Series: FR-A700 DataFormat=Dec [P-SigData] 000 Torque boost 001 Maximum frequency 002 Minimum frequency 003 Base frequency 004 Multi-speed setting (high speed) 005 Multi-speed setting (middle speed) 006 Multi-speed setting (low speed) 007 Acceleration time 008 Deceleration time 009 Electronic thermal O/L relay 010 DC injection brake operation frequency 011 DC injection brake operation time 012 DC injection brake operation voltage 013 Starting frequency 014 Load pattern selection 015 Jog frequency 016 Jog acceleration/deceleration time 017 MRS input selection 018 High speed maximum frequency 019 Base frequency voltage 020 Acceleration/deceleration reference frequency 021 Acceleration/deceleration time increments 022 Stall prevention operation level (Torque limit level ) 023 Stall prevention operation level compensation factor at double speed 024 Multi-speed setting (speed 4) 025 Multi-speed setting (speed 5) 026 Multi-speed setting (speed 6) 027 Multi-speed setting (speed 7) 028 Multi-speed input compensation selection 029 Acceleration/deceleration pattern selection 030 Regenerative function selection (FR-A700 only) 031 Frequency jump 1A 032 Frequency jump 1B 033 Frequency jump 2A 034 Frequency jump 2B 035 Frequency jump 3A 036 Frequency jump 3B 037 Speed display 041 Up-to-frequency sensitivity 042 Output frequency detection 043 Output frequency detection for reverse rotation 044 Second acceleration/deceleration time 045 Second deceleration time 046 Second torque boost 047 Second V/F (base frequency) 048 Second stall prevention operation current 049 Second stall prevention operation frequency 050 Second output frequency detection 051 Second electronic thermal O/L relay 052 DU/PU main display data selection 054 FM terminal function selection 055 Frequency monitoring reference 056 Current monitoring reference 057 Restart coasting time 058 Restart cushion time 059 Remote function selection 060 Energy saving control selection 061 Reference current 062 Reference value at acceleration 063 Reference value at dcceleration 064 Starting frequency for elevator mode 065 Retry selection 066 Stall prevention operation reduction starting frequency 067 Number of retries at alarm occurrence 068 Retry waiting time 069 Retry count display erase 070 Special regenerative brake duty (FR-A700 only) 071 Applied motor 072 PWM frequency selection 073 Analog input selection 074 Input filter time constant 075 Reset selection/disconnected PU detection/PU stop selection 076 Alarm code output selection 077 Parameter write selection 078 Reverse rotation prevention selection 079 Operation mode selection 080 Motor capacity 081 Number of motor poles 082 Motor excitation current 083 Motor rated voltage 084 Rated motor frequency 089 Speed control gain (magnetic flux vector) 090 Motor constant (R1) 091 Motor constant (R2) 092 Motor constant (L1) 093 Motor constant (L2) 094 Motor constant (X) 095 Online auto tuning selection 096 Auto tuning setting/status 100 V/F1 (first frequency) 101 V/F1 (first frequency voltage) 102 V/F2 (second frequency) 103 V/F2 (second frequency voltage) 104 V/F3 (third frequency) 105 V/F3 (third frequency voltage) 106 V/F4 (fourth frequency) 107 V/F4 (fourth frequency voltage) 108 V/F5 (fifth frequency) 109 V/F5 (fifth frequency voltage) 110 Third acceleration/deceleration time 111 Third deceleration time 112 Third torque boost 113 Third V/F (base frequency) 114 Third stall prevention operation current 115 Thrid stall prevention operation frequency 116 Third output frequency detection 117 PU communication station number 118 PU communication speed 119 PU communication stop bit length 120 PU communication parity check 121 Number of PU communication retries 122 PU communication check time interval 123 PU communication waiting time setting 124 PU communication CR/LF presence/absence selection 125 Terminal 2 frequency setting gain frequency 126 Terminal 4 frequency setting gain frequency 127 PID control automatic switchover freqeuncy 128 PID action selection 129 PID proportional band 130 PID integral time 131 PID upper limit 132 PID lower limit 133 PID action set point 134 PID differential time 135 Electronic bypass sequence selection 136 MC switchover interlock time 137 Start waiting time 138 Bypass selection at an alarm 139 Automatic switchover frequency from inverter to bypass operation 140 Backlash acceleration stopping frequency 141 Backlash acceleration stopping time 142 Backlash deceleration stopping frequency 143 Backlash deceleration stopping time 144 Speed setting switchover 145 PU display language selection 148 Stall prevention