Name=PLC1 PC900 MaxSigCnt=1705 DataFormat=Hex [SigData] 0001 Fixed value control Main setting value setting 0002 Fixed value control Control output (OUT1) proportional band setting 0003 Fixed value control Integral time setting 0004 Fixed value control Derivative time setting 0005 Fixed value control Anti-reset windup setting 0006 Fixed value control Control output (OUT2) proportional band setting 0007 Fixed value control Alarm 1 (A1) action point setting 0008 Fixed value control Alarm 2 (A2) action point setting 0009 Fixed value control Alarm 3 (A3) action point setting 000A Fixed value control Alarm 4 (A4) action point setting 000B Automatic/Manual control changing mode 000C Manual manipulating value setting 000D PID auto-tuning action selection 000E PID auto-tuning Performance/Cancellation 000F Alarm 3 (A3) action form selection 0010 Alarm 4 (A4) action form selection 0011 Alarm 1 (A1) hysteresis setting 0012 Alarm 2 (A2) hysteresis setting 0013 Alarm 3 (A3) hysteresis setting 0014 Alarm 4 (A4) hysteresis setting 0015 Alarm 1 (A1) delayed timer setting 0016 Alarm 2 (A2) delayed timer setting 0017 Alarm 3 (A3) delayed timer setting 0018 Alarm 4 (A4) delayed timer setting 0019 Loop break alarm time setting 001A Loop break alarm span setting 001B Control output (OUT1) proportional cycle setting 001C Control output (OUT1) high limit setting 001D Control output (OUT1) low limit setting 001E Control output (OUT1) ON/OFF hysteresis setting 001F Control output (OUT1) changing rate limit setting 0020 Control output (OUT2) proportional cycle setting 0021 Control output (OUT2) action selection 0022 Control output (OUT2) high limit setting 0023 Control output (OUT2) low limit setting 0024 Control output (OUT2) ON/OFF hysteresis setting 0025 Overlap band/Dead band setting 0026 Open/Closed output dead band setting 0027 Main setting value (SV) high limit setting 0028 Main setting value (SV) low limit setting 0029 Transmission output mode selection 002A Transmission output high limit setting 002B Transmission output low limit setting 002C Scaling high limit setting 002D Scaling low limit setting 002E Decimal point place selection 002F Sensor correction setting 0030 PV filter time constant setting 0031 Setting value lock selection 0032 Step temperature setting value (SV) [when program control start] setting 0033 Program control starting system selection 0034 Status after power failure restored selection 0035 Step time unit selection 0036 Step time indicating method selection 0037 Step temperature indicating method selection 0038 Pattern end output time setting 0039 Step temperature setting value (SV) when program end holding function selection 003A Time signal 1 output/Status output (RUN) selection 003B Time signal 2 output/Status output (HOLD) selection 003C Time signal 3 output/Status output (WAIT) selection 003D Time signal 4 output/Status output (FAST) selection 003E Time signal 5 output/Status output (STOP) selection 003F Running pattern number setting 0040 Pattern number selection to be set 0041 Control mode change 0042 Program control Run/Stop 0043 Holds the Progress time during Program control 0044 Advances the step to the next during Program control 0045 Returns the step to the previous during Program control 0046 Open output time setting 0047 Close output time setting 0080 Current Process variable (PV) reading 0081 Current Control output (OUT1) Manipulating value (MV) reading 0082 Current Control output (OUT2) Manipulating value (MV) reading 0083 Current Setting value (SV) reading 0084 Current Performing step remaining time reading 0085 Current Performing pattern and step reading 0086 Current output status reading [from Control output(OUT1 OPEN) to Downscale] 0086.0 Control output (OUT1 OPEN) 0086.1 Control output (OUT2 CLOSED) 0086.2 Alarm 1 (Pattern end) output 0086.3 Alarm 2 (Pattern end) output 0086.4 Alarm 3 (Pattern end) output 0086.5 Alarm 4 (Pattern end) output 0086.6 Loop break alarm output 0086.7 Upscale 0086.8 Downscale 0087 Current output status reading [from Time signal 1 (RUN) to Time signal 8 output] 0087.0 Time signal 1 (RUN) output 0087.1 Time signal 2 (HOLD) output 0087.2 Time signal 3 (WAIT) output 0087.3 Time signal 4 (FAST) output 0087.4 Time signal 5 (STOP) output 0087.5 Time signal 6 output 0087.6 Time signal 7 output 0087.7 Time signal 8 output 0088 Current running status reading [from Control mode to Program control (Wait)] 0088.0 Control mode 0088.1 Automatic/Manual control 0088.2 Auto-tuning 0088.3 Program control 0088.4 Program control (Hold) 0088.5 Program control (Wait) 1000 Temperature setting value for Pattern 0 , Step 0 1001 Time setting value for Pattern 0 , Step 0 1002 PID block number selection to be used for Pattern 0 , Step 0 1003 Time signal 1 Block number selection to be used for Pattern 0 , Step 0 1004 Time signal 2 Block number selection for Pattern 0 , Step 0 1005 Time signal 3 Block number selection for Pattern 0 , Step 0 1006 Time signal 4 Block number selection for Pattern 0 , Step 0 1007 Time signal 5 Block number selection for Pattern 0 , Step 0 1008 Time signal 6 Block number selection for Pattern 0 , Step 0 1009 Time signal 7 Block number selection for Pattern 0 , Step 0 100A Time signal 8 Block number selection for Pattern 0 , Step 0 100B Wait block number selection to be used for Pattern 0 , Step 0 100C Alarm block number selection to be used for Pattern 0 , Step 0 100D Output block number selection to be used for Pattern 0 , Step 0 1010 Temperature setting value for Pattern 0 , Step 1 1011 Time setting value for Pattern 0 , Step 1 1012 PID block number selection to be used for Pattern 0 , Step 1 1013 Time signal 1 Block number selection to be used for Pattern 0 , Step 1 1014 Time signal 2 Block number selection for Pattern 0 , Step 1 1015 Time signal 3 Block number selection for Pattern 0 , Step 1 1016 Time signal 4 Block number selection for Pattern 0 , Step 1 1017 Time signal 5 Block number selection for Pattern 0 , Step 1 1018 Time signal 6 Block number selection for Pattern 0 , Step 1 1019 Time signal 7 Block number selection for Pattern 0 , Step 1 101A Time signal 8 Block number selection for Pattern 0 , Step 1 101B Wait block number selection to be used for Pattern 0 , Step 1 101C Alarm block number selection to be used for Pattern 0 , Step 1 101D Output block number selection to be used for Pattern 0 , Step 1 1020 Temperature setting value for Pattern 0 , Step 2 1021 Time setting value for Pattern 0 , Step 2 1022 PID block number selection to be used for Pattern 0 , Step 2 1023 Time signal 1 Block number selection to be used for Pattern 0 , Step 2 1024 Time signal 2 Block number selection for Pattern 0 , Step 2 1025 Time signal 3 Block number selection for Pattern 0 , Step 2 1026 Time signal 4 Block number selection for Pattern 0 , Step 2 1027 Time signal 5 Block number selection for Pattern 0 , Step 2 1028 Time signal 6 Block number selection for Pattern 0 , Step 2 1029 Time signal 7 Block number selection for Pattern 0 , Step 2 102A Time signal 8 Block number selection for Pattern 0 , Step 2 102B Wait block number selection to be used for Pattern 0 , Step 2 102C Alarm block number selection to be used for Pattern 0 , Step 2 102D Output block number selection to be used for Pattern 0 , Step 2 1030 Temperature setting value for Pattern 0 , Step 3 1031 Time setting value for Pattern 0 , Step 3 1032 PID block number selection to be used for Pattern 0 , Step 3 1033 Time signal 1 Block number selection to be used for Pattern 0 , Step 3 1034 Time signal 2 Block number selection for Pattern 0 , Step 3 1035 Time signal 3 Block number selection for Pattern 0 , Step 3 1036 Time signal 4 Block number selection for Pattern 0 , Step 3 1037 Time signal 5 Block number selection for Pattern 0 , Step 3 1038 Time signal 6 Block number selection for Pattern 0 , Step 3 1039 Time signal 7 Block number selection for Pattern 0 , Step 3 103A Time signal 8 Block number selection for Pattern 0 , Step 3 103B Wait block number selection to be used for Pattern 0 , Step 3 103C Alarm block number selection to be used for Pattern 0 , Step 3 103D Output block number selection to be used for Pattern 0 , Step 3 1040 Temperature setting value for Pattern 0 , Step 4 1041 Time setting value for Pattern 0 , Step 4 1042 PID block number selection to be used for Pattern 0 , Step 4 1043 Time signal 1 Block number selection to be used for Pattern 0 , Step 4 1044 Time signal 2 Block number selection for Pattern 0 , Step 4 1045 Time signal 3 Block number selection for Pattern 0 , Step 4 1046 Time signal 4 Block number selection for Pattern 0 , Step 4 1047 Time signal 5 Block number selection for Pattern 0 , Step 4 1048 Time signal 6 Block number selection for Pattern 0 , Step 4 1049 Time signal 7 Block number selection for Pattern 0 , Step 4 104A Time signal 8 Block number selection for Pattern 0 , Step 4 104B Wait block number selection to be used for Pattern 0 , Step 4 104C Alarm block number selection to be used for Pattern 0 , Step 4 104D Output block number selection to be used for Pattern 0 , Step 4 1050 Temperature setting value for Pattern 0 , Step 5 1051 Time setting value for Pattern 0 , Step 5 1052 PID block number selection to be used for Pattern 0 , Step 5 1053 Time signal 1 Block number selection to be used for Pattern 0 , Step 5 1054 Time signal 2 Block number selection for Pattern 0 , Step 5 1055 Time signal 3 Block number selection for Pattern 0 , Step 5 1056 Time signal 4 Block number selection for Pattern 0 , Step 5 1057 Time signal 5 Block number selection for Pattern 0 , Step 5 1058 Time signal 6 Block number selection for Pattern 0 , Step 5 1059 Time signal 7 Block number selection for Pattern 0 , Step 5 105A Time signal 8 Block number selection for Pattern 0 , Step 5 105B Wait block number selection to be used for Pattern 0 , Step 5 105C Alarm block number selection to be used for Pattern 0 , Step 5 105D Output block number selection to be used for Pattern 0 , Step 5 1060 Temperature setting value for Pattern 0 , Step 6 1061 Time setting value for Pattern 0 , Step 6 1062 PID block number selection to be used for Pattern 0 , Step 6 1063 Time signal 1 Block number selection to be used for Pattern 0 , Step 6 1064 Time signal 2 Block number selection for Pattern 0 , Step 6 1065 Time signal 3 Block number selection for Pattern 0 , Step 6 1066 Time signal 4 Block number selection for Pattern 0 , Step 6 1067 Time signal 5 Block number selection for Pattern 0 , Step 6 1068 Time signal 6 Block number selection for Pattern 0 , Step 6 1069 Time signal 7 Block number selection for Pattern 0 , Step 6 106A Time signal 8 Block number selection for Pattern 0 , Step 6 106B Wait block number selection to be used for Pattern 0 , Step 6 106C Alarm block number selection to be used for Pattern 0 , Step 6 106D Output block number selection to be used for Pattern 0 , Step 6 1070 Temperature setting value for Pattern 0 , Step 7 1071 Time setting value for Pattern 0 , Step 7 1072 PID block number selection to be used for Pattern 0 , Step 7 1073 Time signal 1 Block number selection to be used for Pattern 0 , Step 7 1074 Time signal 2 Block number selection for Pattern 0 , Step 7 1075 Time signal 3 Block number selection for Pattern 0 , Step 7 1076 Time signal 4 Block number selection for Pattern 0 , Step 7 1077 Time signal 