//E5_N MaxSigCnt=148 DataFormat=Hex [C0-SigData] C00000 PV C00001 Status C00002 Internal set point C00003 Heater current 1 value monitor C00004 MV monitor (heating) C00005 MV monitor (cooling) C00006 Heater current value 2 monitor C00007 Leakage current value 1 monitor C00008 Leakage current value 2 monitor C00009 Soak time remain monitor [C0-SigDataEnd] [C1-SigData] C10000 Operation/adjustment protect C10001 Initial setting/communications protect C10002 Setup change protection C10003 Set point C10004 Alarm value 1 C10005 Upper-limit alarm 1 C10006 Lower-limit alarm 1 C10007 Alarm value 2 C10008 Upper-limit alarm 2 C10009 Lower-limit alarm 2 C1000A Alarm value 3 C1000B Upper-limit alarm value 3 C1000C Lower-limit alarm value 3 C1000D Heater burnout 1 detection C1000E Set point 0 C1000F Set point 1 C10010 Set point 2 C10011 Set point 3 C10012 Temperature input shift value C10013 Upper-limit temperature input shift value C10014 Lower-limit temperature input shift value C10015 Proportional band C10016 Integral time C10017 Derivative time C10018 Cooling coefficient C10019 Dead band C1001A Manual reset value C1001B Hysteresis (heating) C1001C Hysteresis (cooling) C1001D Heater burnout 2 detection C1001E HS alarm 1 C1001F HS alarm 2 C10020 Soak time C10021 Wait band C10022 MV at stop C10023 MV at PV error C10024 Manual manipulated variable C10025 SP ramp set value C10026 MV upper limit C10027 MV lower limit C10028 Move protect level C10029 Password to move to protect level C1002A Parameter mask enable [C1-SigDataEnd] [C3-SigData] C30000 Input type C30001 Scaling upper limit C30002 Scaling lower limit C30003 Decimal point position C30004 Temperature unit C30005 SP upper limit C30006 SP lower limit C30007 PID/OnOff C30008 Standard or heating and cooling C30009 ST C3000A Control period (heat) C3000B Control period (cool) C3000C Direct/reverse operation C3000D Alarm 1 type C3000E Alarm 2 type C3000F Alarm 3 type C30010 Communications unit number C30011 Communications baud rate C30012 Communications data length C30013 Communications stop bits C30014 Communications parity C30015 Number of multi-SP uses C30016 Event input assignment 1 C30017 Event input assignment 2 C3001A Multi-SP usage C3001B SP ramp time unit C3001C SP ramp set value C3001D Standby sequence reset C3001E Alarm 1 open in alarm C3001F Alarm 1 hysteresis C30020 Alarm 2 open in alarm C30021 Alarm 2 hysteresis C30022 Alarm 3 open in alarm C30023 Alarm 3 hysteresis C30024 HB ON/OFF C30025 Heater burnout latch C30026 Heater burnout hysteresis C30027 ST stable range C30028 Alpha C30029 MV upper limit C3002A MV lower limit C3002B Input digital filter C3002C Additional PV display C3002D MV display C3002E Automatic display return time C3002F Alarm 1 latch C30030 Alarm 2 latch C30031 Alarm 3 latch C30032 Protect level move time C30033 Input error output C30034 Cold junction compensation method C30035 MB command logic switching C30036 PV change color C30037 PV stable band C30038 Alarm 1 ON delay C30039 Alarm 2 ON delay C3003A Alarm 3 ON delay C3003B Alarm 1 OFF delay C3003C Alarm 2 OFF delay C3003D Alarm 3 OFF delay C3003E Transfer output type C3003F Transfer output upper limit C30040 Transfer output lower limit C30041 Linear current output C30042 Input shift type C30043 MV at stop and error addition C30044 Auto/manual switching display addition C30045 RT C30046 HS alarm C30047 HS alarm latch C30048 HS alarm hysteresis C30049 LBA detection time C3004A LBA level C3004B LBA band C3004C Protocol Setting C3004D Send data wait time C3004E Control output 1 assignment C3004F Control output 2 assignment C30050 Alarm 1 assignment C30051 Alarm 2 assignment C30052 Display character switch C30053 Program pattern C30054 Soak time units C30055 Alarm SP selection C30056 Alarm 3 assignment [C3-SigDataEnd] [A-SigData] A0000 Communications writing A0001 RUN/STOP A0002 Multi-SP A0003 AT execute/cancel A0004 Write mode A0005 Save RAM data A0006 Software reset A0007 Move to setup area 1 A0008 Move to protect level A0009 Auto/manual switch A000B Parameter initialization A0011 Program start [A-SigDataEnd] [C0-SigData]-B C00000 PV C00001.00 Heater overcurrent (CT1) C00001.01 Heater current hold (CT1) C00001.02 HB (heater burnout) error C00001.03 HS alarm output (CT1) C00001.05 Display range exceeded C00001.06 Input error C00001.08 Control output (heating) C00001.09 Control output (cooling) C00001.10 HB (heater burnout) alarm output (CT1) C00001.11 HB (heater burnout) alarm output (CT2) C00001.12 Alarm output 1 C00001.13 Alarm output 2 C00001.14 Alarm output 3 C00001.15 Program end output C00001.16 Event input 1 C00001.17 Event input 2 C00001.20 Write mode C00001.21 EEPROM C00001.22 Setup area C00001.23 AT execute/cancel C00001.24 RUN/STOP C00001.25 Communications writing C00001.26 Auto/manual switch C00001.28 Heater overcurrent (CT2) C00001.29 Heater current hold (CT2) C00001.31 HS alarm output (CT2) C00002 Internal set point C00003 Heater current 1 value monitor C00004 MV monitor (heating) C00005 MV monitor (cooling) C00006 Heater current value 2 monitor C00007 Leakage current value 1 monitor C00008 Leakage current value 2 monitor C00009 Soak time remain monitor [C0-SigDataEnd]-B