Series: FR-V500(L) DataFormat=Dec [P-SigData] 000 Torque boost (manual) 001 Maximum speed (simple mode) 002 Minimum speed (simple mode) 003 Base frequency 004 Multi-speed setting (high speed) (simple mode) 005 Multi-speed setting (middle speed) (simple mode) 006 Multi-speed setting (low speed) (simple mode) 007 Acceleration time (simple mode) 008 Deceleration time (simple mode) 009 Electronic thermal O/L relay 010 DC injection brake operation speed 011 DC injection brake operation time 012 DC injection brake voltage 013 Starting speed 015 Jog speed setting 016 Jog acceleration/deceleration time 017 MRS input selection 019 Base frequency voltage 020 Acceleration/deceleration reference speed 021 Acceleration/deceleration time increments 022 Torque restriction level 024 Multi-speed setting (speed 4) 025 Multi-speed setting (speed 5) 026 Multi-speed setting (speed 6) 027 Multi-speed setting (speed 7) 028 Multi-speed input compensation 029 Acceleration/deceleration pattern 030 Regenerative function selection 031 Speed jump 1A 032 Speed jump 1B 033 Speed jump 2A 034 Speed jump 2B 035 Speed jump 3A 036 Speed jump 3B 037 Speed display 041 Up-to-speed sensitivity 042 Speed detection 043 Speed detection for reverse rotation 044 Second acceleration/deceleration time 045 Second deceleration time 050 Second speed detection 052 DU/PU main display data selection 053 PU level display data selection 054 DA1 terminal function selection 055 Speed monitoring reference 056 Current monitoring reference 057 Restart coasting time 058 Restart cushion time 059 Remote setting function selection 060 Intelligent mode selection 065 Retry selection 067 Number of retries at alarm occurrence 068 Retry waiting time 069 Retry count display erasure 070 Special regenerative brake duty 071 Applied motor 072 PWM frequency selection (simple mode) 073 Speed setting signal 075 Reset selection/disconnected PU detection/PU stop selection 077 Parameter write disable selection (simple mode) 078 Reverse rotation prevention selection 079 Operation mode selection (simple mode) 080 Motor capacity 081 Number of motor poles 082 Motor excitation current (no load current) 083 Rated motor voltage 084 Rated motor frequency 090 Motor constant R1 091 Motor constant R2 092 Motor constant L1 093 Motor constant L2 094 Motor constant X 095 Online auto tuning selection (simple mode) 096 Auto tuning setting/status 110 Third acceleration/deceleration time 111 Third deceleration time 116 Third speed detection 117 Communication station number 118 Communication speed 119 Stop bit length/data length 120 Parity check presence/absence 121 Number of communication retries 122 Communication check time interval 123 Waiting time setting 124 CR, LF presence/absence selection 128 PID action selection 129 PID proportional band 130 PID integral time 131 Upper limit 132 Lower limit 133 PID action set point for PU operation 134 PID differential time 140 Backlash acceleration stopping speed 141 Backlash acceleration stopping time 142 Backlash deceleration stopping speed 143 Backlash deceleration stopping time 144 Speed setting switchover 145 PU display language selection 150 Output current detection level 151 Output current detection period 152 Zero current detection level 153 Zero current detection period 156 Stall prevention operation selection 157 OL signal output timer 158 DA2 terminal function selection 160 Extended function selection (simple mode) 162 Automatic restart after instantaneous power failure selection 163 First cushion time for restart 164 First cushion voltage for restart 165 Restart current restriction level 171 Actual operation hour meter clear 180 DI1 terminal function selection 181 DI2 terminal function selection 182 DI3 terminal function selection 183 DI4 terminal function selection 187 STR terminal function selection 190 DO1 terminal function selection 191 DO2 terminal function selection 192 DO3 terminal function selection 195 A, B, C terminal function