5 Block number selection for Pattern 0 , Step 7 1078 Time signal 6 Block number selection for Pattern 0 , Step 7 1079 Time signal 7 Block number selection for Pattern 0 , Step 7 107A Time signal 8 Block number selection for Pattern 0 , Step 7 107B Wait block number selection to be used for Pattern 0 , Step 7 107C Alarm block number selection to be used for Pattern 0 , Step 7 107D Output block number selection to be used for Pattern 0 , Step 7 1080 Temperature setting value for Pattern 0 , Step 8 1081 Time setting value for Pattern 0 , Step 8 1082 PID block number selection to be used for Pattern 0 , Step 8 1083 Time signal 1 Block number selection to be used for Pattern 0 , Step 8 1084 Time signal 2 Block number selection for Pattern 0 , Step 8 1085 Time signal 3 Block number selection for Pattern 0 , Step 8 1086 Time signal 4 Block number selection for Pattern 0 , Step 8 1087 Time signal 5 Block number selection for Pattern 0 , Step 8 1088 Time signal 6 Block number selection for Pattern 0 , Step 8 1089 Time signal 7 Block number selection for Pattern 0 , Step 8 108A Time signal 8 Block number selection for Pattern 0 , Step 8 108B Wait block number selection to be used for Pattern 0 , Step 8 108C Alarm block number selection to be used for Pattern 0 , Step 8 108D Output block number selection to be used for Pattern 0 , Step 8 1090 Temperature setting value for Pattern 0 , Step 9 1091 Time setting value for Pattern 0 , Step 9 1092 PID block number selection to be used for Pattern 0 , Step 9 1093 Time signal 1 Block number selection to be used for Pattern 0 , Step 9 1094 Time signal 2 Block number selection for Pattern 0 , Step 9 1095 Time signal 3 Block number selection for Pattern 0 , Step 9 1096 Time signal 4 Block number selection for Pattern 0 , Step 9 1097 Time signal 5 Block number selection for Pattern 0 , Step 9 1098 Time signal 6 Block number selection for Pattern 0 , Step 9 1099 Time signal 7 Block number selection for Pattern 0 , Step 9 109A Time signal 8 Block number selection for Pattern 0 , Step 9 109B Wait block number selection to be used for Pattern 0 , Step 9 108C Alarm block number selection to be used for Pattern 0 , Step 9 108D Output block number selection to be used for Pattern 0 , Step 9 1100 Temperature setting value for Pattern 1 , Step 0 1101 Time setting value for Pattern 1 , Step 0 1102 PID block number selection to be used for Pattern 1 , Step 0 1103 Time signal 1 Block number selection to be used for Pattern 1 , Step 0 1104 Time signal 2 Block number selection for Pattern 1 , Step 0 1105 Time signal 3 Block number selection for Pattern 1 , Step 0 1106 Time signal 4 Block number selection for Pattern 1 , Step 0 1107 Time signal 5 Block number selection for Pattern 1 , Step 0 1108 Time signal 6 Block number selection for Pattern 1 , Step 0 1109 Time signal 7 Block number selection for Pattern 1 , Step 0 110A Time signal 8 Block number selection for Pattern 1 , Step 0 110B Wait block number selection to be used for Pattern 1 , Step 0 110C Alarm block number selection to be used for Pattern 1 , Step 0 110D Output block number selection to be used for Pattern 1 , Step 0 1110 Temperature setting value for Pattern 1 , Step 1 1111 Time setting value for Pattern 1 , Step 1 1112 PID block number selection to be for used Pattern 1 , Step 1 1113 Time signal 1 Block number selection to be used for Pattern 1 , Step 1 1114 Time signal 2 Block number selection for Pattern 1 , Step 1 1115 Time signal 3 Block number selection for Pattern 1 , Step 1 1116 Time signal 4 Block number selection for Pattern 1 , Step 1 1117 Time signal 5 Block number selection for Pattern 1 , Step 1 1118 Time signal 6 Block number selection for Pattern 1 , Step 1 1119 Time signal 7 Block number selection for Pattern 1 , Step 1 111A Time signal 8 Block number selection for Pattern 1 , Step 1 111B Wait block number selection to be used for Pattern 1 , Step 1 111C Alarm block number selection to be used for Pattern 1 , Step 1 111D Output block number selection to be used for Pattern 1 , Step 1 1120 Temperature setting value for Pattern 1 , Step 2 1121 Time setting value for Pattern 1 , Step 2 1122 PID block number selection to be used for Pattern 1 , Step 2 1123 Time signal 1 Block number selection to be used for Pattern 1 , Step 2 1124 Time signal 2 Block number selection for Pattern 1 , Step 2 1125 Time signal 3 Block number selection for Pattern 1 , Step 2 1126 Time signal 4 Block number selection for Pattern 1 , Step 2 1127 Time signal 5 Block number selection for Pattern 1 , Step 2 1128 Time signal 6 Block number selection for Pattern 1 , Step 2 1129 Time signal 7 Block number selection for Pattern 1 , Step 2 112A Time signal 8 Block number selection for Pattern 1 , Step 2 112B Wait block number selection to be used for Pattern 1 , Step 2 112C Alarm block number selection to be used for Pattern 1 , Step 2 112D Output block number selection to be used for Pattern 1 , Step 2 1130 Temperature setting value for Pattern 1 , Step 3 1131 Time setting value for Pattern 1 , Step 3 1132 PID block number selection to be used for Pattern 1 , Step 3 1133 Time signal 1 Block number selection to be used for Pattern 1 , Step 3 1134 Time signal 2 Block number selection for Pattern 1 , Step 3 1135 Time signal 3 Block number selection for Pattern 1 , Step 3 1136 Time signal 4 Block number selection for Pattern 1 , Step 3 1137 Time signal 5 Block number selection for Pattern 1 , Step 3 1138 Time signal 6 Block number selection for Pattern 1 , Step 3 1139 Time signal 7 Block number selection for Pattern 1 , Step 3 113A Time signal 8 Block number selection for Pattern 1 , Step 3 113B Wait block number selection to be used for Pattern 1 , Step 3 113C Alarm block number selection to be used for Pattern 1 , Step 3 113D Output block number selection to be used for Pattern 1 , Step 3 1140 Temperature setting value for Pattern 1 , Step 4 1141 Time setting value for Pattern 1 , Step 4 1142 PID block number selection to be used for Pattern 1 , Step 4 1143 Time signal 1 Block number selection to be used for Pattern 1 , Step 4 1144 Time signal 2 Block number selection for Pattern 1 , Step 4 1145 Time signal 3 Block number selection for Pattern 1 , Step 4 1146 Time signal 4 Block number selection for Pattern 1 , Step 4 1147 Time signal 5 Block number selection for Pattern 1 , Step 4 1148 Time signal 6 Block number selection for Pattern 1 , Step 4 1149 Time signal 7 Block number selection for Pattern 1 , Step 4 114A Time signal 8 Block number selection for Pattern 1 , Step 4 114B Wait block number selection to be used for Pattern 1 , Step 4 114C Alarm block number selection to be used for Pattern 1 , Step 4 114D Output block number selection to be used for Pattern 1 , Step 4 1150 Temperature setting value for Pattern 1 , Step 5 1151 Time setting value for Pattern 1 , Step 5 1152 PID block number selection to be used for Pattern 1 , Step 5 1153 Time signal 1 Block number selection to be used for Pattern 1 , Step 5 1154 Time signal 2 Block number selection for Pattern 1 , Step 5 1155 Time signal 3 Block number selection for Pattern 1 , Step 5 1156 Time signal 4 Block number selection for Pattern 1 , Step 5 1157 Time signal 5 Block number selection for Pattern 1 , Step 5 1158 Time signal 6 Block number selection for Pattern 1 , Step 5 1159 Time signal 7 Block number selection for Pattern 1 , Step 5 115A Time signal 8 Block number selection for Pattern 1 , Step 5 115B Wait block number selection to be used for Pattern 1 , Step 5 115C Alarm block number selection to be used for Pattern 1 , Step 5 115D Output block number selection to be used for Pattern 1 , Step 5 1160 Temperature setting value for Pattern 1 , Step 6 1161 Time setting value for Pattern 1 , Step 6 1162 PID block number selection to be used for Pattern 1 , Step 6 1163 Time signal 1 Block number selection to be used for Pattern 1 , Step 6 1164 Time signal 2 Block number selection for Pattern 1 , Step 6 1165 Time signal 3 Block number selection for Pattern 1 , Step 6 1166 Time signal 4 Block number selection for Pattern 1 , Step 6 1167 Time signal 5 Block number selection for Pattern 1 , Step 6 1168 Time signal 6 Block number selection for Pattern 1 , Step 6 1169 Time signal 7 Block number selection for Pattern 1 , Step 6 116A Time signal 8 Block number selection for Pattern 1 , Step 6 116B Wait block number selection to be used for Pattern 1 , Step 6 116C Alarm block number selection to be used for Pattern 1 , Step 6 116D Output block number selection to be used for Pattern 1 , Step 6 1170 Temperature setting value for Pattern 1 , Step 7 1171 Time setting value for Pattern 1 , Step 7 1172 PID block number selection to be used for Pattern 1 , Step 7 1173 Time signal 1 Block number selection to be used for Pattern 1 , Step 7 1174 Time signal 2 Block number selection for Pattern 1 , Step 7 1175 Time signal 3 Block number selection for Pattern 1 , Step 7 1176 Time signal 4 Block number selection for Pattern 1 , Step 7 1177 Time signal 5 Block number selection for Pattern 1 , Step 7 1178 Time signal 6 Block number selection for Pattern 1 , Step 7 1179 Time signal 7 Block number selection for Pattern 1 , Step 7 117A Time signal 8 Block number selection for Pattern 1 , Step 7 117B Wait block number selection to be used for Pattern 1 , Step 7 117C Alarm block number selection to be used for Pattern 1 , Step 7 117D Output block number selection to be used for Pattern 1 , Step 7 1180 Temperature setting value for Pattern 1 , Step 8 1181 Time setting value for Pattern 1 , Step 8 1182 PID block number selection to be used for Pattern 1 , Step 8 1183 Time signal 1 Block number selection to be used for Pattern 1 , Step 8 1184 Time signal 2 Block number selection for Pattern 1 , Step 8 1185 Time signal 3 Block number selection for Pattern 1 , Step 8 1186 Time signal 4 Block number selection for Pattern 1 , Step 8 1187 Time signal 5 Block number selection for Pattern 1 , Step 8 1188 Time signal 6 Block number selection for Pattern 1 , Step 8 1189 Time signal 7 Block number selection for Pattern 1 , Step 8 118A Time signal 8 Block number selection for Pattern 1 , Step 8 118B Wait block number selection to be used for Pattern 1 , Step 8 118C Alarm block number selection to be used for Pattern 1 , Step 8 118D Output block number selection to be used for Pattern 1 , Step 8 1190 Temperature setting value for Pattern 1 , Step 9 1191 Time setting value for Pattern 1 , Step 9 1192 PID block number selection to be used for Pattern 1 , Step 9 1193 Time signal 1 Block number selection to be used for Pattern 1 , Step 9 1194 Time signal 2 Block number selection for Pattern 1 , Step 9 1195 Time signal 3 Block number selection for Pattern 1 , Step 9 1196 Time signal 4 Block number selection for Pattern 1 , Step 9 1197 Time signal 5 Block number selection for Pattern 1 , Step 9 1198 Time signal 6 Block number selection for Pattern 1 , Step 9 1199 Time signal 7 Block number selection for Pattern 1 , Step 9 119A Time signal 8 Block number selection for Pattern 1 , Step 9 119B Wait block number selection to be used for Pattern 1 , Step 9 119C Alarm block number selection to be used for Pattern 1 , Step 9 119D Output block number selection to be used for Pattern 1 , Step 9 1200 Temperature setting value for Pattern 2 , Step 0 1201 Time setting