Name=PLC1 SRV MaxSigCnt=169 DataFormat=Hex [SigData] 0000 Measured value (PV) CH1 0001 Comprehensive event state CH1 0001.0 Burnout CH1 0001.1 Event 1 state CH1 0001.2 Event 2 state CH1 0001.3 Heater break alarm state CH1 0001.4 Control loop break alarm (LBA) state CH1 0002 Heat-side manipulated output value CH1 0003 Set value monitor CH1 0004 Error code (Data of each module) 0004.0 Memory backup error 0004.3 Adjustment data error 0004.4 Input error 0004.5 Current transformer input error 0004.6 Temperature compensation error 0005 Cool-side manipulated output value CH1 0006 Current transformer input measured value CH1 0008 Burnout state CH1 0009 Event 1 state CH1 000A Event 2 state CH1 000B Heater break alarm (HBA) state CH1 000C Control loop break alarm (LBA) state CH1 000D Temperature rise completion state CH1 000F Operation mode CH1 0010 Set value (SV) CH1 0011 Heat-side proportional band CH1 0012 Integral time CH1 0013 Derivative time CH1 0014 Control response parameter CH1 0015 PV bias CH1 0016 Event 1 set value CH1 0017 Event 2 set value CH1 001C Cool-side proportional band CH1 001E Overlap/Deadband CH1 001F Setting change rate limiter CH1 0020 PID/AT transfer 0021 Auto/Manual transfer CH1 0022 Manual output value CH1 0023 Output limiter (high) CH1 0024 Output limiter (low) CH1 0025 Heat-side proportional cycle time CH1 0026 Cool-side proportional cycle time CH1 0027 Digital filter CH1 0028 Heater break alarm (HBA) set value CH1 0029 Number of heater break alarm (HBA) delay times CH1 0030 Control RUN/STOP transfer (Data of each module) 0031 Input error determination point (high) CH1 0032 Input error determination point (low) CH1 0033 Action at input error (high) CH1 0034 Action at input error (low) CH1 0035 Manipulated output value at input error CH1 0036 AT differential gap time CH1 0038 AT bias CH1 003C Event LED mode setting (Data of each module) 003D DI set (Data of each module) 003E DI status (Data of each module) 003F DO1 set (Data of each module) 0040 DO2 set (Data of each module) 0041 DO status (Data of each module) 0042 Event interlock release (Data of each module) 0043 Temperature rise completion zone CH1 0044 Temperature rise completion soak time CH1 0859 Control loop break alarm (LBA) use selection CH1 085A Control loop break alarm (LBA) time CH1 085B Control loop break alarm (LBA) deadband CH1 0860 Initial setting mode (Data of each module) 0870 Input range number CH1 0871 Input scale high limit CH1 0872 Input scale low limit CH1 0873 Input range decimal point position CH1 0874 Temperature unit selection CH1 0875 Control type selection CH1 0876 ON/OFF control differential gap (upper) CH1 0877 ON/OFF control differential gap (lower) CH1 0878 Event 1 differential gap CH1 0879 Event 2 differential gap CH1 087A Event 1 type selection CH1 087B Event 2 type selection CH1 087C Event 1 action selection CH1 087C.0 Hold action CH1 087C.1 Re-hold action CH1 087C.2 Interlock operation CH1 087C.3 Event action at input error CH1 087C.4 Hold action at control start CH1 087D Event 2 action CH1 087D.0 Hold action CH1 087D.1 Re-hold action CH1 087D.2 Interlock operation CH1 087D.3 Event action at input error CH1 087D.4 Hold action at control start CH1 087E Event delay timer CH1 087F Transmission transfer time setting (Data of each module) 0881 Operation mode holding setting (Data of each module) 1000 Measured value (PV) CH2 1001 Comprehensive event state CH2 1001.0 Burnout CH2 1001.1 Event 1 state CH2 1001.2 Event 2 state CH2 1001.3 Heater break alarm state CH2 1001.4 Control loop break alarm (LBA) state CH2 1002 Heat-side manipulated output value CH2 1003 Set value monitor CH2 1005 Cool-side manipulated output value CH2 1006 Current transformer input measured value CH2 1008 Burnout state CH2 1009 Event 1 state CH2 100A Event 2 state CH2 100B Heater break alarm (HBA) state CH2 100C Control loop break alarm (LBA) state CH2 100D Temperature rise completion state CH2 100F Operation mode CH2 1010 Set value (SV) CH2 1011 Heat-side proportional band CH2 1012 Integral time CH2 1013 Derivative time CH2 1014 Control response parameter CH2 1015 PV bias CH2 1016 Event 1 set value CH2 1017 Event 2 set value CH2 101C Cool-side proportional band CH2 101E Overlap/Deadband CH2 101F Setting change rate limiter CH2 1020 PID/AT transfer 1021 Auto/Manual transfer CH2 1022 Manual output value CH2 1023 Output limiter (high) CH2 1024 Output limiter (low) CH2 1025 Heat-side proportional cycle time CH2 1026 Cool-side proportional cycle time CH2 1027 Digital filter CH2 1028 Heater break alarm (HBA) set value CH2 1029 Number of heater break alarm (HBA) delay times CH2 1031 Input error determination point (high) CH2 1032 Input error determination point (low) CH2 1033 Action at input error (high) CH2 1034 Action at input error (low) CH2 1035 Manipulated output value at input error CH2 1036 AT differential gap time CH2 1038 AT bias CH2 1043 Temperature rise completion zone CH2 1044 Temperature rise completion soak time CH2 1859 Control loop break alarm (LBA) use selection CH2 185A Control loop break alarm (LBA) time CH2 185B Control loop break alarm (LBA) deadband CH2 1870 Input range number CH2 1871 Input scale high limit CH2 1872 Input scale low limit CH2 1873 Input range decimal point position CH2 1874 Temperature unit selection CH2 1875 Control type selection CH2 1876 ON/OFF control differential gap (upper) CH2 1877 ON/OFF control differential gap (lower) CH2 1878 Event 1 differential gap CH2 1879 Event 2 differential gap CH2 187A Event 1 type CH2 187B Event 2 type CH2 187C Event 1 action CH2 187C.0 Standby operation CH2 187C.1 Re-standby operation CH2 187C.2 Interlock operation CH2 187C.3 Event in input error CH2 187C.4 Standby operation when beginning to control CH2 187D Event 2 action CH2 187D.0 Standby operation CH2 187D.1 Re-standby operation CH2 187D.2 Interlock operation CH2 187D.3 Event in input error CH2 187D.4 Standby operation when beginning to control CH2 187E Event delay timer CH2 [SigDataEnd]