selection 232 Multi-speed setting (speed 8) 233 Multi-speed setting (speed 9) 234 Multi-speed setting (speed 10) 235 Multi-speed setting (speed 11) 236 Multi-speed setting (speed 12) 237 Multi-speed setting (speed 13) 238 Multi-speed setting (speed 14) 239 Multi-speed setting (speed 15) 240 Soft-PWM setting 244 Cooling fan operation selection 250 Stop selection 251 Output phase failure protection selection 252 Override bias 253 Override gain 261 Power failure stop selection 262 Subtracted speed at deceleration start 263 Subtraction starting speed 264 Power-failure deceleration time 1 265 Power-failure deceleration time 2 266 Power-failure deceleration time switchover speed 278 Brake opening speed 279 Brake opening current 280 Brake opening current detection time 281 Brake operation time at start 282 Brake operation speed 283 Brake operation time at stop 284 Deceleration detection function selection 285 Overspeed detection speed 286 Droop gain 287 Droop filter constant 288 Droop function activation selection 300 BCD input bias 301 BCD input gain 302 Binary input bias 303 Binary input gain 304 Digital input and analog compensation input enable/disable selection 305 Read timing operation selection 306 Analog output signal selection 307 Setting for zero analog output 308 Setting for maximum analog output 309 Analog output signal voltage/current switchover 310 Analog meter voltage output selection 311 Setting for zero analog meter voltage output 312 Setting for maximum analog meter voltage output 313 Y0 output selection 314 Y1 output selection 315 Y2 output selection 316 Y3 output selection 317 Y4 output selection 318 Y5 output selection 319 Y6 output selection 320 RA1 output selection 321 RA2 output selection 322 RA3 output selection 329 Digital input unit selection 330 RA0 output selection 331 Communication station number 332 Communication speed 333 Stop bit length 334 Parity check presence/absence 335 Number of communication retries 336 Communication check time interval 337 Waiting time setting 338 Operation command source 339 Speed command source 340 Link startup mode selection 341 CR/LF presence/absence selection 342 EEPROM write selection 345 DeviceNet address (lower) 346 DeviceNet baud rate (lower) 347 DeviceNet address (higher) 348 DeviceNet baud rate (higher) 350 Stop position command selection 351 Orientation switchover speed 356 Internal stop position command 357 In-position zone 359 Orientation encoder rotation direction 360 External position command selection 361 Position shift 362 Orientation position loop gain 369 Number of orientation encoder pulses 374 Overspeed detection level 380 Acceleration S pattern 1 381 Deceleration S pattern 1 382 Acceleration S pattern 2 383 Deceleration S pattern 2 384 Input pulse division scaling factor 385 Speed for zero input pulse 386 Speed for maximum input pulse 393 Orientation selection 394 Number of machine side gear teeth 395 Number of motor side gear teeth 396 Orientation speed gain (P term) 397 Orientation speed integral time 398 Orientation speed gain (D term) 399 Orientation deceleration ratio 400 DI11 terminal function selection 401 DI12 terminal function selection 402 DI13 terminal function selection 403 DI14 terminal function selection 404 DI15 terminal function selection 405 DI16 terminal function selection 406 High resolution analog input selection 407 Motor temperature detection filter 410 DO11 terminal function selection 411 DO12 terminal function selection 412 DO13 terminal function selection 413 Encoder pulse output division ratio 419 Position command source selection 420 Command pulse scaling factor numerator 421 Command pulse scaling factor denominator 422 Position loop gain 423 Position feed forward gain 424 Position command acceleration/deceleration time constant 425 Position feed forward command filter 426 In-position width 427 Excessive level error 428 Command pulse selection 429 Clear signal selection 430 Pulse monitor