value for Pattern 2 , Step 0 1202 PID block number selection to be used for Pattern 2 , Step 0 1203 Time signal 1 Block number selection to be used for Pattern 2 , Step 0 1204 Time signal 2 Block number selection for Pattern 2 , Step 0 1205 Time signal 3 Block number selection for Pattern 2 , Step 0 1206 Time signal 4 Block number selection for Pattern 2 , Step 0 1207 Time signal 5 Block number selection for Pattern 2 , Step 0 1208 Time signal 6 Block number selection for Pattern 2 , Step 0 1209 Time signal 7 Block number selection for Pattern 2 , Step 0 120A Time signal 8 Block number selection for Pattern 2 , Step 0 120B Wait block number selection to be used for Pattern 2 , Step 0 120C Alarm block number selection to be used for Pattern 2 , Step 0 120D Output block number selection to be used for Pattern 2 , Step 0 1210 Temperature setting value for Pattern 2 , Step 1 1211 Time setting value for Pattern 2 , Step 1 1212 PID block number selection to be used for Pattern 2 , Step 1 1213 Time signal 1 Block number selection to be used for Pattern 2 , Step 1 1214 Time signal 2 Block number selection for Pattern 2 , Step 1 1215 Time signal 3 Block number selection for Pattern 2 , Step 1 1216 Time signal 4 Block number selection for Pattern 2 , Step 1 1217 Time signal 5 Block number selection for Pattern 2 , Step 1 1218 Time signal 6 Block number selection for Pattern 2 , Step 1 1219 Time signal 7 Block number selection for Pattern 2 , Step 1 121A Time signal 8 Block number selection for Pattern 2 , Step 1 121B Wait block number selection to be used for Pattern 2 , Step 1 121C Alarm block number selection to be used for Pattern 2 , Step 1 121D Output block number selection to be used for Pattern 2 , Step 1 1220 Temperature setting value for Pattern 2 , Step 2 1221 Time setting value for Pattern 2 , Step 2 1222 PID block number selection to be used for Pattern 2 , Step 2 1223 Time signal 1 Block number selection to be used for Pattern 2 , Step 2 1224 Time signal 2 Block number selection for Pattern 2 , Step 2 1225 Time signal 3 Block number selection for Pattern 2 , Step 2 1226 Time signal 4 Block number selection for Pattern 2 , Step 2 1227 Time signal 5 Block number selection for Pattern 2 , Step 2 1228 Time signal 6 Block number selection for Pattern 2 , Step 2 1229 Time signal 7 Block number selection for Pattern 2 , Step 2 122A Time signal 8 Block number selection for Pattern 2 , Step 2 122B Wait block number selection to be used for Pattern 2 , Step 2 122C Alarm block number selection to be used for Pattern 2 , Step 2 122D Output block number selection to be used for Pattern 2 , Step 2 1230 Temperature setting value for Pattern 2 , Step 3 1231 Time setting value for Pattern 2 , Step 3 1232 PID block number selection to be used for Pattern 2 , Step 3 1233 Time signal 1 Block number selection to be used for Pattern 2 , Step 3 1234 Time signal 2 Block number selection for Pattern 2 , Step 3 1235 Time signal 3 Block number selection for Pattern 2 , Step 3 1236 Time signal 4 Block number selection for Pattern 2 , Step 3 1237 Time signal 5 Block number selection for Pattern 2 , Step 3 1238 Time signal 6 Block number selection for Pattern 2 , Step 3 1239 Time signal 7 Block number selection for Pattern 2 , Step 3 123A Time signal 8 Block number selection for Pattern 2 , Step 3 123B Wait block number selection to be used for Pattern 2 , Step 3 123C Alarm block number selection to be used for Pattern 2 , Step 3 123D Output block number selection to be used for Pattern 2 , Step 3 1240 Temperature setting value for Pattern 2 , Step 4 1241 Time setting value for Pattern 2 , Step 4 1242 PID block number selection to be used for Pattern 2 , Step 4 1243 Time signal 1 Block number selection to be used for Pattern 2 , Step 4 1244 Time signal 2 Block number selection for Pattern 2 , Step 4 1245 Time signal 3 Block number selection for Pattern 2 , Step 4 1246 Time signal 4 Block number selection for Pattern 2 , Step 4 1247 Time signal 5 Block number selection for Pattern 2 , Step 4 1248 Time signal 6 Block number selection for Pattern 2 , Step 4 1249 Time signal 7 Block number selection for Pattern 2 , Step 4 124A Time signal 8 Block number selection for Pattern 2 , Step 4 124B Wait block number selection to be used for Pattern 2 , Step 4 124C Alarm block number selection to be used for Pattern 2 , Step 4 124D Output block number selection to be used for Pattern 2 , Step 4 1250 Temperature setting value for Pattern 2 , Step 5 1251 Time setting value for Pattern 2 , Step 5 1252 PID block number selection to be used for Pattern 2 , Step 5 1253 Time signal 1 Block number selection to be used for Pattern 2 , Step 5 1254 Time signal 2 Block number selection for Pattern 2 , Step 5 1255 Time signal 3 Block number selection for Pattern 2 , Step 5 1256 Time signal 4 Block number selection for Pattern 2 , Step 5 1257 Time signal 5 Block number selection for Pattern 2 , Step 5 1258 Time signal 6 Block number selection for Pattern 2 , Step 5 1259 Time signal 7 Block number selection for Pattern 2 , Step 5 125A Time signal 8 Block number selection for Pattern 2 , Step 5 125B Wait block number selection to be used for Pattern 2 , Step 5 125C Alarm block number selection to be used for Pattern 2 , Step 5 125D Output block number selection to be used for Pattern 2 , Step 5 1260 Temperature setting value for Pattern 2 , Step 6 1261 Time setting value for Pattern 2 , Step 6 1262 PID block number selection to be used for Pattern 2 , Step 6 1263 Time signal 1 Block number selection to be used for Pattern 2 , Step 6 1264 Time signal 2 Block number selection for Pattern 2 , Step 6 1265 Time signal 3 Block number selection for Pattern 2 , Step 6 1266 Time signal 4 Block number selection for Pattern 2 , Step 6 1267 Time signal 5 Block number selection for Pattern 2 , Step 6 1268 Time signal 6 Block number selection for Pattern 2 , Step 6 1269 Time signal 7 Block number selection for Pattern 2 , Step 6 126A Time signal 8 Block number selection for Pattern 2 , Step 6 126B Wait block number selection to be used for Pattern 2 , Step 6 126C Alarm block number selection to be used for Pattern 2 , Step 6 126D Output block number selection to be used for Pattern 2 , Step 6 1270 Temperature setting value for Pattern 2 , Step 7 1271 Time setting value for Pattern 2 , Step 7 1272 PID block number selection to be used for Pattern 2 , Step 7 1273 Time signal 1 Block number selection to be used for Pattern 2 , Step 7 1274 Time signal 2 Block number selection for Pattern 2 , Step 7 1275 Time signal 3 Block number selection for Pattern 2 , Step 7 1276 Time signal 4 Block number selection for Pattern 2 , Step 7 1277 Time signal 5 Block number selection for Pattern 2 , Step 7 1278 Time signal 6 Block number selection for Pattern 2 , Step 7 1279 Time signal 7 Block number selection for Pattern 2 , Step 7 127A Time signal 8 Block number selection for Pattern 2 , Step 7 127B Wait block number selection to be used for Pattern 2 , Step 7 127C Alarm block number selection to be used for Pattern 2 , Step 7 127D Output block number selection to be used for Pattern 2 , Step 7 1280 Temperature setting value for Pattern 2 , Step 8 1281 Time setting value for Pattern 2 , Step 8 1282 PID block number selection to be used for Pattern 2 , Step 8 1283 Time signal 1 Block number selection to be used for Pattern 2 , Step 8 1284 Time signal 2 Block number selection for Pattern 2 , Step 8 1285 Time signal 3 Block number selection for Pattern 2 , Step 8 1286 Time signal 4 Block number selection for Pattern 2 , Step 8 1287 Time signal 5 Block number selection for Pattern 2 , Step 8 1288 Time signal 6 Block number selection for Pattern 2 , Step 8 1289 Time signal 7 Block number selection for Pattern 2 , Step 8 128A Time signal 8 Block number selection for Pattern 2 , Step 8 128B Wait block number selection to be used for Pattern 2 , Step 8 128C Alarm block number selection to be used for Pattern 2 , Step 8 128D Output block number selection to be used for Pattern 2 , Step 8 1290 Temperature setting value for Pattern 2 , Step 9 1291 Time setting value for Pattern 2 , Step 9 1292 PID block number selection to be used for Pattern 2 , Step 9 1293 Time signal 1 Block number selection to be used for Pattern 2 , Step 9 1294 Time signal 2 Block number selection for Pattern 2 , Step 9 1295 Time signal 3 Block number selection for Pattern 2 , Step 9 1296 Time signal 4 Block number selection for Pattern 2 , Step 9 1297 Time signal 5 Block number selection for Pattern 2 , Step 9 1298 Time signal 6 Block number selection for Pattern 2 , Step 9 1299 Time signal 7 Block number selection for Pattern 2 , Step 9 129A Time signal 8 Block number selection for Pattern 2 , Step 9 129B Wait block number selection to be used for Pattern 2 , Step 9 129C Alarm block number selection to be used for Pattern 2 , Step 9 129D Output block number selection to be used for Pattern 2 , Step 9 1300 Temperature setting value for Pattern 3 , Step 0 1301 Time setting value for Pattern 3 , Step 0 1302 PID block number selection to be used for Pattern 3 , Step 0 1303 Time signal 1 Block number selection to be used for Pattern 3 , Step 0 1304 Time signal 2 Block number selection for Pattern 3 , Step 0 1305 Time signal 3 Block number selection for Pattern 3 , Step 0 1306 Time signal 4 Block number selection for Pattern 3 , Step 0 1307 Time signal 5 Block number selection for Pattern 3 , Step 0 1308 Time signal 6 Block number selection for Pattern 3 , Step 0 1309 Time signal 7 Block number selection for Pattern 3 , Step 0 130A Time signal 8 Block number selection for Pattern 3 , Step 0 130B Wait block number selection to be used for Pattern 3 , Step 0 130C Alarm block number selection to be used for Pattern 3 , Step 0 130D Output block number selection to be used for Pattern 3 , Step 0 1310 Temperature setting value for Pattern 3 , Step 1 1311 Time setting value for Pattern 3 , Step 1 1312 PID block number selection to be used for Pattern 3 , Step 1 1313 Time signal 1 Block number selection to be used for Pattern 3 , Step 1 1314 Time signal 2 Block number selection for Pattern 3 , Step 1 1315 Time signal 3 Block number selection for Pattern 3 , Step 1 1316 Time signal 4 Block number selection for Pattern 3 , Step 1 1317 Time signal 5 Block number selection for Pattern 3 , Step 1 1318 Time signal 6 Block number selection for Pattern 3 , Step 1 1319 Time signal 7 Block number selection for Pattern 3 , Step 1 131A Time signal 8 Block number selection for Pattern 3 , Step 1 131B Wait block number selection to be used for Pattern 3 , Step 1 131C Alarm block number selection to be used for Pattern 3 , Step 1 131D Output block number selection to be used for Pattern 3 , Step 1 1320 Temperature setting value for Pattern 3 , Step 2 1321 Time setting value for Pattern 3 , Step 2 1322 PID block number selection to be used for Pattern 3 , Step 2 1323 Time signal 1 Block number selection to be used for Pattern 3 , Step 2 1324 Time signal 2 Block number selection for Pattern 3 , Step 2 1325 Time signal 3 Block number selection for Pattern 3 , Step 2 1326 Time signal 4 Block number selection for Pattern 3 , Step 2 1327 Time signal 5 Block number selection for Pattern 3 , Step 2 1328 Time signal 6 Block number selection for Pattern 3 , Step 2 1329 Time signal 7 Block