level at 0V input 149 Stall prevention level at 10V input 150 Output current detection level 151 Output current detection signal delay time 152 Zero current detection level 153 Zero current detection time 154 Voltage reduction selection during stall prevention operation 155 RT signal function validity condition selection 156 Stall prevention operation selection 157 OL signal output timer 158 AM terminal function selection 159 Automatic switchover frequency range from bypass to inverter operation 160 User group read selection 161 Frequency setting/key lock operation selection 162 Automatic restart after instantaneous power failure selection 163 First cushion time for restart 164 First cushion voltage for restart 165 Stall prevention operation level for restart 166 Output current detection signal retention time 167 Output current detection operation selection 170 Watt-hour meter clear 171 Operation hour meter clear 172 User group registered display/batch clear 173 User group registration 174 User group clear 178 STF terminal function selection 179 STR terminal function selection 180 RL terminal function selection 181 RM terminal function selection 182 RH terminal function selection 183 RT terminal function selection 184 AU terminal function selection 185 JOG terminal function selection 186 CS terminal function selection 187 MRS terminal function selection 188 STOP terminal function selection 189 RES terminal function selection 190 RUN terminal function selection 191 SU terminal function selection 192 IPF terminal function selection 193 OL terminal function selection 194 FU terminal function selection 195 ABC1 terminal function selection 196 ABC2 terminal function selection 232 Multi-speed setting (speed 8) 233 Multi-speed setting (speed 9) 234 Multi-speed setting (speed 10) 235 Multi-speed setting (speed 11) 236 Multi-speed setting (speed 12) 237 Multi-speed setting (speed 13) 238 Multi-speed setting (speed 14) 239 Multi-speed setting (speed 15) 240 Soft-PWM operation selection 241 Analog input display unit switchover 242 Terminal 1 added compensation amount (terminal 2) 243 Terminal 1 added compensation amount (terminal 4) 244 Cooling fan operation selection 245 Rated slip 246 Slip compensation time constant 247 Constant-power region slip compensation selection 250 Stop selection 251 Output phase failure protection selection 252 Override bias 253 Override gain 255 Life alarm status display 256 Inrush current limit circuit life display 257 Control circuit capacitor life display 258 Main circuit capacitor life display 259 Main circuit capacitor life measuring 261 Power failure stop selection 262 Subtracted frequency at deceleration start 263 Subtraction starting frequency 264 Power-failure deceleration time 1 265 Power-failure deceleration time 2 266 Power failure deceleration time switchover frequency 267 Terminal 4 input selection 268 Monitor decimal digits selection 270 Stop-on contact/load torque high-speed frequency control selection 271 High-speed setting maximum current 272 Middle-speed setting minimum current 273 Current averaging range 274 Current averaging filter time constant 275 Stop-on contact excitation current low-speed multiplying factor 276 PWM carrier frequency at stop-on contact 278 Brake opening frequency 279 Brake opening current 280 Brake opening current detection time 281 Brake operation time at start 282 Brake operation frequency 283 Brake operation time at stop 284 Deceleration detection function selection 285 Overspeed detection frequency (Excessive speed deviation detection frequency) 286 Droop gain 287 Droop filter time constant 288 Droop function activation selection 291 Pulse train I/O selection 292 Automatic acceleration/deceleration 293 Acceleration/deceleration time individual calculation selection 294 UV avoidance voltage gain 299 Rotation direction detection selection at restarting 300 BCD input bias 301 BCD input gain 302 BIN input bias 303 BIN input gain 304 Digital input and analog input compensation enable/disable selection 305 Read timing operation selection 306 Analog output signal selection 307 Setting for zero analog output 308 Setting for maximum analog output 309 Analog output signal voltage/current switchover 310 Analog meter voltage output selection 311 Setting for zero analog meter voltage output 312 Setting for maximum analog meter voltage output 313 DO0 output selection 314 DO1 output selection 315 DO2 output selection 316 DO3 output selection 317 DO4 output selection 318 DO5 output selection 319 DO6 output selection 320 RA1 output selection 321 RA2 output selection 