Series: FR-S500 DataFormat=Dec [P-SigData] 000 Torque boost 001 Maximum frequency 002 Minimum frequency 003 Base frequency 004 Multi-speed setting (high speed) 005 Multi-speed setting (middle speed) 006 Multi-speed setting (low speed) 007 Acceleration time 008 Deceleration time 009 Electronic thermal O/L relay 010 DC injection brake operation frequency 011 DC injection brake operation time 012 DC injection brake voltage 013 Starting frequency 014 Load pattern selection 015 Jog frequency 016 Jog acceleration/deceleration time 017 RUN key rotation direction selection 019 Base frequency voltage 020 Acceleration/deceleration reference frequency 021 Stall prevention function selection 022 Stall prevention operation level 023 Stall prevention operation level compensation factor at double speed 024 Multi-speed setting (speed 4) 025 Multi-speed setting (speed 5) 026 Multi-speed setting (speed 6) 027 Multi-speed setting (speed 7) 028 Stall prevention operation reduction starting frequency 029 Acceleration/deceleration pattern 030 Extended function display selection 031 Frequency jump 1A 032 Frequency jump 1B 033 Frequency jump 2A 034 Frequency jump 2B 035 Frequency jump 3A 036 Frequency jump 3B 037 Speed display 038 Frequency setting voltage gain frequency 039 Frequency setting current gain frequency 040 Start-time ground fault detection selection 041 Up-to-frequency sensitivity 042 Output frequency detection 043 Output frequency detection for reverse rotation 044 Second acceleration/deceleration time 045 Second deceleration time 046 Second torque boost 047 Second V/F (base frequency) 048 Output current detection level 049 Output current detection signal delay time 050 Zero current detection level 051 Zero current detection time 052 Control panel display data selection 053 Frequency setting operation selection 054 FM (AM) terminal function selection 055 Frequency monitoring reference 056 Current monitoring reference 057 Restart coasting time 058 Restart cushion time 059 Remote setting function selection/Frequency setting storage function selection 060 RL terminal function selection 061 RM terminal function selection 062 RH terminal function selection 063 STR terminal function selection 064 RUN terminal function selection 065 A, B, C terminal function selection 066 Retry selection 067 Number of retries at alarm occurrence 068 Retry waiting time 069 Retry count display erase 070 Soft-PWM setting 071 Applied motor 072 PWM frequency selection 073 0-5V/0-10V selection 074 Input filter time constant 075 Reset selection/PU stop selection 076 Cooling fan operation selection 077 Parameter write disable selection 078 Reverse rotation prevention selection 079 Operation mode selection 080 Multi-speed setting (speed 8) 081 Multi-speed setting (speed 9) 082 Multi-speed setting (speed 10) 083 Multi-speed setting (speed 11) 084 Multi-speed setting (speed 12) 085 Multi-speed setting (speed 13) 086 Multi-speed setting (speed 14) 087 Multi-speed setting (speed 15) 088 PID action selection 089 PID proportional band 090 PID integral time 091 PID upper limit 092 PID lower limit 093 PID action set point for PU operation 094 PID differential time 095 Rated motor slip 096 Slip compensation time constant 097 Constant-output region slip compensation selection 098 Automatic torque boost selection (Motor capacity) 099 Motor primary resistance 145 (n13)PU display language 162 (H6)Automatic restart after instantaneous power failure selection 331 (n1)Communication station number 332 (n2)Communication speed 333 (n3)Stop bit length 334 (n4)Parity check presence/absence 335 (n5)Number of communication retries 336 (n6)Communication check time interval 337 (n7)Wait time setting 338 (n8)Operation command write 339 (n9)Speed command write 340 (n10)Link start mode selection 341 (n11)CR/LF selection 342 (n12)EEPROM write selection 343 (n18)Communication error count 344 (n19)Protocol selection 345 (n20)Communication error check time 346 (n21)Communication reset selection 503 (H1)Maintenance timer 504 (H2)Maintenance timer alarm output set time 555 (H3)Current average time 556 (H4)Data output mask time 557 (H5)Current average value monitor signal output reference current 559 (H7)Second electronic thermal O/L relay 560 (b1)Regenerative function selection 561 (b2)Special regenerative brake duty 562 (H9)Multi-speed reference frequency 900 (C1)FM terminal calibration 901 (C1)AM terminal calibration 902 (C2)Frequency setting voltage bias frequency/(C3)Frequency setting voltage bias 903 (C4)Frequency setting voltage gain 904 (C5)Frequency setting current bias frequency/(C6)Frequency setting current bias 905 (C7)Frequency setting current gain 990 (n14)PU buzzer sound control 991 (n15)PU contrast adjustment 992 (n16)PU main display screen data selection 993 (n17)PU disconnection detection/PU setting lock [P-SigDataEnd] [S-SigData] S00 Operation mode S01 Output frequency[speed] S02 Output current S43 Alarm definition (Latest Nos. 1&2) S44 Alarm definition (Latest Nos. 3&4) S48 Run command S48.01 Forward rotation (STF) S48.02 Reverse rotation (STR) S48.03 Low speed (RL) S48.04 Middle speed (RM) S48.05 High speed (RH) S50 Inverter status monitor S50.00 Inverter running (RUN) S50.01 Forward rotation S50.02 Reverse rotation S50.03 Up to frequency (SU) S50.04 Overload (OL) S50.06 Frequency detection (FU) S50.07 Alarm occurrence S51 Set frequency read (RAM) S52 Set frequency read (EEPROM) S53 Set frequency write (RAM) S54 Set frequency write (RAM,EEPROM) S55 Inverter reset S56 Alarm definition batch clear S57 All parameter clear S58 Link parameter expansion setting S59 Second parameter changing [S-SigDataEnd] [SL-SigData] SL01 Output frequency[speed] SL51 Set frequency read (RAM) SL52 Set frequency read (EEPROM) SL53 Set frequency write (RAM) SL54 Set frequency write (RAM,EEPROM) [SL-SigDataEnd]