number selection for Pattern 3 , Step 2 132A Time signal 8 Block number selection for Pattern 3 , Step 2 132B Wait block number selection to be used for Pattern 3 , Step 2 132C Alarm block number selection to be used for Pattern 3 , Step 2 132D Output block number selection to be used for Pattern 3 , Step 2 1330 Temperature setting value for Pattern 3 , Step 3 1331 Time setting value for Pattern 3 , Step 3 1332 PID block number selection to be used for Pattern 3 , Step 3 1333 Time signal 1 Block number selection to be used for Pattern 3 , Step 3 1334 Time signal 2 Block number selection for Pattern 3 , Step 3 1335 Time signal 3 Block number selection for Pattern 3 , Step 3 1336 Time signal 4 Block number selection for Pattern 3 , Step 3 1337 Time signal 5 Block number selection for Pattern 3 , Step 3 1338 Time signal 6 Block number selection for Pattern 3 , Step 3 1339 Time signal 7 Block number selection for Pattern 3 , Step 3 133A Time signal 8 Block number selection for Pattern 3 , Step 3 133B Wait block number selection to be used for Pattern 3 , Step 3 133C Alarm block number selection to be used for Pattern 3 , Step 3 133D Output block number selection to be used for Pattern 3 , Step 3 1340 Temperature setting value for Pattern 3 , Step 4 1341 Time setting value for Pattern 3 , Step 4 1342 PID block number selection to be used for Pattern 3 , Step 4 1343 Time signal 1 Block number selection to be used for Pattern 3 , Step 4 1344 Time signal 2 Block number selection for Pattern 3 , Step 4 1345 Time signal 3 Block number selection for Pattern 3 , Step 4 1346 Time signal 4 Block number selection for Pattern 3 , Step 4 1347 Time signal 5 Block number selection for Pattern 3 , Step 4 1348 Time signal 6 Block number selection for Pattern 3 , Step 4 1349 Time signal 7 Block number selection for Pattern 3 , Step 4 134A Time signal 8 Block number selection for Pattern 3 , Step 4 134B Wait block number selection to be used for Pattern 3 , Step 4 134C Alarm block number selection to be used for Pattern 3 , Step 4 134D Output block number selection to be used for Pattern 3 , Step 4 1350 Temperature setting value for Pattern 3 , Step 5 1351 Time setting value for Pattern 3 , Step 5 1352 PID block number selection to be used for Pattern 3 , Step 5 1353 Time signal 1 Block number selection to be used for Pattern 3 , Step 5 1354 Time signal 2 Block number selection for Pattern 3 , Step 5 1355 Time signal 3 Block number selection for Pattern 3 , Step 5 1356 Time signal 4 Block number selection for Pattern 3 , Step 5 1357 Time signal 5 Block number selection for Pattern 3 , Step 5 1358 Time signal 6 Block number selection for Pattern 3 , Step 5 1359 Time signal 7 Block number selection for Pattern 3 , Step 5 135A Time signal 8 Block number selection for Pattern 3 , Step 5 135B Wait block number selection to be used for Pattern 3 , Step 5 135C Alarm block number selection to be used for Pattern 3 , Step 5 135D Output block number selection to be used for Pattern 3 , Step 5 1360 Temperature setting value for Pattern 3 , Step 6 1361 Time setting value for Pattern 3 , Step 6 1362 PID block number selection to be used for Pattern 3 , Step 6 1363 Time signal 1 Block number selection to be used for Pattern 3 , Step 6 1364 Time signal 2 Block number selection for Pattern 3 , Step 6 1365 Time signal 3 Block number selection for Pattern 3 , Step 6 1366 Time signal 4 Block number selection for Pattern 3 , Step 6 1367 Time signal 5 Block number selection for Pattern 3 , Step 6 1368 Time signal 6 Block number selection for Pattern 3 , Step 6 1369 Time signal 7 Block number selection for Pattern 3 , Step 6 136A Time signal 8 Block number selection for Pattern 3 , Step 6 136B Wait block number selection to be used for Pattern 3 , Step 6 136C Alarm block number selection to be used for Pattern 3 , Step 6 136D Output block number selection to be used for Pattern 3 , Step 6 1370 Temperature setting value for Pattern 3 , Step 7 1371 Time setting value for Pattern 3 , Step 7 1372 PID block number selection to be used for Pattern 3 , Step 7 1373 Time signal 1 Block number selection to be used for Pattern 3 , Step 7 1374 Time signal 2 Block number selection for Pattern 3 , Step 7 1375 Time signal 3 Block number selection for Pattern 3 , Step 7 1376 Time signal 4 Block number selection for Pattern 3 , Step 7 1377 Time signal 5 Block number selection for Pattern 3 , Step 7 1378 Time signal 6 Block number selection for Pattern 3 , Step 7 1379 Time signal 7 Block number selection for Pattern 3 , Step 7 137A Time signal 8 Block number selection for Pattern 3 , Step 7 137B Wait block number selection to be used for Pattern 3 , Step 7 137C Alarm block number selection to be used for Pattern 3 , Step 7 137D Output block number selection to be used for Pattern 3 , Step 7 1380 Temperature setting value for Pattern 3 , Step 8 1381 Time setting value for Pattern 3 , Step 8 1382 PID block number selection to be used for Pattern 3 , Step 8 1383 Time signal 1 Block number selection to be used for Pattern 3 , Step 8 1384 Time signal 2 Block number selection for Pattern 3 , Step 8 1385 Time signal 3 Block number selection for Pattern 3 , Step 8 1386 Time signal 4 Block number selection for Pattern 3 , Step 8 1387 Time signal 5 Block number selection for Pattern 3 , Step 8 1388 Time signal 6 Block number selection for Pattern 3 , Step 8 1389 Time signal 7 Block number selection for Pattern 3 , Step 8 138A Time signal 8 Block number selection for Pattern 3 , Step 8 138B Wait block number selection to be used for Pattern 3 , Step 8 138C Alarm block number selection to be used for Pattern 3 , Step 8 138D Output block number selection to be used for Pattern 3 , Step 8 1390 Temperature setting value for Pattern 3 , Step 9 1391 Time setting value for Pattern 3 , Step 9 1392 PID block number selection to be used for Pattern 3 , Step 9 1393 Time signal 1 Block number selection to be used for Pattern 3 , Step 9 1394 Time signal 2 Block number selection for Pattern 3 , Step 9 1395 Time signal 3 Block number selection for Pattern 3 , Step 9 1396 Time signal 4 Block number selection for Pattern 3 , Step 9 1397 Time signal 5 Block number selection for Pattern 3 , Step 9 1398 Time signal 6 Block number selection for Pattern 3 , Step 9 1399 Time signal 7 Block number selection for Pattern 3 , Step 9 139A Time signal 8 Block number selection for Pattern 3 , Step 9 139B Wait block number selection to be used for Pattern 3 , Step 9 139C Alarm block number selection to be used for Pattern 3 , Step 9 139D Output block number selection to be used for Pattern 3 , Step 9 1400 Temperature setting value for Pattern 4 , Step 0 1401 Time setting value for Pattern 4 , Step 0 1402 PID block number selection to be used for Pattern 4 , Step 0 1403 Time signal 1 Block number selection to be used for Pattern 4 , Step 0 1404 Time signal 2 Block number selection for Pattern 4 , Step 0 1405 Time signal 3 Block number selection for Pattern 4 , Step 0 1406 Time signal 4 Block number selection for Pattern 4 , Step 0 1407 Time signal 5 Block number selection for Pattern 4 , Step 0 1408 Time signal 6 Block number selection for Pattern 4 , Step 0 1409 Time signal 7 Block number selection for Pattern 4 , Step 0 140A Time signal 8 Block number selection for Pattern 4 , Step 0 140B Wait block number selection to be used for Pattern 4 , Step 0 140C Alarm block number selection to be used for Pattern 4 , Step 0 140D Output block number selection to be used for Pattern 4 , Step 0 1410 Temperature setting value for Pattern 4 , Step 1 1411 Time setting value for Pattern 4 , Step 1 1412 PID block number selection to be used for Pattern 4 , Step 1 1413 Time signal 1 Block number selection to be used for Pattern 4 , Step 1 1414 Time signal 2 Block number selection for Pattern 4 , Step 1 1415 Time signal 3 Block number selection for Pattern 4 , Step 1 1416 Time signal 4 Block number selection for Pattern 4 , Step 1 1417 Time signal 5 Block number selection for Pattern 4 , Step 1 1418 Time signal 6 Block number selection for Pattern 4 , Step 1 1419 Time signal 7 Block number selection for Pattern 4 , Step 1 141A Time signal 8 Block number selection for Pattern 4 , Step 1 141B Wait block number selection to be used for Pattern 4 , Step 1 141C Alarm block number selection to be used for Pattern 4 , Step 1 141D Output block number selection to be used for Pattern 4 , Step 1 1420 Temperature setting value for Pattern 4 , Step 2 1421 Time setting value for Pattern 4 , Step 2 1422 PID block number selection to be used for Pattern 4 , Step 2 1423 Time signal 1 Block number selection to be used for Pattern 4 , Step 2 1424 Time signal 2 Block number selection for Pattern 4 , Step 2 1425 Time signal 3 Block number selection for Pattern 4 , Step 2 1426 Time signal 4 Block number selection for Pattern 4 , Step 2 1427 Time signal 5 Block number selection for Pattern 4 , Step 2 1428 Time signal 6 Block number selection for Pattern 4 , Step 2 1429 Time signal 7 Block number selection for Pattern 4 , Step 2 142A Time signal 8 Block number selection for Pattern 4 , Step 2 142B Wait block number selection to be used for Pattern 4 , Step 2 142C Alarm block number selection to be used for Pattern 4 , Step 2 142D Output block number selection to be used for Pattern 4 , Step 2 1430 Temperature setting value for Pattern 4 , Step 3 1431 Time setting value for Pattern 4 , Step 3 1432 PID block number selection to be used for Pattern 4 , Step 3 1433 Time signal 1 Block number selection to be used for Pattern 4 , Step 3 1434 Time signal 2 Block number selection for Pattern 4 , Step 3 1435 Time signal 3 Block number selection for Pattern 4 , Step 3 1436 Time signal 4 Block number selection for Pattern 4 , Step 3 1437 Time signal 5 Block number selection for Pattern 4 , Step 3 1438 Time signal 6 Block number selection for Pattern 4 , Step 3 1439 Time signal 7 Block number selection for Pattern 4 , Step 3 143A Time signal 8 Block number selection for Pattern 4 , Step 3 143B Wait block number selection to be used for Pattern 4 , Step 3 143C Alarm block number selection to be used for Pattern 4 , Step 3 143D Output block number selection to be used for Pattern 4 , Step 3 1440 Temperature setting value for Pattern 4 , Step 4 1441 Time setting value for Pattern 4 , Step 4 1442 PID block number selection to be used for Pattern 4 , Step 4 1443 Time signal 1 Block number selection to be used for Pattern 4 , Step 4 1444 Time signal 2 Block number selection for Pattern 4 , Step 4 1445 Time signal 3 Block number selection for Pattern 4 , Step 4 1446 Time signal 4 Block number selection for Pattern 4 , Step 4 1447 Time signal 5 Block number selection for Pattern 4 , Step 4 1448 Time signal 6 Block number selection for Pattern 4 , Step 4 1449 Time signal 7 Block number selection for Pattern 4 , Step 4 144A Time signal 8 Block number selection for Pattern 4 , Step 4 144B Wait block number selection to be used for Pattern 4 , Step 4 144C Alarm block number selection to be used for Pattern 4 , Step 4 144D Output block number selection to be used for Pattern 4 , Step 4 1450 Temperature setting value for Pattern 4 , Step 5 1451 Time setting value for Pattern 4 , Step 5 1452 PID block number selection to be used for Pattern 4 , Step 5 1453 Time signal 1 Block number selection to be