Name=PLC1 REX-G9 MaxSigCnt=95 DataFormat=Hex [SigData] 00 M1 Measured-value (PV) input 01 AA First alarm output 02 AB Second alarm output 03 AC Third alarm output 04 O1 Manipulated output1 05 B1 Burnout 06 B2 Feedback resistance (FBR) input burnout 07 S2 Remote setting value 08 M2 Feedback display 09 MS Set-value (SV) monitoring 0A J1 Auto/Manual transfer 0B C1 Remote/Local transfer 0C E1 Local/external memory area transfer 0D ZA Control area No. transfer 0E G1 PID control/auto-tuning transfer 0F RA Computer mode/local mode identification 10 SR Operation execution (RUN)/STOP transfer 11 ON Manipulated output value 12 S1 Set-value (SV) 13 A1 First alarm setting 14 A2 Second alarm setting 15 A3 Third alarm setting 16 P1 Proportional band 17 I1 Integral time 18 D1 Derivative time 19 CA Control response designation parameter 1A PB PV bias 1B F1 PV digital filter 1C VA PV Moving average 1D DP PV low input cut-off 1E HH Setting change rate limiter (up) 1F HL Setting change rate limiter (down) 20 RR RS ratio 21 RB RS bias 22 F2 RS digital filter 23 VB RS Moving average 24 OH Output limit (High limit) 25 OL Output limit (Low limit) 26 PH Increase in output change rate limit 27 PL Decrease in output change rate limit 28 IV Upper ON/OFF action (A) differential gap 29 IW Lower ON/OFF action (A) differential gap 2A DG Derivative gain 2B OE Manual output at abnormality 2C GB AT bias 2D G2 AT cycles 2E HA Alarm 1 hysteresis 2F HB Alarm 2 hysteresis 30 HC Alarm 3 hysteresis 31 LA Analog output 1 Specification selection 32 HV Analog output 1 Scale high limit 33 HW Analog output 1 Scale low limit 34 LB Analog output 2 Specification selection 35 CV Analog output 2 Scale high limit 36 CW Analog output 2 Scale low limit 37 V2 Neutral zone 38 VH Open/close hysteresis 39 SY Action selection at feedback resistance (FBR) input break 3A TL Display update cycle 3B DA Deflection bar graph(display/non-display) 3C DB RS bar graph(display/non-display) 3D DC PV bar graph(display/non-display) 3E DE Range of display in deflection bar graph 3F XI PV input type selection 40 AV Input abnormality determination point (High limit) 41 AW Input abnormality determination point (Low limit) 42 WH Action selection at input abnormality (High limit) 43 WL Action selection at input abnormality (Low limit) 44 XV Input programmable range (High limit) 45 XW Input programmable range (Low limit) 46 PU PV input unit 47 XU Decimal-point position selection 48 XH Square root extraction selection 49 SH Setting limit (High limit) 4A SL Setting limit (Low limit) 4B XR RS input type selection 4C XL SV tracking selection 4D T0 Output cycles 4E XE Direct/reverse action selection 4F DT Derivative cycle 50 XN Hot/Cold start selection 51 XA First alarm Action selection 52 NA First alarm Energized/de-energized selection 53 OA First alarm Action selection at input abnormality 54 WA First alarm Hold action selection 55 XB Second alarm Action selection 56 NB Second alarm Energized/de-energized selection 57 OB Second alarm Action selection at input abnormality 58 WB Second alarm Hold action selection 59 XC Third alarm Action selection 5A NC Third alarm Energized/de-energized selection 5B OC Third alarm Action selection at input abnormality 5C WC Third alarm Hold action selection 5D JT Power supply frequency 5E LK Setting lock No. [SigDataEnd]