Name=PLC1 SRZ MaxSigCnt= DataFormat=Hex [SigData] 0000 Error code (Z-COM module) 0000.0 SRAM error/Adjustment data error (Error code (Z-COM module)) 0000.1 Data back-up error (Error code (Z-COM module)) 0000.2 A/D conversion error (Error code (Z-COM module)) 0000.5 Logic output data error (Error code (Z-COM module)) 0000.6 Stack overflow (Error code (Z-COM module)) 0001-0064 Error code (Function module) CH1-CH100 0001.0-0064.0 Adjustment data error (Error code (Function module)) CH1-CH100 0001.1-0064.1 Data back-up error (Error code (Function module)) CH1-CH100 0001.2-0064.2 A/D conversion error (Error code (Function module)) CH1-CH100 0001.5-0064.5 Logic output data error (Error code (Function module)) CH1-CH100 0065 Backup memory state monitor (Z-COM module) 0066-00C9 Backup memory state monitor (Function module) CH1-CH100 00CA System communication state 00CA.0 Data collection condition 00CB SRZ normal communication flag 00CC PLC communication error code 00CC.0 PLC register read/write error (PLC communication error code) 00CC.1 Slave communication timeout (PLC communication error code) 00CC.3 Internal communication error (PLC communication error code) 00CC.4 Master communication timeout (PLC communication error code) 00CD Unit recognition flag 00CD.0 SRZ unit 1 (Unit recognition flag) 00CD.1 SRZ unit 2 (Unit recognition flag) 00CD.2 SRZ unit 3 (Unit recognition flag) 00CD.3 SRZ unit 4 (Unit recognition flag) 0132 Monitor for the number of connected modules 0133 RUN/STOP transfer (Each unit) 0134-0197 RUN/STOP transfer (Each module) CH1-CH100 0198-01FB Control RUN/STOP holding setting (Each module) CH1-CH100 01FC-023B Measured value (PV) CH1-CH64 023C-027B Comprehensive event state CH1-CH64 023C.0-027B.0 Event 1 (Comprehensive event state) CH1-CH64 023C.1-027B.1 Event 2 (Comprehensive event state) CH1-CH64 023C.2-027B.2 Event 3 (Comprehensive event state) CH1-CH64 023C.3-027B.3 Event 4 (Comprehensive event state) CH1-CH64 023C.4-027B.4 Heater break alarm (Comprehensive event state) CH1-CH64 023C.5-027B.5 Temperature rise completion (Comprehensive event state) CH1-CH64 023C.6-027B.6 Burnout (Comprehensive event state) CH1-CH64 027C-02BB Operation mode state monitor CH1-CH64 027C.0-02BB.0 Control STOP (Operation mode state monitor) CH1-CH64 027C.1-02BB.1 Control RUN (Operation mode state monitor) CH1-CH64 027C.2-02BB.2 Manual mode (Operation mode state monitor) CH1-CH64 027C.3-02BB.3 Remote mode (Operation mode state monitor) CH1-CH64 02CC-030B Manipulated output value (MV) monitor [heat-side] CH1-CH64 030C-034B Manipulated output value (MV) monitor [cool-side] CH1-CH64 034C-038B Current transformer (CT) input value monitor CH1-CH64 038C-03CB Set value (SV) monitor CH1-CH64 03CC-040B Remote setting (RS) input value monitor CH1-CH64 040C-044B Burnout state monitor CH1-CH64 044C-048B Event 1 state monitor CH1-CH64 048C-04CB Event 2 state monitor CH1-CH64 04CC-050B Event 3 state monitor CH1-CH64 050C-054B Event 4 state monitor CH1-CH64 054C-058B Heater break alarm (HBA) state monitor