322 RA3 output selection 323 AM0 0V adjustment 324 AM1 0mA adjustment 329 Digital input unit selection 331 RS-485 communication station 332 RS-485 communication speed 333 RS-485 communication stop bit length 334 RS-485 communication parity check selection 335 RS-485 communication retry count 336 RS-485 communication check time interval 337 RS-485 communication waiting time setting 338 Communication operation command source 339 Communication speed command source 340 Communication startup mode selection 341 RS-485 communication CR/LF selection 342 Communication EEPROM write selection 343 Communication error count 345 DeviceNet address start data 346 DeviceNet baud rate 349 Communication reset selection 350 Stop position command selection 351 Orientation speed 352 Creep speed 353 Creep switchover position 354 Position loop switchover position 355 DC injection brake start position 356 Internal stop position command 357 Orientation in-position zone 358 Servo torque selection 359 Encoder rotation direction 360 16 bit data selection 361 Position shift 362 Orientation position loop gain 363 Completion signal output delay time 364 Encoder stop check time 365 Orientation limit 366 Recheck time 367 Speed feedback range 368 Feedback gain 369 Number of encoder pulses 374 Overspeed detection level 376 Encoder signal loss detection enable/disable selection 379 SSCNETⅢ rotation direction selection (FR-A701 only) 380 Acceleration S-pattern 1 381 Deceleration S-pattern 1 382 Acceleration S-pattern 2 383 Deceleration S-pattern 2 384 Input pulse division scaling factor 385 Frequency for 0 input pulse 386 Frequency for maximum input pulse 387 Initial communication delay time 388 Send time interval at hart beat 389 Minimum sending time at hart beat 390 % setting reference frequency 391 Receive time interval at hart beat 392 Event driven detection width 393 Orientation selection 396 Orientation speed gain (P term) 397 Orientation speed integral time 398 Orientation speed gain (D term) 399 Orientation deceleration ratio 406 High resolution analog input selection (FR-A701 only) 407 Motor temperature detection filter (FR-A701 only) 408 Motor thermistor selection (FR-A701 only) 419 Position command source selection 420 Command pulse scaling factor numerator 421 Command pulse scaling factor denominator 422 Position loop gain 423 Position feed forward gain 424 Position command acceleration/deceleration time constant 425 Position feed forward command filter 426 In-position width 427 Excessive level error 428 Command pulse selection 429 Clear signal selection 430 Pulse monitor selection 447 Digital torque command bias 448 Digital torque command gain 449 SSCNETⅢ input filter setting (FR-A701 only) 450 Second applied motor 451 Second motor control method selection 453 Second motor capacity 454 Number of second motor poles 455 Second motor excitation current 456 Rated second motor voltage 457 Rated second motor frequency 458 Second motor constant (R1) 459 Second motor constant (R2) 460 Second motor constant (L1) 461 Second motor constant (L2) 462 Second motor constant (X) 463 Second motor auto tuning setting/status 464 Digital position control sudden stop deceleration time 465 First position feed amount lower 4 digits 466 First position feed amount upper 4 digits 467 Second position feed amount lower 4 digits 468 Second position feed amount upper 4 digits 469 Third position feed amount lower 4 digits 470 Third position feed amount upper 4 digits 471 Fourth position feed amount lower 4 digits 472 Fourth position feed amount upper 4 digits 473 Fifth position feed amount lower 4 digits 474 Fifth position feed amount upper 4 digits 475 Sixth position feed amount lower 4 digits 476 Sixth position feed amount upper 4 digits 477 Seventh position feed amount lower 4 digits 478 Seventh position feed amount upper 4 digits 479 Eighth position feed amount lower 4 digits 480 Eighth position feed amount upper 4 digits 481 Ninth position feed amount lower 4 digits 482 Ninth position feed amount upper 4 digits 483 Tenth position feed amount lower 4 digits 484 Tenth position feed amount upper 4 digits 485 Eleventh position feed amount lower 4 digits 486 Eleventh position feed amount upper 4 digits 487 Twelfth position feed amount lower 4 digits 488 Twelfth position feed amount upper 4 digits 489 Thirteenth position feed amount lower 4 digits 490 Thirteenth position feed amount upper 4 digits 491 Fourteenth position feed amount lower 4 digits 492 Fourteenth position feed amount upper 4 digits 493 Fifteenth position feed amount lower 4 digits 494 Fifteenth position