used for Pattern 4 , Step 5 1454 Time signal 2 Block number selection for Pattern 4 , Step 5 1455 Time signal 3 Block number selection for Pattern 4 , Step 5 1456 Time signal 4 Block number selection for Pattern 4 , Step 5 1457 Time signal 5 Block number selection for Pattern 4 , Step 5 1458 Time signal 6 Block number selection for Pattern 4 , Step 5 1459 Time signal 7 Block number selection for Pattern 4 , Step 5 145A Time signal 8 Block number selection for Pattern 4 , Step 5 145B Wait block number selection to be used for Pattern 4 , Step 5 145C Alarm block number selection to be used for Pattern 4 , Step 5 145D Output block number selection to be used for Pattern 4 , Step 5 1460 Temperature setting value for Pattern 4 , Step 6 1461 Time setting value for Pattern 4 , Step 6 1462 PID block number selection to be used for Pattern 4 , Step 6 1463 Time signal 1 Block number selection to be used for Pattern 4 , Step 6 1464 Time signal 2 Block number selection for Pattern 4 , Step 6 1465 Time signal 3 Block number selection for Pattern 4 , Step 6 1466 Time signal 4 Block number selection for Pattern 4 , Step 6 1467 Time signal 5 Block number selection for Pattern 4 , Step 6 1468 Time signal 6 Block number selection for Pattern 4 , Step 6 1469 Time signal 7 Block number selection for Pattern 4 , Step 6 146A Time signal 8 Block number selection for Pattern 4 , Step 6 146B Wait block number selection to be used for Pattern 4 , Step 6 146C Alarm block number selection to be used for Pattern 4 , Step 6 146D Output block number selection to be used for Pattern 4 , Step 6 1470 Temperature setting value for Pattern 4 , Step 7 1471 Time setting value for Pattern 4 , Step 7 1472 PID block number selection to be used for Pattern 4 , Step 7 1473 Time signal 1 Block number selection to be used for Pattern 4 , Step 7 1474 Time signal 2 Block number selection for Pattern 4 , Step 7 1475 Time signal 3 Block number selection for Pattern 4 , Step 7 1476 Time signal 4 Block number selection for Pattern 4 , Step 7 1477 Time signal 5 Block number selection for Pattern 4 , Step 7 1478 Time signal 6 Block number selection for Pattern 4 , Step 7 1479 Time signal 7 Block number selection for Pattern 4 , Step 7 147A Time signal 8 Block number selection for Pattern 4 , Step 7 147B Wait block number selection to be used for Pattern 4 , Step 7 147C Alarm block number selection to be used for Pattern 4 , Step 7 147D Output block number selection to be used for Pattern 4 , Step 7 1480 Temperature setting value for Pattern 4 , Step 8 1481 Time setting value for Pattern 4 , Step 8 1482 PID block number selection to be used for Pattern 4 , Step 8 1483 Time signal 1 Block number selection to be used for Pattern 4 , Step 8 1484 Time signal 2 Block number selection for Pattern 4 , Step 8 1485 Time signal 3 Block number selection for Pattern 4 , Step 8 1486 Time signal 4 Block number selection for Pattern 4 , Step 8 1487 Time signal 5 Block number selection for Pattern 4 , Step 8 1488 Time signal 6 Block number selection for Pattern 4 , Step 8 1489 Time signal 7 Block number selection for Pattern 4 , Step 8 148A Time signal 8 Block number selection for Pattern 4 , Step 8 148B Wait block number selection to be used for Pattern 4 , Step 8 148C Alarm block number selection to be used for Pattern 4 , Step 8 148D Output block number selection to be used for Pattern 4 , Step 8 1490 Temperature setting value for Pattern 4 , Step 9 1491 Time setting value for Pattern 4 , Step 9 1492 PID block number selection to be used for Pattern 4 , Step 9 1493 Time signal 1 Block number selection to be used for Pattern 4 , Step 9 1494 Time signal 2 Block number selection for Pattern 4 , Step 9 1495 Time signal 3 Block number selection for Pattern 4 , Step 9 1496 Time signal 4 Block number selection for Pattern 4 , Step 9 1497 Time signal 5 Block number selection for Pattern 4 , Step 9 1498 Time signal 6 Block number selection for Pattern 4 , Step 9 1499 Time signal 7 Block number selection for Pattern 4 , Step 9 149A Time signal 8 Block number selection for Pattern 4 , Step 9 149B Wait block number selection to be used for Pattern 4 , Step 9 149C Alarm block number selection to be used for Pattern 4 , Step 9 149D Output block number selection to be used for Pattern 4 , Step 9 1500 Temperature setting value for Pattern 5 , Step 0 1501 Time setting value for Pattern 5 , Step 0 1502 PID block number selection to be used for Pattern 5 , Step 0 1503 Time signal 1 Block number selection to be used for Pattern 5 , Step 0 1504 Time signal 2 Block number selection for Pattern 5 , Step 0 1505 Time signal 3 Block number selection for Pattern 5 , Step 0 1506 Time signal 4 Block number selection for Pattern 5 , Step 0 1507 Time signal 5 Block number selection for Pattern 5 , Step 0 1508 Time signal 6 Block number selection for Pattern 5 , Step 0 1509 Time signal 7 Block number selection for Pattern 5 , Step 0 150A Time signal 8 Block number selection for Pattern 5 , Step 0 150B Wait block number selection to be used for Pattern 5 , Step 0 150C Alarm block number selection to be used for Pattern 5 , Step 0 150D Output block number selection to be used for Pattern 5 , Step 0 1510 Temperature setting value for Pattern 5 , Step 1 1511 Time setting value for Pattern 5 , Step 1 1512 PID block number selection to be used for Pattern 5 , Step 1 1513 Time signal 1 Block number selection to be used for Pattern 5 , Step 1 1514 Time signal 2 Block number selection for Pattern 5 , Step 1 1515 Time signal 3 Block number selection for Pattern 5 , Step 1 1516 Time signal 4 Block number selection for Pattern 5 , Step 1 1517 Time signal 5 Block number selection for Pattern 5 , Step 1 1518 Time signal 6 Block number selection for Pattern 5 , Step 1 1519 Time signal 7 Block number selection for Pattern 5 , Step 1 151A Time signal 8 Block number selection for Pattern 5 , Step 1 151B Wait block number selection to be used for Pattern 5 , Step 1 151C Alarm block number selection to be used for Pattern 5 , Step 1 151D Output block number selection to be used for Pattern 5 , Step 1 1520 Temperature setting value for Pattern 5 , Step 2 1521 Time setting value for Pattern 5 , Step 2 1522 PID block number selection to be used for Pattern 5 , Step 2 1523 Time signal 1 Block number selection to be used for Pattern 5 , Step 2 1524 Time signal 2 Block number selection for Pattern 5 , Step 2 1525 Time signal 3 Block number selection for Pattern 5 , Step 2 1526 Time signal 4 Block number selection for Pattern 5 , Step 2 1527 Time signal 5 Block number selection for Pattern 5 , Step 2 1528 Time signal 6 Block number selection for Pattern 5 , Step 2 1529 Time signal 7 Block number selection for Pattern 5 , Step 2 152A Time signal 8 Block number selection for Pattern 5 , Step 2 152B Wait block number selection to be used for Pattern 5 , Step 2 152C Alarm block number selection to be used for Pattern 5 , Step 2 152D Output block number selection to be used for Pattern 5 , Step 2 1530 Temperature setting value for Pattern 5 , Step 3 1531 Time setting value for Pattern 5 , Step 3 1532 PID block number selection to be used for Pattern 5 , Step 3 1533 Time signal 1 Block number selection to be used for Pattern 5 , Step 3 1534 Time signal 2 Block number selection for Pattern 5 , Step 3 1535 Time signal 3 Block number selection for Pattern 5 , Step 3 1536 Time signal 4 Block number selection for Pattern 5 , Step 3 1537 Time signal 5 Block number selection for Pattern 5 , Step 3 1538 Time signal 6 Block number selection for Pattern 5 , Step 3 1539 Time signal 7 Block number selection for Pattern 5 , Step 3 153A Time signal 8 Block number selection for Pattern 5 , Step 3 153B Wait block number selection to be used for Pattern 5 , Step 3 153C Alarm block number selection to be used for Pattern 5 , Step 3 153D Output block number selection to be used for Pattern 5 , Step 3 1540 Temperature setting value for Pattern 5 , Step 4 1541 Time setting value for Pattern 5 , Step 4 1542 PID block number selection to be used for Pattern 5 , Step 4 1543 Time signal 1 Block number selection to be used for Pattern 5 , Step 4 1544 Time signal 2 Block number selection for Pattern 5 , Step 4 1545 Time signal 3 Block number selection for Pattern 5 , Step 4 1546 Time signal 4 Block number selection for Pattern 5 , Step 4 1547 Time signal 5 Block number selection for Pattern 5 , Step 4 1548 Time signal 6 Block number selection for Pattern 5 , Step 4 1549 Time signal 7 Block number selection for Pattern 5 , Step 4 154A Time signal 8 Block number selection for Pattern 5 , Step 4 154B Wait block number selection to be used for Pattern 5 , Step 4 154C Alarm block number selection to be used for Pattern 5 , Step 4 154D Output block number selection to be used for Pattern 5 , Step 4 1550 Temperature setting value for Pattern 5 , Step 5 1551 Time setting value for Pattern 5 , Step 5 1552 PID block number selection to be used for Pattern 5 , Step 5 1553 Time signal 1 Block number selection to be used for Pattern 5 , Step 5 1554 Time signal 2 Block number selection for Pattern 5 , Step 5 1555 Time signal 3 Block number selection for Pattern 5 , Step 5 1556 Time signal 4 Block number selection for Pattern 5 , Step 5 1557 Time signal 5 Block number selection for Pattern 5 , Step 5 1558 Time signal 6 Block number selection for Pattern 5 , Step 5 1559 Time signal 7 Block number selection for Pattern 5 , Step 5 155A Time signal 8 Block number selection for Pattern 5 , Step 5 155B Wait block number selection to be used for Pattern 5 , Step 5 155C Alarm block number selection to be used for Pattern 5 , Step 5 155D Output block number selection to be used for Pattern 5 , Step 5 1560 Temperature setting value for Pattern 5 , Step 6 1561 Time setting value for Pattern 5 , Step 6 1562 PID block number selection to be used for Pattern 5 , Step 6 1563 Time signal 1 Block number selection to be used for Pattern 5 , Step 6 1564 Time signal 2 Block number selection for Pattern 5 , Step 6 1565 Time signal 3 Block number selection for Pattern 5 , Step 6 1566 Time signal 4 Block number selection for Pattern 5 , Step 6 1567 Time signal 5 Block number selection for Pattern 5 , Step 6 1568 Time signal 6 Block number selection for Pattern 5 , Step 6 1569 Time signal 7 Block number selection for Pattern 5 , Step 6 156A Time signal 8 Block number selection for Pattern 5 , Step 6 156B Wait block number selection to be used for Pattern 5 , Step 6 156C Alarm block number selection to be used for Pattern 5 , Step 6 156D Output block number selection to be used for Pattern 5 , Step 6 1570 Temperature setting value for Pattern 5 , Step 7 1571 Time setting value for Pattern 5 , Step 7 1572 PID block number selection to be used for Pattern 5 , Step 7 1573 Time signal 1 Block number selection to be used for Pattern 5 , Step 7 1574 Time signal 2 Block number selection for Pattern 5 , Step 7 1575 Time signal 3 Block number selection for Pattern 5 , Step 7 1576 Time signal 4 Block number selection for Pattern 5 , Step 7 1577 Time signal 5 Block number selection for Pattern 5 , Step 7 1578 Time signal 6 Block number selection for Pattern 5 , Step 7 1579 Time signal 7 Block number selection for Pattern 5 , Step 7 157A Time signal 8 Block number selection for Pattern 5 , Step 7 157B Wait block number selection to be used