CH1-CH64 058C-059B Output state monitor CH1-CH16 058C.0-059B.0 OUT1 (Output state monitor) CH1-CH16 058C.1-059B.1 OUT2 (Output state monitor) CH1-CH16 058C.2-059B.2 OUT3 (Output state monitor) CH1-CH16 058C.3-059B.3 OUT4 (Output state monitor) CH1-CH16 059C-05DB Memory area soak time monitor CH1-CH64 05EC-062B Holding peak value ambient temperature monitor CH1-CH64 063C-064B Logic output monitor 1 CH1-CH16 063C.0-064B.0 Logic output 1 (Logic output monitor 1) CH1-CH16 063C.1-064B.1 Logic output 2 (Logic output monitor 1) CH1-CH16 063C.2-064B.2 Logic output 3 (Logic output monitor 1) CH1-CH16 063C.3-064B.3 Logic output 4 (Logic output monitor 1) CH1-CH16 063C.4-064B.4 Logic output 5 (Logic output monitor 1) CH1-CH16 063C.5-064B.5 Logic output 6 (Logic output monitor 1) CH1-CH16 063C.6-064B.6 Logic output 7 (Logic output monitor 1) CH1-CH16 063C.7-064B.7 Logic output 8 (Logic output monitor 1) CH1-CH16 080C-084B PID/AT transfer CH1-CH64 084C-088B Auto/Manual transfer CH1-CH64 088C-08CB Remote/Local transfer CH1-CH64 08DC-091B Memory area transfer CH1-CH64 091C-095B Interlock release CH1-CH64 095C-099B Event 1 set value (EV1) CH1-CH64 099C-09DB Event 2 set value (EV2) CH1-CH64 09DC-0A1B Event 3 set value (EV3) CH1-CH64 0A1C-0A5B Event 4 set value (EV4) CH1-CH64 0A5C-0A9B Control loop break alarm (LBA) time CH1-CH64 0A9C-0ADB LBA deadband CH1-CH64 0ADC-0B1B Set value (SV) CH1-CH64 0B1C-0B5B Proportional band [heat-side] CH1-CH64 0B5C-0B9B Integral time [heat-side] CH1-CH64 0B9C-0BDB Derivative time [heat-side] CH1-CH64 0BDC-0C1B Control response parameter CH1-CH64 0C1C-0C5B Proportional band [cool-side] CH1-CH64 0C5C-0C9B Integral time [cool-side] CH1-CH64 0C9C-0CDB Derivative time [cool-side] CH1-CH64 0CDC-0D1B Overlap/Deadband CH1-CH64 0D1C-0D5B Manual reset CH1-CH64 0D5C-0D9B Setting change rate limiter (up) CH1-CH64 0D9C-0DDB Setting change rate limiter (down) CH1-CH64 0DDC-0E1B Area soak time CH1-CH64 0E1C-0E5B Link area number CH1-CH64 0E5C-0E9B Heater break alarm (HBA) set value CH1-CH64 0E9C-0EDB Heater break determination point CH1-CH64 0EDC-0F1B Heater melting determination point CH1-CH64 0F1C-0F5B PV bias CH1-CH64 0F5C-0F9B PV digital filter CH1-CH64 0F9C-0FDB PV ratio CH1-CH64 0FDC-101B PV low input cut-off CH1-CH64 101C-105B RS bias CH1-CH64 105C-109B RS digital filter CH1-CH64 109C-10DB RS ratio CH1-CH64 10DC-111B Output distribution selection CH1-CH64 111C-115B Output distribution bias CH1-CH64 115C-119B Output distribution ratio CH1-CH64 119C-11DB Proportional cycle time CH1-CH64 11DC-121B Minimum ON/OFF time of proportioning cycle CH1-CH64 121C-125B Manual manipulated output value CH1-CH64 125C-129B Area soak time stop function CH1-CH64 129C-12DB EDS mode (for disturbance 1) CH1-CH64 12DC-131B EDS mode (for disturbance 2) CH1-CH64 131C-135B EDS value 1 (for disturbance 1) CH1-CH64 135C-139B EDS value 1 (for disturbance 2) CH1-CH64 139C-13DB EDS value 2 (for disturbance 1) CH1-CH64 13DC-141B EDS value 2 (for disturbance 2) CH1-CH64 141C-145B EDS transfer time (for