feed amount upper 4 digits 495 Remote output selection 496 Remote output data 1 497 Remote output data 2 499 SSCNETⅢ operation selection (FR-A701 only) 500 Communication error execution waiting time 501 Communication error occurrence count display 502 Stop mode selection at communication error 503 Maintenance timer 504 Maintenance timer alarm output set time 505 Speed setting reference 516 S-pattern time at a start of acceleration 517 S-pattern time at a completion of acceleration 518 S-pattern time at a start of deceleraiton 519 S-pattern time at a completion of deceleraiton 539 Modbus-RTU communication check time interval (FR-A701 only) 541 Frequency command sign selection (CC-Link) 542 Communication station number (CC-Link) 543 Baud rate (CC-Link) 544 CC-Link extended setting 547 USB communication station number (FR-A700 only) 548 USB communication check time interval (FR-A700 only) 549 Protocol selection 550 NET mode operation command source selection 551 PU mode operation command source selection 555 Current average time 556 Data output mask time 557 Current average value monitor signal output reference current 563 Energization time carrying-over times 564 Operating time carrying-over times 569 Second motor speed control gain 571 Holding time at a start 574 Second motor online auto tuning 575 Output interruption detection time 576 Output interruption detection level 577 Output interruption cancel level 611 Acceleration time at a restart 665 Regeneration avoidance frequency gain 684 Tuning data increments switchover 800 Control method selection 802 Pre-excitation selection 803 Constant power range torque characteristic selection 804 Torque command source selection 805 Torque command value (RAM) 806 Torque command value (RAM,EEPROM) 807 Speed limit selection 808 Forward rotation speed limit 809 Reverse rotation speed limit 810 Torque limit input method selection 811 Set resolution switchover 812 Torque limit level (regeneration) 813 Torque limit level (3rd quadrant) 814 Torque limit level (4th quadrant) 815 Torque limit level 2 816 Torque limit level during acceleration 817 Torque limit level during deceleration 818 Easy gain tuning response level setting 819 Easy gain tuning selection 820 Speed control P gain 1 821 Speed control integral time 1 822 Speed setting filter 1 823 Speed detection filter 1 824 Torque control P gain 1 825 Torque control integral time 1 826 Torque setting filter 1 827 Torque detection filter 1 828 Model speed control gain 830 Speed control P gain 2 831 Speed control integral time 2 832 Speed setting filter 2 833 Speed detection filter 2 834 Torque control P gain 2 835 Torque control integral time 2 836 Torque setting filter 2 837 Torque detection filter 2 838 DA1 terminal function selection (FR-A701 only) 839 DA1 output filter (FR-A701 only) 840 Torque bias selection 841 Torque bias 1 842 Torque bias 2 843 Torque bias 3 844 Torque bias filter 845 Torque bias operation time 846 Torque bias balance compensation 847 Fall-time torque bias terminal 1 bias 848 Fall-time torque bias terminal 1 gain 849 Analog input off set adjustment 850 Control operation selection 853 Speed deviation time 854 Excitation ratio 857 DA1-0V adjustment (FR-A701 only) 858 Terminal 4 function assignment 859 Torque current 860 Second motor torque current 862 Notch filter time constant 863 Notch filter depth 864 Torque detection 865 Low speed detection 866 Torque monitoring reference 867 AM output filter 868 Terminal 1 function assignment 872 Input phase failure protection selection 873 Speed limit 874 OLT level setting 875 Fault definition 877 Speed feed forward control/model adaptive speed control selection 878 Speed feed forward filter 879 Speed feed forward torque limit 880 Load inertia ratio 881 Speed feed forward gain 882 Regeneration avoidance operation selection 883 Regeneration avoidance operation level 884 Regeneration avoidance at deceleration detection sensitivity 885 Regeneration avoidance compensation frequency limit value 886 Regeneration avoidance voltage gain 888 Free parameter 1 889 Free parameter 2 891 Cumulative power monitor digit shifted times 892 Load factor 893 Energy saving monitor reference (motor capacity) 894 Control selection during commercial power-supply operation 895 Power saving rate reference value 896 Power unit cost 897 Power saving monitor average time 898 Power saving cumulative monitor clear 899 Operation time rate (estimated value) 900 (C0)FM terminal calibration 901 (C1)AM terminal calibration 902 (C2)Terminal 2 frequency setting bias frequency/(C3)Terminal 2 frequency setting