Series: FR-E500 DataFormat=Dec [P-SigData] 000 Torque boost 001 Maximum frequency 002 Minimum frequency 003 Base frequency 004 Multi-speed setting (high speed) 005 Multi-speed setting (middle speed) 006 Multi-speed setting (low speed) 007 Acceleration time 008 Deceleration time 009 Electronic thermal O/L relay 010 DC injection brake operation frequency 011 DC injection brake operation time 012 DC injection brake voltage 013 Starting frequency 014 Load pattern selection 015 Jog frequency 016 Jog acceleration/deceleration time 018 High-speed maximum frequency 019 Base frequency voltage 020 Acceleration/deceleration reference frequency 021 Acceleration/deceleration time increments 022 Stall prevention operation level 023 Stall prevention operation level compensation factor at double speed 024 Multi-speed setting (speed 4) 025 Multi-speed setting (speed 5) 026 Multi-speed setting (speed 6) 027 Multi-speed setting (speed 7) 029 Acceleration/deceleration pattern 030 Regenerative function selection 031 Frequency jump 1A 032 Frequency jump 1B 033 Frequency jump 2A 034 Frequency jump 2B 035 Frequency jump 3A 036 Frequency jump 3B 037 Speed display 038 Frequency at 5V (10V) input 039 Frequency at 20mA input 041 Up-to-frequency sensitivity 042 Output frequency detection 043 Output frequency detection for reverse rotation 044 Second acceleration/deceleration time 045 Second deceleration time 046 Second torque boost 047 Second V/F (base frequency) 048 Second electronic thermal O/L relay 052 Operation panel/PU main display data selection 054 FM terminal function selection 055 Frequency monitoring reference 056 Current monitoring reference 057 Restart coasting time 058 Restart cushion time 059 Remote setting function selection 060 Shortest acceleration/deceleration mode 061 Reference current 062 Reference current for acceleration 063 Reference current for deceleration 065 Retry selection 066 Stall prevention operation level reduction starting frequency 067 Number of retries at alarm occurrence 068 Retry waiting time 069 Retry count display erasure 070 Special regenerative brake duty 071 Applied motor 072 PWM frequency selection 073 0-5V/0-10V selection 074 Filter time constant 075 Reset selection/disconnected PU detection/PU stop selection 077 Parameter write disable selection 078 Reverse rotation prevention selection 079 Operation mode selection 080 Motor capacity 082 Motor excitation current 083 Rated motor voltage 084 Rated motor frequency 090 Motor constant (R1) 096 Auto-tuning setting/status 117 Communication station number 118 Communication speed 119 Stop bit length 120 Parity check presence/absence 121 Number of communication retries 122 Communication check time interval 123 Waiting time setting 124 CR/LF presence/absence selection 128 PID action selection 129 PID proportional band 130 PID integral time 131 Upper limit 132 Lower limit 133 PID action set point for PU operation 134 PID differential time 145 PU display language selection 146 Frequency setting command selection 150 Output current detection level 151 Output current detection period 152 Zero current detection level 153 Zero current detection period 156 Stall prevention operation selection 160 User group read selection 171 Actual operation hour meter clear 173 User group 1 registration 174 User group 1 deletion 175 User group 2 registration 176 User group 2 deletion 180 RL terminal function selection 181 RM terminal function selection 182 RH terminal function selection 183 MRS terminal function selection 190 RUN terminal function selection 191 FU terminal function selection 192 A, B, C terminal function selection 232 Multi-speed setting (speed 8) 233 Multi-speed setting (speed 9) 234 Multi-speed setting (speed 10) 235 Multi-speed setting (speed 11) 236 Multi-speed setting (speed 12) 237 Multi-speed setting (speed 13) 238 Multi-speed setting (speed 14) 239 Multi-speed setting (speed 15) 240 Soft-PWM setting 244 Cooling fan operation selection 245 Rated motor slip 246 Slip compensation response time 247 Constant-output region slip compensation selection 249 Earth (ground) fault detection at start 250 Stop selection 251 Output phase failure protection selection 338 Operation command source 339 Speed command source 340 Link startup mode selection 342 EEPROM write selection 345 DeviceNet address startup data (lower byte) 346 DeviceNet baudrate startup data (lower byte) 347 DeviceNet address startup data (higher byte) 348 DeviceNet baudrate startup data (higher byte) 387 Initial communication delay time 388 Send time interval at hart beat 389 Minimum sending time at hart beat 390 % setting reference frequency 391 Receive time interval at hart beat 392 Event driven detection width 500 Communication error recognition waiting time 501 Communication error occurrence count display 502 Stop mode selection at communication error 555 Current average time 556 Data output mask time 557 Current average value monitor signal output reference current 900 FM terminal calibration 902 Frequency setting voltage bias 903 Frequency setting voltage gain 904 Frequency setting current bias 905 Frequency setting current gain 922 Built-in frequency setting potentiometer bias 923 Built-in frequency setting potentiometer gain 990 PU buzzer control 991 PU contrast adjustment [P-SigDataEnd] [S-SigData] S00 Operation mode S01 Output frequency[speed] S02 Output current S03 Output voltage S43 Alarm definition (Latest Nos. 1&2) S44 Alarm definition (Latest Nos. 3&4) S45 Alarm definition (Latest Nos. 5&6) S46 Alarm definition (Latest Nos. 7&8) S48 Run command S48.01 Forward rotation (STF) S48.02 Reverse rotation (STR) S50 Inverter status monitor S50.00 Inverter running (RUN) S50.01 Forward rotation S50.02 Reverse rotation S50.03 Up to frequency (SU) S50.04 Overload (OL) S50.06 Frequency detection (FU) S50.07 Alarm occurrence S51 Set frequency read (RAM) S52 Set frequency read (EEPROM) S53 Set frequency write (RAM) S54 Set frequency write (EEPROM) S55 Inverter reset S56 Alarm definition batch clear S57 All parameter clear S58 Link parameter expansion setting S59 Second parameter changing [S-SigDataEnd] [SL-SigData] SL01 Output frequency[speed] SL51 Set frequency read (RAM) SL52 Set frequency read (EEPROM) SL53 Set frequency write (RAM) SL54 Set frequency write (EEPROM) [SL-SigDataEnd]