disturbance 1) CH1-CH64 145C-149B EDS transfer time (for disturbance 2) CH1-CH64 149C-14DB EDS action time (for disturbance 1) CH1-CH64 14DC-151B EDS action time (for disturbance 2) CH1-CH64 151C-155B EDS action wait time (for disturbance 1) CH1-CH64 155C-159B EDS action wait time (for disturbance 2) CH1-CH64 159C-15DB EDS value learning times CH1-CH64 15DC-161B EDS start signal CH1-CH64 161C-165B Operation mode CH1-CH64 165C-169B Startup tuning (ST) CH1-CH64 169C-16DB Automatic temperature rise learning CH1-CH64 16DC-16EB Communication switch for logic CH1-CH16 16DC.0-16EB.0 Communication switch 1 (Communication switch for logic) CH1-CH16 16DC.1-16EB.1 Communication switch 2 (Communication switch for logic) CH1-CH16 16DC.2-16EB.2 Communication switch 3 (Communication switch for logic) CH1-CH16 16DC.3-16EB.3 Communication switch 4 (Communication switch for logic) CH1-CH16 196C-19AB Input type CH1-CH64 19AC-19EB Display unit CH1-CH64 19EC-1A2B Decimal point position CH1-CH64 1A2C-1A6B Input scale high CH1-CH64 1A6C-1AAB Input scale low CH1-CH64 1AAC-1AEB Input error determination point (high) CH1-CH64 1AEC-1B2B Input error determination point (low) CH1-CH64 1B2C-1B6B Burnout direction CH1-CH64 1B6C-1BAB Square root extraction CH1-CH64 1BAC-1BEB Output assignment (Logic output selection function) CH1-CH64 1BEC-1C2B Energized/ De-energized (Logic output selection function) CH1-CH64 1C2C-1C6B Event 1 type CH1-CH64 1C6C-1CAB Event 1 channel setting CH1-CH64 1CAC-1CEB Event 1 hold action CH1-CH64 1CEC-1D2B Event 1 interlock CH1-CH64 1D2C-1D6B Event 1 differential gap CH1-CH64 1D6C-1DAB Event 1 delay timer CH1-CH64 1DAC-1DEB Force ON of Event 1 action CH1-CH64 1DAC.0-1DEB.0 Event output turned on at input error occurrence (Force ON of Event 1 action) CH1-CH64 1DAC.1-1DEB.1 Event output turned on in manual mode (Force ON of Event 1 action) CH1-CH64 1DAC.2-1DEB.2 Event output turned on during the autotuning (AT) function is being executed (Force ON of Event 1 action) CH1-CH64 1DAC.3-1DEB.3 Event output turned on during the setting change rate limiter is being operated (Force ON of Event 1 action) CH1-CH64 1DEC-1E2B Event 2 type CH1-CH64 1E2C-1E6B Event 2 channel setting CH1-CH64 1E6C-1EAB Event 2 hold action CH1-CH64 1EAC-1EEB Event 2 interlock CH1-CH64 1EEC-1F2B Event 2 differential gap CH1-CH64 1F2C-1F6B Event 2 delay timer CH1-CH64 1F6C-1FAB Force ON of Event 2 action CH1-CH64 1F6C.0-1FAB.0 Event output turned on at input error occurrence (Force ON of Event 2 action) CH1-CH64 1F6C.1-1FAB.1 Event output turned on in manual mode (Force ON of Event 2 action) CH1-CH64 1F6C.2-1FAB.2 Event output turned on during the autotuning (AT) function is being executed (Force ON of Event 2 action) CH1-CH64 1F6C.3-1FAB.3 Event output turned on during the setting change rate limiter is being operated (Force ON of Event 2 action) CH1-CH64 1FAC-1FEB Event 3 type CH1-CH64 1FEC-202B Event 3 channel setting CH1-CH64 202C-206B Event 3 hold action CH1-CH64 206C-20AB Event 3 interlock CH1-CH64 20AC-20EB Event 