selection 432 Pulse train torque command bias 433 Pulse train torque command gain 434 IP address 1 435 IP address 2 436 IP address 3 437 IP address 4 438 Sub-net mask 1 439 Sub-net mask 2 440 Sub-net mask 3 441 Sub-net mask 4 442 Gateway address 1 443 Gateway address 2 444 Gateway address 3 445 Gateway address 4 446 Password 447 Digital torque command bias 448 Digital torque command gain 450 Second applied motor 451 Second motor control method selection 452 Second electronic thermal O/L relay 453 Second motor capacity 454 Number of second motor poles 464 Digital position control sudden stop deceleration time 465 First position feed amount lower 4 digits 466 First position feed amount upper 4 digits 467 Second position feed amount lower 4 digits 468 Second position feed amount upper 4 digits 469 Third position feed amount lower 4 digits 470 Third position feed amount upper 4 digits 471 Fourth position feed amount lower 4 digits 472 Fourth position feed amount upper 4 digits 473 Fifth position feed amount lower 4 digits 474 Fifth position feed amount upper 4 digits 475 Sixth position feed amount lower 4 digits 476 Sixth position feed amount upper 4 digits 477 Seventh position feed amount lower 4 digits 478 Seventh position feed amount upper 4 digits 479 Eighth position feed amount lower 4 digits 480 Eighth position feed amount upper 4 digits 481 Ninth position feed amount lower 4 digits 482 Ninth position feed amount upper 4 digits 483 Tenth position feed amount lower 4 digits 484 Tenth position feed amount upper 4 digits 485 Eleventh position feed amount lower 4 digits 486 Eleventh position feed amount upper 4 digits 487 Twelfth position feed amount lower 4 digits 488 Twelfth position feed amount upper 4 digits 489 Thirteenth position feed amount lower 4 digits 490 Thirteenth position feed amount upper 4 digits 491 Fourteenth position feed amount lower 4 digits 492 Fourteenth position feed amount upper 4 digits 493 Fifteenth position feed amount lower 4 digits 494 Fifteenth position feed amount upper 4 digits 495 Remote output selection 496 Remote output data 1 497 Remote output data 2 499 Action selection at SSCNET communication inter ruption (FR-V500 only) 500 Communication error recognition waiting time 501 Communication error occurence count display 502 Stop mode selection at communication error 520 Trace data CH1 (FR-V500L only) 521 Trace data CH2 (FR-V500L only) 522 Trace data CH3 (FR-V500L only) 523 Trace data CH4 (FR-V500L only) 524 Trace data CH5 (FR-V500L only) 525 Trace data CH6 (FR-V500L only) 526 Trace data CH7 (FR-V500L only) 527 Trace data CH8 (FR-V500L only) 528 Trace data CH9 (FR-V500L only) 529 Trace data CH10 (FR-V500L only) 530 Sampling cycle (FR-V500L only) 531 Number of sampling retries selection (FR-V500L only) 532 Trigger source selection 1 (FR-V500L only) 533 Trigger source selection 2 (FR-V500L only) 534 Trigger level (FR-V500L only) 535 Trigger slope selection (FR-V500L only) 536 Pre-trigger (FR-V500L only) 537 Trace data D/A output selection (FR-V500L only) 538 Trace Start/Stop selction (FR-V500L only) 591 Holding time at a start (FR-V500L only) 800 Control system selection (simple mode) 801 Torque characteristic selection 802 Pre-excitation selection 803 Constant output region torque characteristic selection 804 Torque command source selection 805 Torque command source (RAM) 806 Torque command source (RAM, EEPROM) 807 Speed restriction selection 808 Forward rotation speed restriction 809 Reverse rotation speed restriction 810 Torque restriction input method selection 812 Torque restriction level (regeneration) 813 Torque restriction level (3rd quadrant) 814 Torque restriction level (4th quadrant) 815 Torque restriction level 2 816 Acceleration torque restriction level 817 Deceleration torque restriction level 818 Easy gain tuning response level setting (simple mode) 819 Easy gain tuning selection (simple mode) 820 Speed control P gain 1 821 Speed control integral time 