for Pattern 5 , Step 7 157C Alarm block number selection to be used for Pattern 5 , Step 7 157D Output block number selection to be used for Pattern 5 , Step 7 1580 Temperature setting value for Pattern 5 , Step 8 1581 Time setting value for Pattern 5 , Step 8 1582 PID block number selection to be used for Pattern 5 , Step 8 1583 Time signal 1 Block number selection to be used for Pattern 5 , Step 8 1584 Time signal 2 Block number selection for Pattern 5 , Step 8 1585 Time signal 3 Block number selection for Pattern 5 , Step 8 1586 Time signal 4 Block number selection for Pattern 5 , Step 8 1587 Time signal 5 Block number selection for Pattern 5 , Step 8 1588 Time signal 6 Block number selection for Pattern 5 , Step 8 1589 Time signal 7 Block number selection for Pattern 5 , Step 8 158A Time signal 8 Block number selection for Pattern 5 , Step 8 158B Wait block number selection to be used for Pattern 5 Step 8 158C Alarm block number selection to be used for Pattern 5 Step 8 158D Output block number selection to be used for Pattern 5 Step 8 1590 Temperature setting value for Pattern 5 , Step 9 1591 Time setting value for Pattern 5 , Step 9 1592 PID block number selection to be used for Pattern 5 , Step 9 1593 Time signal 1 Block number selection to be used for Pattern 5 , Step 9 1594 Time signal 2 Block number selection for Pattern 5 , Step 9 1595 Time signal 3 Block number selection for Pattern 5 , Step 9 1596 Time signal 4 Block number selection for Pattern 5 , Step 9 1597 Time signal 5 Block number selection for Pattern 5 , Step 9 1598 Time signal 6 Block number selection for Pattern 5 , Step 9 1599 Time signal 7 Block number selection for Pattern 5 , Step 9 159A Time signal 8 Block number selection for Pattern 5 , Step 9 159B Wait block number selection to be used for Pattern 5 , Step 9 159C Alarm block number selection to be used for Pattern 5 , Step 9 159D Output block number selection to be used for Pattern 5 , Step 9 1600 Temperature setting value for Pattern 6 , Step 0 1601 Time setting value for Pattern 6 , Step 0 1602 PID block number selection to be used for Pattern 6 , Step 0 1603 Time signal 1 Block number selection to be used for Pattern 6 , Step 0 1604 Time signal 2 Block number selection for Pattern 6 , Step 0 1605 Time signal 3 Block number selection for Pattern 6 , Step 0 1606 Time signal 4 Block number selection for Pattern 6 , Step 0 1607 Time signal 5 Block number selection for Pattern 6 , Step 0 1608 Time signal 6 Block number selection for Pattern 6 , Step 0 1609 Time signal 7 Block number selection for Pattern 6 , Step 0 160A Time signal 8 Block number selection for Pattern 6 , Step 0 160B Wait block number selection to be used for Pattern 6 , Step 0 160C Alarm block number selection to be used for Pattern 6 , Step 0 160D Output block number selection to be used for Pattern 6 , Step 0 1610 Temperature setting value for Pattern 6 , Step 1 1611 Time setting value for Pattern 6 , Step 1 1612 PID block number selection to be used for Pattern 6 , Step 1 1613 Time signal 1 Block number selection to be used for Pattern 6 , Step 1 1614 Time signal 2 Block number selection for Pattern 6 , Step 1 1615 Time signal 3 Block number selection for Pattern 6 , Step 1 1616 Time signal 4 Block number selection for Pattern 6 , Step 1 1617 Time signal 5 Block number selection for Pattern 6 , Step 1 1618 Time signal 6 Block number selection for Pattern 6 , Step 1 1619 Time signal 7 Block number selection for Pattern 6 , Step 1 161A Time signal 8 Block number selection for Pattern 6 , Step 1 161B Wait block number selection to be used for Pattern 6 , Step 1 161C Alarm block number selection to be used for Pattern 6 , Step 1 161D Output block number selection to be used for Pattern 6 , Step 1 1620 Temperature setting value for Pattern 6 , Step 2 1621 Time setting value for Pattern 6 , Step 2 1622 PID block number selection to be used for Pattern 6 , Step 2 1623 Time signal 1 Block number selection to be used for Pattern 6 , Step 2 1624 Time signal 2 Block number selection for Pattern 6 , Step 2 1625 Time signal 3 Block number selection for Pattern 6 , Step 2 1626 Time signal 4 Block number selection for Pattern 6 , Step 2 1627 Time signal 5 Block number selection for Pattern 6 , Step 2 1628 Time signal 6 Block number selection for Pattern 6 , Step 2 1629 Time signal 7 Block number selection for Pattern 6 , Step 2 162A Time signal 8 Block number selection for Pattern 6 , Step 2 162B Wait block number selection to be used for Pattern 6 , Step 2 162C Alarm block number selection to be used for Pattern 6 , Step 2 162D Output block number selection to be used for Pattern 6 , Step 2 1630 Temperature setting value for Pattern 6 , Step 3 1631 Time setting value for Pattern 6 , Step 3 1632 PID block number selection to be used for Pattern 6 , Step 3 1633 Time signal 1 Block number selection to be used for Pattern 6 , Step 3 1634 Time signal 2 Block number selection for Pattern 6 , Step 3 1635 Time signal 3 Block number selection for Pattern 6 , Step 3 1636 Time signal 4 Block number selection for Pattern 6 , Step 3 1637 Time signal 5 Block number selection for Pattern 6 , Step 3 1638 Time signal 6 Block number selection for Pattern 6 , Step 3 1639 Time signal 7 Block number selection for Pattern 6 , Step 3 163A Time signal 8 Block number selection for Pattern 6 , Step 3 163B Wait block number selection to be used for Pattern 6 , Step 3 163C Alarm block number selection to be used for Pattern 6 , Step 3 163D Output block number selection to be used for Pattern 6 , Step 3 1640 Temperature setting value for Pattern 6 , Step 4 1641 Time setting value for Pattern 6 , Step 4 1642 PID block number selection to be used for Pattern 6 , Step 4 1643 Time signal 1 Block number selection to be used for Pattern 6 , Step 4 1644 Time signal 2 Block number selection for Pattern 6 , Step 4 1645 Time signal 3 Block number selection for Pattern 6 , Step 4 1646 Time signal 4 Block number selection for Pattern 6 , Step 4 1647 Time signal 5 Block number selection for Pattern 6 , Step 4 1648 Time signal 6 Block number selection for Pattern 6 , Step 4 1649 Time signal 7 Block number selection for Pattern 6 , Step 4 164A Time signal 8 Block number selection for Pattern 6 , Step 4 164B Wait block number selection to be used for Pattern 6 , Step 4 164C Alarm block number selection to be used for Pattern 6 , Step 4 164D Output block number selection to be used for Pattern 6 , Step 4 1650 Temperature setting value for Pattern 6 , Step 5 1651 Time setting value for Pattern 6 , Step 5 1652 PID block number selection to be used for Pattern 6 , Step 5 1653 Time signal 1 Block number selection to be used for Pattern 6 , Step 5 1654 Time signal 2 Block number selection for Pattern 6 , Step 5 1655 Time signal 3 Block number selection for Pattern 6 , Step 5 1656 Time signal 4 Block number selection for Pattern 6 , Step 5 1657 Time signal 5 Block number selection for Pattern 6 , Step 5 1658 Time signal 6 Block number selection for Pattern 6 , Step 5 1659 Time signal 7 Block number selection for Pattern 6 , Step 5 165A Time signal 8 Block number selection for Pattern 6 , Step 5 165B Wait block number selection to be used for Pattern 6 , Step 5 165C Alarm block number selection to be used for Pattern 6 , Step 5 165D Output block number selection to be used for Pattern 6 , Step 5 1660 Temperature setting value for Pattern 6 , Step 6 1661 Time setting value for Pattern 6 , Step 6 1662 PID block number selection to be used for Pattern 6 , Step 6 1663 Time signal 1 Block number selection to be used for Pattern 6 , Step 6 1664 Time signal 2 Block number selection for Pattern 6 , Step 6 1665 Time signal 3 Block number selection for Pattern 6 , Step 6 1666 Time signal 4 Block number selection for Pattern 6 , Step 6 1667 Time signal 5 Block number selection for Pattern 6 , Step 6 1668 Time signal 6 Block number selection for Pattern 6 , Step 6 1669 Time signal 7 Block number selection for Pattern 6 , Step 6 166A Time signal 8 Block number selection for Pattern 6 , Step 6 166B Wait block number selection to be used for Pattern 6 , Step 6 166C Alarm block number selection to be used for Pattern 6 , Step 6 166D Output block number selection to be used for Pattern 6 , Step 6 1670 Temperature setting value for Pattern 6 , Step 7 1671 Time setting value for Pattern 6 , Step 7 1672 PID block number selection to be used for Pattern 6 , Step 7 1673 Time signal 1 Block number selection to be used for Pattern 6 , Step 7 1674 Time signal 2 Block number selection for Pattern 6 , Step 7 1675 Time signal 3 Block number selection for Pattern 6 , Step 7 1676 Time signal 4 Block number selection for Pattern 6 , Step 7 1677 Time signal 5 Block number selection for Pattern 6 , Step 7 1678 Time signal 6 Block number selection for Pattern 6 , Step 7 1679 Time signal 7 Block number selection for Pattern 6 , Step 7 167A Time signal 8 Block number selection for Pattern 6 , Step 7 167B Wait block number selection to be used for Pattern 6 , Step 7 167C Alarm block number selection to be used for Pattern 6 , Step 7 167D Output block number selection to be used for Pattern 6 , Step 7 1680 Temperature setting value for Pattern 6 , Step 8 1681 Time setting value for Pattern 6 , Step 8 1682 PID block number selection to be used for Pattern 6 , Step 8 1683 Time signal 1 Block number selection to be used for Pattern 6 , Step 8 1684 Time signal 2 Block number selection for Pattern 6 , Step 8 1685 Time signal 3 Block number selection for Pattern 6 , Step 8 1686 Time signal 4 Block number selection for Pattern 6 , Step 8 1687 Time signal 5 Block number selection for Pattern 6 , Step 8 1688 Time signal 6 Block number selection for Pattern 6 , Step 8 1689 Time signal 7 Block number selection for Pattern 6 , Step 8 168A Time signal 8 Block number selection for Pattern 6 , Step 8 168B Wait block number selection to be used for Pattern 6 , Step 8 168C Alarm block number selection to be used for Pattern 6 , Step 8 168D Output block number selection to be used for Pattern 6 , Step 8 1690 Temperature setting value for Pattern 6 , Step 9 1691 Time setting value for Pattern 6 , Step 9 1692 PID block number selection to be used for Pattern 6 , Step 9 1693 Time signal 1 Block number selection to be used for Pattern 6 , Step 9 1694 Time signal 2 Block number selection for Pattern 6 , Step 9 1695 Time signal 3 Block number selection for Pattern 6 , Step 9 1696 Time signal 4 Block number selection for Pattern 6 , Step 9 1697 Time signal 5 Block number selection for Pattern 6 , Step 9 1698 Time signal 6 Block number selection for Pattern 6 , Step 9 1699 Time signal 7 Block number selection for Pattern 6 , Step 9 169A Time signal 8 Block number selection for Pattern 6 , Step 9 169B Wait block number selection to be used for Pattern 6 , Step 9 169C Alarm block number selection to be used for Pattern 6 , Step 9 169D Output block number selection to be used for Pattern 6 , Step 9 1700 Temperature setting value for Pattern 7 , Step 0 1701 Time setting value for Pattern 7 , Step 0 1702 PID block number selection to be used for Pattern 7 , Step 0 1703 Time signal 1 Block number selection to be used for Pattern 7 , Step 0 1704 Time signal 2 Block number selection for Pattern 7 , Step 0 1705 Time signal 3 Block number selection for Pattern 7 , Step 0 1706 Time signal 4 Block number selection for Pattern 7 , Step 0 1707 Time signal 5 Block number selection for Pattern 7 , Step 0 1708 Time signal 6 Block number selection for Pattern 7 , Step 0 1709 Time signal 7 Block number selection for Pattern 7 , Step 0 170A Time signal 8 Block number selection for Pattern 7 , Step 0 170B Wait block number selection to be used for Pattern 7 , Step 0 170C Alarm block number selection to be used for Pattern 7 , Step 0 170D Output block number selection to be used for Pattern 7 , Step 0 1710 Temperature setting value for Pattern 7 , Step 1 1711 Time setting value for Pattern 7 , Step 1 1712 PID block number selection to be used for Pattern 7 , Step 1 1713 Time signal 1 Block number selection to be used for Pattern 7 , Step 1 1714 Time signal 2 Block number selection for Pattern 7 , Step 1 1715 Time signal 3 Block number selection for Pattern 7 , Step 1 1716 Time signal 4 Block number selection for Pattern 7 , Step 1 1717 Time signal 5 Block number selection for Pattern 7 , Step 1 1718 Time signal 6 Block number selection for Pattern 7 , Step 1 1719 Time signal 7 Block number selection for Pattern 7 , Step 1 171A Time signal 8 Block number selection for Pattern 7 , Step 1 171B Wait block number selection to be used for Pattern 7 , Step 1 171C Alarm block number selection to be used for Pattern 7 , Step 1 171D Output block number selection to be used for Pattern 7 , Step 1 1720 Temperature setting value for Pattern 7 , Step 2 1721 Time setting value for Pattern 7 , Step 2 1722 PID block number selection to be used for Pattern 7 , Step 2 1723 Time signal 1 Block number selection to be used for Pattern 7 , Step 2 1724 Time signal 2 Block number selection for Pattern 7 , Step 2 1725 Time signal 3 Block number selection for Pattern 7 , Step 2 1726 Time signal 4 Block number selection for Pattern 7 , Step 2 1727 Time signal 5 Block number selection for Pattern 7 , Step 2 1728 Time signal 6 Block number selection for Pattern 7 , Step 2 1729 Time signal 7 Block number selection for Pattern 7 , Step 2 172A Time signal 8 Block number selection for Pattern 7 , Step 2 172B Wait block number selection to be used for Pattern 7 , Step 2 172C Alarm block number selection to be used for Pattern 7 , Step 2 172D Output block number selection to be used for Pattern 7 , Step 2 1730 Temperature setting value for Pattern 7 , Step 3 1731 Time setting value for Pattern 7 , Step 3 1732 PID block number selection to be used for Pattern 7 , Step 3 1733 Time signal 1 Block number selection to be used for Pattern 7 , Step 3 1734 Time signal 2 Block number selection for Pattern 7 , Step 3 1735 Time signal 3 Block number selection for Pattern 7 , Step 3 1736 Time signal 4 Block number selection for Pattern 7 , Step 3 1737 Time signal 5 Block number selection for Pattern 7 , Step 3 1738 Time signal 6 Block number selection for Pattern 7 , Step 3 1739 Time signal 7 Block number selection for Pattern 7 , Step 3 173A Time signal 8 Block number selection for Pattern 7 , Step 3 173B Wait block number selection to be used for Pattern 7 , Step 3 173C Alarm block number selection to be used for Pattern 7 , Step 3 173D Output block number selection to be used for Pattern 7 , Step 3 1740 Temperature setting value for Pattern 7 , Step 4 1741 Time setting value for Pattern 7 , Step 4 1742 PID block number selection to be used for Pattern 7 , Step 4 1743 Time signal 1 Block number selection to be used for Pattern 7 , Step 4 1744 Time signal 2 Block number selection for Pattern 7 , Step 4 1745 Time signal 3 Block number selection for Pattern 7 , Step 4 1746 Time signal 4 Block number selection for Pattern 7 , Step 4 1747 Time signal 5 Block number selection for Pattern 7 , Step 4 1748 Time signal 6 Block number selection for Pattern 7 , Step 4 1749 Time signal 7 Block number selection for Pattern 7 , Step 4 174A Time signal 8 Block number selection for Pattern 7 , Step 4 174B Wait block number selection to be used for Pattern 7 , Step 4 174C Alarm block number selection to be used for Pattern 7 , Step 4 174D Output block number selection to be used for Pattern 7 , Step 4 1750 Temperature setting value for Pattern 7 , Step 5 1751 Time setting value for Pattern 7 , Step 5 1752 PID block number selection to be used for Pattern 7 , Step 5 1753 Time signal 1 Block number selection to be used for Pattern 7 , Step 5 1754 Time signal 2 Block number selection for Pattern 7 , Step 5 1755 Time signal 3 Block number selection for Pattern 7 , Step 5 1756 Time signal 4 Block number selection for Pattern 7 , Step 5 1757 Time signal 5 Block number selection for Pattern 7 , Step 5 1758 Time signal 6 Block number selection for Pattern 7 , Step 5 1759 Time signal 7 Block number selection for Pattern 7 , Step 5 175A Time signal 8 Block number selection for Pattern 7 , Step 5 175B Wait block number selection to be used for Pattern 7 , Step 5 175C Alarm block number selection to be used for Pattern 7 , Step 5 175D Output block number selection to be used for Pattern 7 , Step 5 1760 Temperature setting value for Pattern 7 , Step 6 1761 Time setting value for Pattern 7 , Step 6 1762 PID block number selection to be used for Pattern 7 , Step 6 1763 Time signal 1 Block number selection to be used for Pattern 7 , Step 6 1764 Time signal 2 Block number selection for Pattern 7 , Step 6 1765 Time signal 3 Block number selection for Pattern 7 , Step 6 1766 Time signal 4 Block number selection for Pattern 7 , Step 6 1767 Time signal 5 Block number selection for Pattern 7 , Step 6 1768 Time signal 6 Block number selection for Pattern 7 , Step 6 1769 Time signal 7 Block number selection for Pattern 7 , Step 6 176A Time signal 8 Block number selection for Pattern 7 , Step 6 176B Wait block number selection to be used for Pattern 7 , Step 6 176C Alarm block number selection to be used for Pattern 7 , Step 6 176D Output block number selection to be used for Pattern 7 , Step 6 1770 Temperature setting value for Pattern 7 , Step 7 1771 Time setting value for Pattern 7 , Step 7 1772 PID block number selection to be used for Pattern 7 , Step 7 1773 Time signal 1 Block number selection to be used for Pattern 7 , Step 7 1774 Time signal 2 Block number selection for Pattern 7 , Step 7 1775 Time signal 3 Block number selection for Pattern 7 , Step 7 1776 Time signal 4 Block number selection for Pattern 7 , Step 7 1777 Time signal 5 Block number selection for Pattern 7 , Step 7 1778 Time signal 6 Block number selection for Pattern 7 , Step 7 1779 Time signal 7 Block number selection for Pattern 7 , Step 7 177A Time signal 8 Block number selection for Pattern 7 , Step 7 177B Wait block number selection to be used for Pattern 7 , Step 7 177C Alarm block number selection to be used for Pattern 7 , Step 7 177D Output block number selection to be used for Pattern 7 , Step 7 1780 Temperature setting value for Pattern 7 , Step 8 1781 Time setting value for Pattern 7 , Step 8 1782 PID block number selection to be used for Pattern 7 , Step 8 1783 Time signal 1 Block number selection to be used for Pattern 7 , Step 8 1784 Time signal 2 Block number selection for Pattern 7 , Step 8 1785 Time signal 3 Block number selection for Pattern 7 , Step 8 1786 Time signal 4 Block number selection for Pattern 7 , Step 8 1787 Time signal 5 Block number selection for Pattern 7 , Step 8 1788 Time signal 6 Block number selection for Pattern 7 , Step 8 1789 Time signal 7 Block number selection for Pattern 7 , Step 8 178A Time signal 8 Block number selection for Pattern 7 , Step 8 178B Wait block number selection to be used for Pattern 7 , Step 8 178C Alarm block number selection to be used for Pattern 7 , Step 8 178D Output block number selection to be used for Pattern 7 , Step 8 1790 Temperature setting value for Pattern 7 , Step 9 1791 Time setting value for Pattern 7 , Step 9 1792 PID block number selection to be used for Pattern 7 , Step 9 1793 Time signal 1 Block number selection to be used for Pattern 7 , Step 9 1794 Time signal 2 Block number selection for Pattern 7 , Step 9 1795 Time signal 3 Block number selection for Pattern 7 , Step 9 1796 Time signal 4 Block number selection for Pattern 7 , Step 9 1797 Time signal 5 Block number selection for Pattern 7 , Step 9 1798 Time signal 6 Block number selection for Pattern 7 , Step 9 1799 Time signal 7 Block number selection for Pattern 7 , Step 9 179A Time signal 8 Block number selection for Pattern 7 , Step 9 179B Wait block number selection to be used for Pattern 7 , Step 9 179C Alarm block number selection to be used for Pattern 7 , Step 9 179D Output block number selection to be used for Pattern 7 , Step 9 1800 Temperature setting value for Pattern 8 , Step 0 1801 Time setting value for Pattern 8 , Step 0 1802 PID block number selection to be used for Pattern 8 , Step 0 1803 Time signal 1 Block number selection to be used for Pattern 8 , Step 0 1804 Time signal 2 Block number selection for Pattern 8 , Step 0 1805 Time signal 3 Block number selection for Pattern 8 , Step 0 1806 Time signal 4 Block number selection for Pattern 8 , Step 0 1807 Time signal 5 Block number selection for Pattern 8 , Step 0 1808 Time signal 6 Block number selection for Pattern 8 , Step 0 1809 Time signal 7 Block number selection for Pattern 8 , Step 0 180A Time signal 8 Block number selection for Pattern 8 , Step 0 180B Wait block number selection to be used for Pattern 8 , Step 0 180C Alarm block number selection to be used for Pattern 8 , Step 0 180D Output block number selection to be used for Pattern 8 , Step 0 1810 Temperature setting value for Pattern 8 , Step 1 1811 Time setting value for Pattern 8 , Step 1 1812 PID block number selection to be used for Pattern 8 , Step 1 1813 Time signal 1 Block number selection to be used for Pattern 8 , Step 1 1814 Time signal 2 Block number selection for Pattern 8 , Step 1 1815 Time signal 3 Block number selection for Pattern 8 , Step 1 1816 Time signal 4 Block number selection for Pattern 8 , Step 1 1817 Time signal 5 Block number selection for Pattern 8 , Step 1 1818 Time signal 6 Block number selection for Pattern 8 , Step 1 1819 Time signal 7 Block number selection for Pattern 8 , Step 1 181A Time signal 8 Block number selection for Pattern 8 , Step 1 181B Wait block number selection to be used for Pattern 8 , Step 1 181C Alarm block number selection to be used for Pattern 8 , Step 1 181D Output block number selection to be used for Pattern 8 , Step 1 1820 Temperature setting value for Pattern 8 , Step 2 1821 Time setting value for Pattern 8 , Step 2 1822 PID block number selection to be used for Pattern 8 , Step 2 1823 Time signal 1 Block number selection to be used for Pattern 8 , Step 2 1824 Time signal 2 Block number selection for Pattern 8 , Step 2 1825 Time signal 3 Block number selection for Pattern 8 , Step 2 1826 Time signal 4 Block number selection for Pattern 8 , Step 2 1827 Time signal 5 Block number selection for Pattern 8 , Step 2 1828 Time signal 6 Block number selection for Pattern 8 , Step 2 1829 Time signal 7 Block number selection for Pattern 8 , Step 2 182A Time signal 8 Block number selection for Pattern 8 , Step 2 182B Wait block number selection to be used for Pattern 8 , Step 2 182C Alarm block number selection to be used for Pattern 8 , Step 2 182D Output block number selection to be used for Pattern 