3 differential gap CH1-CH64 20EC-212B Event 3 delay timer CH1-CH64 212C-216B Force ON of Event 3 action CH1-CH64 212C.0-216B.0 Event output turned on at input error occurrence (Force ON of Event 3 action) CH1-CH64 212C.1-216B.1 Event output turned on in manual mode (Force ON of Event 3 action) CH1-CH64 212C.2-216B.2 Event output turned on during the autotuning (AT) function is being executed (Force ON of Event 3 action) CH1-CH64 212C.3-216B.3 Event output turned on during the setting change rate limiter is being operated (Force ON of Event 3 action) CH1-CH64 216C-21AB Event 4 type CH1-CH64 21AC-21EB Event 4 channel setting CH1-CH64 21EC-222B Event 4 hold action CH1-CH64 222C-226B Event 4 interlock CH1-CH64 226C-22AB Event 4 differential gap CH1-CH64 22AC-22EB Event 4 delay timer CH1-CH64 22EC-232B Force ON of Event 4 action CH1-CH64 22EC.0-232B.0 Event output turned on at input error occurrence (Force ON of Event 4 action) CH1-CH64 22EC.1-232B.1 Event output turned on in manual mode (Force ON of Event 4 action) CH1-CH64 22EC.2-232B.2 Event output turned on during the autotuning (AT) function is being executed (Force ON of Event 4 action) CH1-CH64 22EC.3-232B.3 Event output turned on during the setting change rate limiter is being operated (Force ON of Event 4 action) CH1-CH64 232C-236B CT ratio CH1-CH64 236C-23AB CT assignment CH1-CH64 23AC-23EB Heater break alarm (HBA) type CH1-CH64 23EC-242B Number of heater break alarm (HBA) delay times CH1-CH64 242C-246B Hot/Cold start CH1-CH64 246C-24AB Start determination point CH1-CH64 24AC-24EB SV tracking CH1-CH64 24EC-252B MV transfer function [Action taken when changed to Manual mode from Auto mode] CH1-CH64 252C-256B Control action CH1-CH64 256C-25AB Integral/derivative time decimal point position CH1-CH64 25AC-25EB Derivative action CH1-CH64 25EC-262B Undershoot suppression factor CH1-CH64 262C-266B Derivative gain CH1-CH64 266C-26AB ON/OFF action differential gap (upper) CH1-CH64 26AC-26EB ON/OFF action differential gap (lower) CH1-CH64 26EC-272B Action (high) at input error CH1-CH64 272C-276B Action (low) at input error CH1-CH64 276C-27AB Manipulated output value at input error CH1-CH64 27AC-27EB Manipulated output value at STOP mode [heat-side] CH1-CH64 27EC-282B Manipulated output value at STOP mode [cool-side] CH1-CH64 282C-286B Output change rate limiter (up) [heat-side] CH1-CH64 286C-28AB Output change rate limiter (down) [heat-side] CH1-CH64 28AC-28EB Output limiter (high) [heat-side] CH1-CH64 28EC-292B Output limiter (low) [heat-side] CH1-CH64 292C-296B Output change rate limiter (up) [cool-side] CH1-CH64 296C-29AB Output change rate limiter (down) [cool-side] CH1-CH64 29AC-29EB Output limiter (high) [cool-side] CH1-CH64 29EC-2A2B Output limiter (low) [cool-side] CH1-CH64 2A2C-2A6B AT bias CH1-CH64 2A6C-2AAB AT cycles CH1-CH64 2AAC-2AEB Output value with AT turned on CH1-CH64 2AEC-2B2B Output value with AT turned off CH1-CH64 2B2C-2B6B AT differential gap time CH1-CH64 2B6C-2BAB Proportional band adjusting factor [heat-side] CH1-CH64 2BAC-2BEB Integral time adjusting factor [heat-side] CH1-CH64 2BEC-2C2B Derivative time adjusting factor [heat-side] CH1-CH64 2C2C-2C6B Proportional band adjusting factor [cool-side] CH1-CH64 2C6C-2CAB Integral time adjusting factor [cool-side] CH1-CH64 2CAC-2CEB Derivative time adjusting factor [cool-side] CH1-CH64 2CEC-2D2B Proportional band limiter (high) [heat-side] CH1-CH64 2D2C-2D6B Proportional band limiter (low) [heat-side] CH1-CH64 2D6C-2DAB Integral time limiter (high) [heat-side] CH1-CH64 2DAC-2DEB Integral time limiter (low) [heat-side] CH1-CH64 2DEC-2E2B Derivative time limiter (high) [heat-side] CH1-CH64 2E2C-2E6B Derivative time limiter (low) [heat-side] CH1-CH64 2E6C-2EAB Proportional band limiter (high) [cool-side] CH1-CH64 2EAC-2EEB Proportional band limiter (low) [cool-side] CH1-CH64 2EEC-2F2B Integral time limiter (high) [cool-side] CH1-CH64 2F2C-2F6B Integral time limiter (low) [cool-side] CH1-CH64 2F6C-2FAB Derivative time limiter (high) [cool-side] CH1-CH64 2FAC-2FEB Derivative time limiter (low) [cool-side] CH1-CH64 2FEC-302B Open/Close output neutral zone CH1-CH64 302C-306B Action at feedback resistance (FBR) input error CH1-CH64 306C-30AB Feedback adjustment CH1-CH64 30AC-30EB Control motor time CH1-CH64 30EC-312B Integrated output limiter CH1-CH64 312C-316B Valve action at STOP CH1-CH64 316C-31AB ST proportional band adjusting factor CH1-CH64 31AC-31EB ST integral time adjusting factor CH1-CH64 31EC-322B ST derivative time adjusting factor CH1-CH64 322C-326B ST start condition CH1-CH64 326C-32AB Automatic temperature rise group CH1-CH64 32AC-32EB Automatic temperature rise dead time CH1-CH64 32EC-332B Automatic temperature rise gradient data CH1-CH64 332C-336B EDS transfer time decimal point position CH1-CH64 336C-33AB Output average processing time for EDS CH1-CH64 33AC-33EB Responsive action trigger point for EDS CH1-CH64 33EC-342B Setting change rate limiter unit time CH1-CH64 342C-346B Soak time unit CH1-CH64 346C-34AB Setting limiter (high) CH1-CH64 34AC-34EB Setting limiter (low) CH1-CH64 34EC-352B PV transfer function CH1-CH64 352C-356B Operation mode assignment 1 (Logic output selection function) Logic output 1 to 4 CH1-CH64 356C-35AB Operation mode assignment 2 (Logic output selection function) Logic output 5 to 8 CH1-CH64 35AC-35EB SV select function CH1-CH64 35EC-362B Remote SV function master channel module address CH1-CH64 362C-366B Remote SV function master channel selection CH1-CH64 366C-36AB Output distribution master channel module address CH1-CH64 36AC-36EB Output distribution master channel selection CH1-CH64 36EC-372B Address of interacting modules CH1-CH64 372C-376B Channel selection of interacting modules CH1-CH64 376C-37AB Selection switch of interacting modules CH1-CH64 376C.0-37AB.0 Memory area number (Selection switch of interacting modules) CH1-CH64 376C.1-37AB.1 Operation mode (Selection switch of interacting modules) CH1-CH64 376C.2-37AB.2 Auto/Manual (Selection switch of interacting modules) CH1-CH64 376C.3-37AB.3 