bias 903 (125)Terminal 2 frequency setting gain frequency/(C4)Terminal 2 frequency setting gain 904 (C5)Terminal 4 frequency setting bias frequency/(C6)Terminal 4 frequency setting bias 905 (126)Terminal 4 frequency setting gain frequency/(C7)Terminal 4 frequency setting gain 917 (C12)Terminal 1 bias frequency (speed)/(C13)Terminal 1 bias (speed) 918 (C14)Terminal 1 gain frequency (speed)/(C15)Terminal 1 gain (speed) 919 (C16)Terminal 1 bias command (torque/magnetic flux)/(C17)Terminal 1 bias (torque/magnetic flux) 920 (C18)Terminal 1 gain command (torque/magnetic flux)/(C19)Terminal 1 gain (torque/magnetic flux) 925 (C29)Motor temperature detection calibration (analog input) (FR-A701 only) 926 (C30)Terminal 6 bias frequency (speed)/(C31)Terminal 6 bias (speed) (FR-A701 only) 927 (C32)Terminal 6 gain frequency (speed)/(C33)Terminal 6 gain (speed) (FR-A701 only) 928 (C34)Terminal 6 bias command (torque)/(C35)Terminal 6 bias (torque) (FR-A701 only) 929 (C36)Terminal 6 gain command (torque)/(C37)Terminal 6 gain (torque) (FR-A701 only) 932 (C38)Terminal 4 bias command (torque/magnetic flux)/(C39)Terminal 4 bias (torque/magnetic flux) 933 (C40)Terminal 4 gain command (torque/magnetic flux)/(C41)Terminal 4 gain (torque/magnetic flux) 989 Parameter copy alarm release 990 PU buzzer control 991 PU contrast adjustment [P-SigDataEnd] [S-SigData] S00 Operation mode S01 Output frequency/speed S02 Output current S03 Output voltage S04 Special monitor S05 Special monitor selection No. S06 Output frequency S07 Output current S08 Output voltage S09 Frequency setting S10 Running speed S11 Motor torque S12 Converter output voltage S13 Regenerative brake duty S14 Electronic thermal relay function load factor S15 Output current peak value S16 Converter output voltage peak value S17 Input power S18 Output power S19 Input terminal status S19.00 STF S19.01 STR S19.02 AU S19.03 RT S19.04 RL S19.05 RM S19.06 RH S19.07 JOG S19.08 MRS S19.09 STOP S19.10 RES S19.11 CS S20 Output terminal status S20.00 RUN S20.01 SU S20.02 IPF S20.03 OL S20.04 FU S20.05 ABC1 S20.06 ABC2 S21 Load meter S22 Motor excitation current S23 Position pulse S24 Cumulative energization time S25 Orientation status S26 Actual operation time S27 Motor load factor S28 Cumulative power S29 Torque command S30 Torque current command S31 Motor output S32 Feedback pulse S33 Power saving effect S34 Cumulative saving power S35 PID set point S36 PID measured value S37 PID deviation value S38 Option input terminal status1 S38.00 X0 S38.01 X1 S38.02 X2 S38.03 X3 S38.04 X4 S38.05 X5 S38.06 X6 S38.07 X7 S38.08 X8 S38.09 X9 S38.10 X10 S38.11 X11 S38.12 X12 S38.13 X13 S38.14 X14 S38.15 X15 S39 Option input terminal status2 S39.00 DY S40 Option output terminal status S40.00 Y0 S40.01 Y1 S40.02 Y2 S40.03 Y3 S40.04 Y4 S40.05 Y5 S40.06 Y6 S40.07 RA1 S40.08 RA2 S40.09 RA3 S43 Alarm definition (Latest Nos. 1&2) S44 Alarm definition (Latest Nos. 3&4) S45 Alarm definition (Latest Nos. 5&6) S46 Alarm definition (Latest Nos. 7&8) S47 Run command (extended) S47.00 AU (current input selection) S47.01 Forward rotation command S47.02 Reverse rotation command S47.03 RL (low speed operation command) S47.04 RM (middle speed operation command) S47.05 RH (high speed operation command) S47.06 RT (second function selection) S47.07 MRS (output stop) S47.08 JOG (Jog operation) S47.09 CS (selection of automatic restart after instantaneous power failure) S47.10 STOP (start self-holding) S47.11 RES (reset) S48 Run command S48.00 AU (current input selection) S48.01 Forward rotation command S48.02 Reverse rotation command S48.03 RL (low speed operation command) S48.04 RM (middle speed operation command) S48.05 RH (high speed operation command) S48.06 RT (second function selection) S48.07 MRS (output stop) S49 Inverter status monitor (extended) S49.00 RUN (inverter running) S49.01 Forward rotation S49.02 Reverse rotation S49.03 SU (up to frequency) S49.04 OL (overload) S49.05 IPF (instantaneous power failure) S49.06 FU (frequency detection) S49.07 ABC1 (alarm) S49.08 ABC2 S49.15 Alarm occurrence S50 Inverter status monitor S50.00 RUN (inverter running) S50.01 Forward rotation S50.02 Reverse rotation S50.03 SU (up to frequency) S50.04 OL (overload) S50.05 IPF (instantaneous power failure) S50.06 FU (frequency detection) S50.07 ABC1 (alarm) S51 Set frequency read (RAM) S52 Set frequency read (EEPROM) S53 Set frequency write (RAM) S54 Set frequency write (RAM, EEPROM) S55 Inverter reset S56 Alarm definition all clear S57 All parameter clear S58 Link parameter extended setting S59 Second parameter changing [S-SigDataEnd]