry wait time before motor restart 410A8 Instantaneous power failure / under-voltage trip alarm enable 410A9 Number of restarts on power failure / under-voltage trip events 410AD Level of electronic thermal setting 410AE Electronic thermal characteristic 410B5 Overload restriction operation mode 410B6 Overload restriction level setting 410B7 Deceleration rate at overload restriction 410BB Source of overload restriction selection 410BC Software lock mode selection 410C9 Selection of the non stop operation 410CA Non stop operation start voltage setting 410CB OV-LAD Stop level of non stop operation setting 410CC Deceleration time of non stop operation setting 410CE Frequency width of quick deceleration setting 410CF [AM]analog signal gain 410D1 Start frequency adjustment 410D2 Carrier frequency setting 410D3 Initialization mode (parameters or trip history) 410D4 Country for initialization 410D5 Frequency scaling conversion factor 410D6 STOP key enable 410D7 Restart mode after FRS 410D8 Monitor display select for networked inverter 410DA Stop mode selection 410DB Cooling fan control 410F5 Over-voltage LADSTOP enable 410F6 Over-voltage LADSTOP level 410F7 Over-current trip suppression 410F8 Carrier mode 410F9 Selection of RDY function 41103 Terminal [1] function 41104 Terminal [2] function 41105 Terminal [3] function 41106 Terminal [4] function 41107 Terminal [5] function 4110B Terminal [1] active state 4110C Terminal [2] active state 4110D Terminal [3] active state 4110E Terminal [4] active state 4110F Terminal [5] active state 41114 Terminal [11] function 41119 Alarm relay terminal function 4111B [AM] signal selection 4111D Terminal [11] active state 41122 Alarm relay active state 41124 Overload level setting 41126 Frequency arrival setting for acceleration 41128 Frequency arrival setting for deceleration 41129 PID deviation level setting 4112E PID FBV function high limit 4112F PID FBV function variable low limit 41137 Selection of OPE / ModBus 41138 Communication speed selection 41139 Node allocation 4113B Communication parity selection 4113C Communication stop bit selection 4113D Communication error select 4113E Communication error time-out 4113F Communication wait time 41141 O input span calibration 41142 OI input span calibration 41145 AM offset calibration 41149 Up/Down memory mode selection 4114A Reset selection 41150 Input A select for logic output 41151 Input B select for logic output 41152 Logic function select 41153 Terminal [11] ON delay 41154 Terminal [11] OFF delay 41157 Output relay ON delay 41158 Output relay OFF delay 41165 Motor capacity 41166 Motor poles setting 41168 Motor stabilization constant 4116A Fin temperature monitor 4116C DC voltage monitor 4116D Electronic thermal monitor 41170 Start freq to be used in case of freq pull-in restart 41171 Deceleration rate of frequency pull-in restart setting 41172 Current level of frequency pull-in restart setting 41173 DC bus AVR P-gain 41174 DC bus AVR I-time 41176 DC bus AVR selection 41177 Threshold voltage of DC bus AVR setting 41178 Output mode of low load detection signal 41179 Low load detection level 41501 Acceleration (1) time setting, 2nd motor (high) 41502 Acceleration (1) time setting, 2nd motor (low) 41503 Deceleration (1) time setting, 2nd motor (high) 41504 Deceleration (1) time setting, 2nd motor (low) 4150C Base frequency setting, 2nd motor 4150D Maximum frequency setting, 2nd motor 4150F Multi-speed 0 setting 2nd motor 41510 Torque boost select, 2nd motor 41511 Manual torque boost value, 2nd motor 41512 Manual torque boost frequency adjustment, 2nd motor 41513 V/f characteristic curve selection, 2nd motor 41514 V/f gain setting, 2nd motor 41517 Frequency upper limit setting, 2nd motor 41518 Frequency lower limit setting, 2nd motor 41519 Acceleration (2) time setting, 2nd motor (high) 4151A Acceleration (2) time setting, 2nd motor (low) 4151B Deceleration (2) time setting, 2nd motor (high) 4151C Deceleration (2) time setting, 2nd motor (low) 4151D Select method to switch to Acc2/Dec2 profile, 2nd motor 4151F Acc1 to Acc2 frequency transition point, 2nd motor 41521 Dec1 to Dec2 frequency transition point, 2nd motor 41527 Level of electronic thermal setting, 2nd motor 41528 Electronic thermal characteristic, 2nd motor 41529 Overload restriction operation mode, 2nd motor 4152A Overload restriction level setting, 2nd motor 4152B Deceleration rate at overload restriction, 2nd motor 4152C Source of overload restriction selection, 2nd motor 41532 Terminal [1] function, 2nd motor 41533 Terminal [2] function, 2nd motor 41534 Terminal [3] function, 2nd motor 41535 Terminal [4] function, 2nd motor 41536 Terminal [5] function, 2nd motor 4153A Overload level setting, 2nd motor 41541 Motor capacity, 2nd motor 41542 Motor poles setting, 2nd motor 41544 Motor stabilization constant, 2nd motor [SigDataEnd]