Remote/Local (Selection switch of interacting modules) CH1-CH64 376C.4-37AB.4 EDS start signal (Selection switch of interacting modules) CH1-CH64 376C.5-37AB.5 Interlock release (Selection switch of interacting modules) CH1-CH64 376C.6-37AB.6 Suspension of area soak time (Selection switch of interacting modules) CH1-CH64 37AC-37BB TIO Interval time CH1-CH16 386C-38AB Setting memory area number CH1-CH64 38AC-38EB Event 1 set value (EV1) CH1-CH64 38EC-392B Event 2 set value (EV2) CH1-CH64 392C-396B Event 3 set value (EV3) CH1-CH64 396C-39AB Event 4 set value (EV4) CH1-CH64 39AC-39EB Control loop break alarm (LBA) time CH1-CH64 39EC-3A2B LBA deadband CH1-CH64 3A2C-3A6B Set value (SV) CH1-CH64 3A6C-3AAB Proportional band [heat-side] CH1-CH64 3AAC-3AEB Integral time [heat-side] CH1-CH64 3AEC-3B2B Derivative time [heat-side] CH1-CH64 3B2C-3B6B Control response parameter CH1-CH64 3B6C-3BAB Proportional band [cool-side] CH1-CH64 3BAC-3BEB Integral time [cool-side] CH1-CH64 3BEC-3C2B Derivative time [cool-side] CH1-CH64 3C2C-3C6B Overlap/Deadband CH1-CH64 3C6C-3CAB Manual reset CH1-CH64 3CAC-3CEB Setting change rate limiter (up) CH1-CH64 3CEC-3D2B Setting change rate limiter (down) CH1-CH64 3D2C-3D6B Area soak time CH1-CH64 3D6C-3DAB Link area number CH1-CH64 3E6C-3E7B Digital input (DI) state 1 CH1-CH16 3E6C.0-3E7B.0 DI1 (Digital input (DI) state 1) CH1-CH16 3E6C.1-3E7B.1 DI2 (Digital input (DI) state 1) CH1-CH16 3E6C.2-3E7B.2 DI3 (Digital input (DI) state 1) CH1-CH16 3E6C.3-3E7B.3 DI4 (Digital input (DI) state 1) CH1-CH16 3E6C.4-3E7B.4 DI5 (Digital input (DI) state 1) CH1-CH16 3E6C.5-3E7B.5 DI6 (Digital input (DI) state 1) CH1-CH16 3E6C.6-3E7B.6 DI7 (Digital input (DI) state 1) CH1-CH16 3E6C.7-3E7B.7 DI8 (Digital input (DI) state 1) CH1-CH16 3E7C-3E8B Digital output (DO) state 1 CH1-CH16 3E7C.0-3E8B.0 DO1 (Digital output (DO) state 1) CH1-CH16 3E7C.1-3E8B.1 DO2 (Digital output (DO) state 1) CH1-CH16 3E7C.2-3E8B.2 DO3 (Digital output (DO) state 1) CH1-CH16 3E7C.3-3E8B.3 DO4 (Digital output (DO) state 1) CH1-CH16 3E7C.4-3E8B.4 DO5 (Digital output (DO) state 1) CH1-CH16 3E7C.5-3E8B.5 DO6 (Digital output (DO) state 1) CH1-CH16 3E7C.6-3E8B.6 DO7 (Digital output (DO) state 1) CH1-CH16 3E7C.7-3E8B.7 DO8 (Digital output (DO) state 1) CH1-CH16 3FDC-3FEB DO manual output 1 CH1-CH16 3FDC.0-3FEB.0 DO1 manual output (DO manual output 1) CH1-CH16 3FDC.1-3FEB.1 DO2 manual output (DO manual output 1) CH1-CH16 3FDC.2-3FEB.2 DO3 manual output (DO manual output 1) CH1-CH16 3FDC.3-3FEB.3 DO4 manual output (DO manual output 1) CH1-CH16 3FDC.4-3FEB.4 DO5 manual output (DO manual output 1) CH1-CH16 3FDC.5-3FEB.5 DO6 manual output (DO manual output 1) CH1-CH16 3FDC.6-3FEB.6 DO7 manual output (DO manual output 1) CH1-CH16 3FDC.7-3FEB.7 DO8 manual output (DO manual output 1) CH1-CH16 3FEC-406B DO output distribution selection CH1-CH128 406C-40EB DO output distribution bias CH1-CH128 40EC-416B DO output distribution ratio CH1-CH128 416C-41EB DO proportional cycle time CH1-CH128 41EC-426B DO minimum ON/OFF time