Name=PLC1 REX-F MaxSigCnt=86 DataFormat=Hex [SigData] 00 M1 Measured-value (PV) input 01 AA First alarm output 02 AB Second alarm output 03 AC Heater break alarm output 04 O1 Manipulated output (Heating-side) 05 O2 Manipulated output (Cooling-side) 06 B1 Burnout 07 B2 Feedback resistance (FBR) input burnout 08 S2 Remote setting value (RS) 09 M2 Feedback resistance input value (POS) 0A M3 Current transformer input value 0B MS Set-value (SV) monitoring 0C J1 Auto/manual transfer 0D C1 Local/remote transfer 0E E1 Local/external memory area transfer 0F ZA Control area No. transfer 10 G1 PID control/auto-tuning transfer 11 RA Local mode/computer mode identification 12 SR Operation execution (RUN)/STOP transfer 13 ON Manipulated output value (MV) 14 S1 Set-value (SV) 15 A1 First alarm setting 16 A2 Second alarm setting 17 P1 Proportional band (Heating-side) 18 I1 Integral time 19 D1 Derivative time 1A CA Control response designation parameter 1B P2 Cooling-side proportional band 1C V1 Deadband 1D HH Setting change rate limit 1E PB PV bias 1F F1 PV digital filter 20 DP PV low input cut-off 21 RR RS ratio 22 RB RS bias 23 F2 RS digital filter 24 OH Output limit (High limit) 25 OL Output limit (Low limit) 26 OQ Cooling output Min. ON time 27 PH Increase in output change rate limit 28 PL Decrease in output change rate limit 29 IV Upper ON/OFF action (A) differential gap 2A IW Lower ON/OFF action (A) differential gap 2B OE Manual output at abnormality 2C GB AT bias 2D HA First alarm differential gap 2E TD First alarm timer setting 2F A3 Heater break alarm 30 HB Second alarm differential gap 31 TG Second alarm timer setting 32 LA Analog output (AO) Specification selection 33 HV Analog output (AO) Scale high limit 34 HW Analog output (AO) Scale low limit 35 V2 Neutral zone 36 VH Open/close output differential gap 37 SY Action selection at feedback resistance (FBR) input break 38 DA Bar-graph display selection 39 XI PV input type selection 3A AV Input abnormality determination point (High limit) 3B AW Input abnormality determination point (Low limit) 3C WH Action selection at input abnormality (High limit) 3D WL Action selection at input abnormality (Low limit) 3E XV Input programmable range (High limit) 3F XW Input programmable range (Low limit) 40 XU Decimal-point position selection 41 XH Square root extraction selection 42 SH Setting limit (High limit) 43 SL Setting limit (Low limit) 44 XR RS input type selection 45 XL SV tracking selection 46 T0 Proportioning cycle (Heating-side) 47 T1 Cooling-side proportioning cycle 48 XE Direct/reverse action selection 49 XN Hot/cold start selection 4A SX Start determination point 4B XA First alarm Action selection 4C NA First alarm Energized/de-energized selection 4D OA First alarm Action selection at input abnormality 4E WA First alarm Hold action selection 4F XB Second alarm Action selection 50 NB Second alarm Energized/de-energized selection 51 OB Second alarm Action selection at input abnormality 52 WB Second alarm Hold action selection 53 LK Set data lock level 54 LL Area lock 55 DH Operation RUN/STOP display lock [SigDataEnd]