1 822 Speed setting filter 1 823 Speed detection filter 1 824 Torque control P gain 1 825 Torque control integral time 1 826 Torque setting filter 1 827 Torque detection filter 1 828 Model speed control gain 830 Speed control P gain 2 831 Speed control integral time 2 832 Speed setting filter 2 833 Speed detection filter 2 834 Torque control P gain 2 835 Torque control integral time 2 836 Torque setting filter 2 837 Torque detection filter 2 840 Torque bias selection 841 Torque bias 1 842 Torque bias 2 843 Torque bias 3 844 Torque bias filter 845 Torque bias operation time 846 Torque bias balance compensation 847 Fall-time torque bias No. 3 bias 848 Fall-time torque bias No. 3 gain 849 Analog input offset adjustment 851 Number of encoder pulses 852 Encoder rotation direction 854 Excitation ratio 859 Torque current 862 Notch filter frequency 863 Notch filter depth 864 Torque detection 865 Low speed detection 866 Torque monitoring reference 867 DA1 output filter 868 No. 1 terminal function assignment 870 Speed deviation level 871 Speed deviation time 873 Speed restriction 874 OLT level setting 875 Fault definition 876 Thermal relay protector input 877 Speed feed forward/model adaptive speed control selection 878 Speed feed forward filter 879 Speed feed forward torque restriction 880 Load inertia ratio 881 Speed feed forward gain 890 Maintenance output setting time 891 Maintenance output timer 892 Maintenance output signal clear 900 DA1 terminal calibration 901 DA2 terminal calibration 902 Speed setting No. 2 bias 903 Speed setting No. 2 gain 904 Torque command No. 3 bias 905 Torque command No. 3 gain 917 No. 1 terminal bias (speed) 918 No. 1 terminal gain (speed) 919 No. 1 terminal bias (torque/magnetic flux) 920 No. 1 terminal gain (torque/magnetic flux) 925 Motor temperature detection calibration 926 No. 6 terminal bias (speed) 927 No. 6 terminal gain (speed) 928 No. 6 terminal bias (torque) 929 No. 6 terminal gain (torque) 990 PU buzzer control 991 PU contrast adjustment [P-SigDataEnd] [SL-SigData] SL00 Operation mode SL01 Speed SL02 Output current SL03 Output voltage SL04 Special monitor SL05 Special monitor selection No. SL06 Output frequency SL07 Output current SL08 Output voltage SL09 Speed setting SL10 Running speed SL11 Motor torque SL12 Converter output voltage SL13 Regenerative brake SL14 Electronic thermal relay function load factor SL15 Output current peak value SL16 Converter output voltage peak value SL19 Input terminal status SL19.00 STF SL19.01 STR SL19.02 DI1 SL19.03 DI2 SL19.04 DI3 SL19.05 DI4 SL19.06 OH SL19.07 RES SL20 Output terminal status SL20.00 DO1 SL20.01 DO2 SL20.02 DO3 SL20.03 ABC SL21 Load meter SL22 Motor excitation current SL23 Position pulse SL24 Cumulative energization time SL26 Actual operation time SL27 Motor load factor SL29 Torque command SL30 Torque current command SL31 Motor output SL32 Feedback pulse SL43 Alarm definition (Latest Nos. 1&2) SL44 Alarm definition (Latest Nos. 3&4) SL45 Alarm definition (Latest Nos. 5&6) SL46 Alarm definition (Latest Nos. 7&8) SL48 Run command SL48.01 Forward rotation (STF) SL48.02 Reverse rotation (STR) SL48.03 Low speed (RL/DI1) (FR-A5NR only) SL48.04 Middle speed (RM/DI2) (FR-A5NR only) SL48.05 High speed (RH/DI3) (FR-A5NR only) SL48.06 Second function selection (RT/DI4) (FR-A5NR only) SL50 Inverter status monitor SL50.00 Inverter running (RUN) SL50.01 Forward rotation SL50.02 Reverse rotation SL50.03 DO1 (Inverter) SL50.03 Inverter running (RUN/DO1) (FR-A5NR) SL50.04 DO2 (Inverter) SL50.04 Up to speed (SU/DO2) (FR-A5NR) SL50.05 DO3 (Inverter) SL50.05 Instantaneous power failure (IPF/DO3) (FR-A5NR) SL50.06 Speed detection (FB) SL50.07 Alarm occurrence SL51 Set speed read (RAM) SL52 Set speed read (EEPROM) SL53 Set speed write (RAM) SL54 Set speed write (EEPROM) SL55 Inverter reset SL56 Alarm definition all clear SL57 Parameter all clear SL58 Link parameter expansion setting SL59 Second parameter changing [SL-SigDataEnd]