of proportioning cycle CH1-CH128 433C-434B DI function assignment CH1-CH16 434C-435B Memory area setting signal CH1-CH16 435C-436B DO signal assignment module address 1 CH1-CH16 436C-437B DO signal assignment module address 2 CH1-CH16 437C-438B DO output assignment 1 [DO1 to DO4] CH1-CH16 438C-439B DO output assignment 2 [DO5 to DO8] CH1-CH16 439C-441B DO energized/de-energized CH1-CH128 441C-449B DO output distribution master channel module address CH1-CH128 449C-451B DO output distribution master channel selection CH1-CH128 451C-459B DO manipulated output value (MV) at STOP mode CH1-CH128 459C-461B DO output limiter (high) CH1-CH128 461C-469B DO output limiter (low) CH1-CH128 469C-46AB Z-DIO Interval time CH1-CH16 46BC-477B Current transformer (CT) input value monitor CH1-CH192 477C-483B Load factor conversion CT monitor CH1-CH192 483C-48FB Heater break alarm (HBA) state monitor CH1-CH192 48FC-49BB Heater overcurrent alarm state monitor CH1-CH192 49BC-49CB Automatic setting state monitor CH1-CH16 4FCC-508B Heater break/Heater overcurrent alarm automatic setting selection CH1-CH192 508C-514B Automatic setting transfer CH1-CH192 514C-520B Heater break alarm (HBA) set value CH1-CH192 520C-52CB Heater break alarm (HBA) selection CH1-CH192 52CC-538B Heater overcurrent alarm set value CH1-CH192 538C-544B Heater overcurrent alarm selection CH1-CH192 544C-550B Heater break alarm (HBA) interlock release CH1-CH192 550C-55CB Heater overcurrent alarm interlock release CH1-CH192 5E0C-5E1B Set lock CH1-CH16 5E1C-5EDB CT type CH1-CH192 5EDC-5F9B CT ratio (CT number of winds) CH1-CH192 5F9C-605B Number of heater break alarm (HBA) delay times CH1-CH192 605C-611B Automatic setting factor for heater break alarm (HBA) CH1-CH192 611C-61DB Automatic setting factor for heater overcurrent alarm CH1-CH192 61DC-629B Determination current value for automatic setting CH1-CH192 629C-635B Automatic setting time CH1-CH192 635C-641B Module address assignments for CT input CH1-CH192 641C-64DB Module channel assignments for CT input CH1-CH192 64DC-659B Load factor conversion method 2 CH1-CH192 659C-65AB CT Interval time CH1-CH16 8000 Communication 1 protocol 8001 Communication 1 communication speed 8002 Communication 1 data bit configuration 8003 Communication 1 interval time 8004 Communication 2 protocol 8005 Communication 2 communication speed 8006 Communication 2 data bit configuration 8007 Communication 2 interval time 8008 Station number 8009 PC number (CPU No.) 800A Register type 800B Register start number (High-order 4-bit) 800C Register start number (Low-order 16 bit) 800D System data address bias 800E COM module link recognition time 800F PLC scanning time 8010 PLC communication start time 8011 Method for setting the number of connected modules 8012 Slave mapping method 8013 Number of connected modules (Z-TIO module) 8014 Number of connected modules (Z-DIO module) 8015 Number of connected modules (Z-CT module) 801A Number of valid groups 801B Control RUN/STOP holding setting (Each unit) [SigDataEnd]