8 , Step 2 1830 Temperature setting value for Pattern 8 , Step 3 1831 Time setting value for Pattern 8 , Step 3 1832 PID block number selection to be used for Pattern 8 , Step 3 1833 Time signal 1 Block number selection to be used for Pattern 8 , Step 3 1834 Time signal 2 Block number selection for Pattern 8 , Step 3 1835 Time signal 3 Block number selection for Pattern 8 , Step 3 1836 Time signal 4 Block number selection for Pattern 8 , Step 3 1837 Time signal 5 Block number selection for Pattern 8 , Step 3 1838 Time signal 6 Block number selection for Pattern 8 , Step 3 1839 Time signal 7 Block number selection for Pattern 8 , Step 3 183A Time signal 8 Block number selection for Pattern 8 , Step 3 183B Wait block number selection to be used for Pattern 8 , Step 3 183C Alarm block number selection to be used for Pattern 8 , Step 3 183D Output block number selection to be used for Pattern 8 , Step 3 1840 Temperature setting value for Pattern 8 , Step 4 1841 Time setting value for Pattern 8 , Step 4 1842 PID block number selection to be used for Pattern 8 , Step 4 1843 Time signal 1 Block number selection for Pattern 8 , Step 4 1844 Time signal 2 Block number selection for Pattern 8 , Step 4 1845 Time signal 3 Block number selection for Pattern 8 , Step 4 1846 Time signal 4 Block number selection for Pattern 8 , Step 4 1847 Time signal 5 Block number selection for Pattern 8 , Step 4 1848 Time signal 6 Block number selection for Pattern 8 , Step 4 1849 Time signal 7 Block number selection for Pattern 8 , Step 4 184A Time signal 8 Block number selection for Pattern 8 , Step 4 184B Wait block number selection to be used for Pattern 8 , Step 4 184C Alarm block number selection to be used for Pattern 8 , Step 4 184D Output block number selection to be used for Pattern 8 , Step 4 1850 Temperature setting value for Pattern 8 , Step 5 1851 Time setting value for Pattern 8 , Step 5 1852 PID block number selection to be used for Pattern 8 , Step 5 1853 Time signal 1 Block number selection to be used for Pattern 8 , Step 5 1854 Time signal 2 Block number selection for Pattern 8 , Step 5 1855 Time signal 3 Block number selection for Pattern 8 , Step 5 1856 Time signal 4 Block number selection for Pattern 8 , Step 5 1857 Time signal 5 Block number selection for Pattern 8 , Step 5 1858 Time signal 6 Block number selection for Pattern 8 , Step 5 1859 Time signal 7 Block number selection for Pattern 8 , Step 5 185A Time signal 8 Block number selection for Pattern 8 , Step 5 185B Wait block number selection to be used for Pattern 8 , Step 5 185C Alarm block number selection to be used for Pattern 8 , Step 5 185D Output block number selection to be used for Pattern 8 , Step 5 1860 Temperature setting value for Pattern 8 , Step 6 1861 Time setting value for Pattern 8 , Step 6 1862 PID block number selection to be used for Pattern 8 , Step 6 1863 Time signal 1 Block number selection to be used for Pattern 8 , Step 6 1864 Time signal 2 Block number selection for Pattern 8 , Step 6 1865 Time signal 3 Block number selection for Pattern 8 , Step 6 1866 Time signal 4 Block number selection for Pattern 8 , Step 6 1867 Time signal 5 Block number selection for Pattern 8 , Step 6 1868 Time signal 6 Block number selection for Pattern 8 , Step 6 1869 Time signal 7 Block number selection for Pattern 8 , Step 6 186A Time signal 8 Block number selection for Pattern 8 , Step 6 186B Wait block number selection to be used for Pattern 8 , Step 6 186C Alarm block number selection to be used for Pattern 8 , Step 6 186D Output block number selection to be used for Pattern 8 , Step 6 1870 Temperature setting value for Pattern 8 , Step 7 1871 Time setting value for Pattern 8 , Step 7 1872 PID block number selection to be used for Pattern 8 , Step 7 1873 Time signal 1 Block number selection to be used for Pattern 8 , Step 7 1874 Time signal 2 Block number selection for Pattern 8 , Step 7 1875 Time signal 3 Block number selection for Pattern 8 , Step 7 1876 Time signal 4 Block number selection for Pattern 8 , Step 7 1877 Time signal 5 Block number selection for Pattern 8 , Step 7 1878 Time signal 6 Block number selection for Pattern 8 , Step 7 1879 Time signal 7 Block number selection for Pattern 8 , Step 7 187A Time signal 8 Block number selection for Pattern 8 , Step 7 187B Wait block number selection to be used for Pattern 8 , Step 7 187C Alarm block number selection to be used for Pattern 8 , Step 7 187D Output block number selection to be used for Pattern 8 , Step 7 1880 Temperature setting value for Pattern 8 , Step 8 1881 Time setting value for Pattern 8 , Step 8 1882 PID block number selection to be used for Pattern 8 , Step 8 1883 Time signal 1 Block number selection to be used for Pattern 8 , Step 8 1884 Time signal 2 Block number selection for Pattern 8 , Step 8 1885 Time signal 3 Block number selection for Pattern 8 , Step 8 1886 Time signal 4 Block number selection for Pattern 8 , Step 8 1887 Time signal 5 Block number selection for Pattern 8 , Step 8 1888 Time signal 6 Block number selection for Pattern 8 , Step 8 1889 Time signal 7 Block number selection for Pattern 8 , Step 8 188A Time signal 8 Block number selection for Pattern 8 , Step 8 188B Wait block number selection to be used for Pattern 8 , Step 8 188C Alarm block number selection to be used for Pattern 8 , Step 8 188D Output block number selection to be used for Pattern 8 , Step 8 1890 Temperature setting value for Pattern 8 , Step 9 1891 Time setting value for Pattern 8 , Step 9 1892 PID block number selection to be used for Pattern 8 , Step 9 1893 Time signal 1 Block number selection to be used for Pattern 8 , Step 9 1894 Time signal 2 Block number selection for Pattern 8 , Step 9 1895 Time signal 3 Block number selection for Pattern 8 , Step 9 1896 Time signal 4 Block number selection for Pattern 8 , Step 9 1897 Time signal 5 Block number selection for Pattern 8 , Step 9 1898 Time signal 6 Block number selection for Pattern 8 , Step 9 1899 Time signal 7 Block number selection for Pattern 8 , Step 9 189A Time signal 8 Block number selection for Pattern 8 , Step 9 189B Wait block number selection to be used for Pattern 8 , Step 9 189C Alarm block number selection to be used for Pattern 8 , Step 9 189D Output block number selection to be used for Pattern 8 , Step 9 1900 Temperature setting value for Pattern 9 , Step 0 1901 Time setting value for Pattern 9 , Step 0 1902 PID block number selection to be used for Pattern 9 , Step 0 1903 Time signal 1 Block number selection to be used for Pattern 9 , Step 0 1904 Time signal 2 Block number selection for Pattern 9 , Step 0 1905 Time signal 3 Block number selection for Pattern 9 , Step 0 1906 Time signal 4 Block number selection for Pattern 9 , Step 0 1907 Time signal 5 Block number selection for Pattern 9 , Step 0 1908 Time signal 6 Block number selection for Pattern 9 , Step 0 1909 Time signal 7 Block number selection for Pattern 9 , Step 0 190A Time signal 8 Block number selection for Pattern 9 , Step 0 190B Wait block number selection to be used for Pattern 9 , Step 0 190C Alarm block number selection to be used for Pattern 9 , Step 0 190D Output block number selection to be used for Pattern 9 , Step 0 1910 Temperature setting value for Pattern 9 , Step 1 1911 Time setting value for Pattern 9 , Step 1 1912 PID block number selection to be used for Pattern 9 , Step 1 1913 Time signal 1 Block number selection to be used for Pattern 9 , Step 1 1914 Time signal 2 Block number selection for Pattern 9 , Step 1 1915 Time signal 3 Block number selection for Pattern 9 , Step 1 1916 Time signal 4 Block number selection for Pattern 9 , Step 1 1917 Time signal 5 Block number selection for Pattern 9 , Step 1 1918 Time signal 6 Block number selection for Pattern 9 , Step 1 1919 Time signal 7 Block number selection for Pattern 9 , Step 1 191A Time signal 8 Block number selection for Pattern 9 , Step 1 191B Wait block number selection to be used for Pattern 9 , Step 1 191C Alarm block number selection to be used for Pattern 9 , Step 1 191D Output block number selection to be used for Pattern 9 , Step 1 1920 Temperature setting value for Pattern 9 , Step 2 1921 Time setting value for Pattern 9 , Step 2 1922 PID block number selection to be used for Pattern 9 , Step 2 1923 Time signal 1 Block number selection to be used for Pattern 9 , Step 2 1924 Time signal 2 Block number selection for Pattern 9 , Step 2 1925 Time signal 3 Block number selection for Pattern 9 , Step 2 1926 Time signal 4 Block number selection for Pattern 9 , Step 2 1927 Time signal 5 Block number selection for Pattern 9 , Step 2 1928 Time signal 6 Block number selection for Pattern 9 , Step 2 1929 Time signal 7 Block number selection for Pattern 9 , Step 2 192A Time signal 8 Block number selection for Pattern 9 , Step 2 192B Wait block number selection to be used for Pattern 9 , Step 2 192C Alarm block number selection to be used for Pattern 9 , Step 2 192D Output block number selection to be used for Pattern 9 , Step 2 1930 Temperature setting value for Pattern 9 , Step 3 1931 Time setting value for Pattern 9 , Step 3 1932 PID block number selection to be used for Pattern 9 , Step 3 1933 Time signal 1 Block number selection to be used for Pattern 9 , Step 3 1934 Time signal 2 Block number selection for Pattern 9 , Step 3 1935 Time signal 3 Block number selection for Pattern 9 , Step 3 1936 Time signal 4 Block number selection for Pattern 9 , Step 3 1937 Time signal 5 Block number selection for Pattern 9 , Step 3 1938 Time signal 6 Block number selection for Pattern 9 , Step 3 1939 Time signal 7 Block number selection for Pattern 9 , Step 3 193A Time signal 8 Block number selection for Pattern 9 , Step 3 193B Wait block number selection to be used for Pattern 9 , Step 3 193C Alarm block number selection to be used for Pattern 9 , Step 3 193D Output block number selection to be used for Pattern 9 , Step 3 1940 Temperature setting value for Pattern 9 , Step 4 1941 Time setting value for Pattern 9 , Step 4 1942 PID block number selection to be used for Pattern 9 , Step 4 1943 Time signal 1 Block number selection to be used for Pattern 9 , Step 4 1944 Time signal 2 Block number selection for Pattern 9 , Step 4 1945 Time signal 3 Block number selection for Pattern 9 , Step 4 1946 Time signal 4 Block number selection for Pattern 9 , Step 4 1947 Time signal 5 Block number selection for Pattern 9 , Step 4 1948 Time signal 6 Block number selection for Pattern 9 , Step 4 1949 Time signal 7 Block number selection for Pattern 9 , Step 4 194A Time signal 8 Block number selection for Pattern 9 , Step 4 194B Wait block number selection to be used for Pattern 9 , Step 4 194C Alarm block number selection to be used for Pattern 9 , Step 4 194D Output block number selection to be used for Pattern 9 , Step 4 1950 Temperature setting value for Pattern 9 , Step 5 1951 Time setting value for Pattern 9 , Step 5 1952 PID block number selection to be used for Pattern 9 , Step 5 1953 Time signal 1 Block number selection to be used for Pattern 9 , Step 5 1954 Time signal 2 Block number selection for Pattern 9 , Step 5 1955 Time signal 3 Block number selection for Pattern 9 , Step 5 1956 Time signal 4 Block number selection for Pattern 9 , Step 5 1957 Time signal 5 Block number selection for Pattern 9 , Step 5 1958 Time signal 6 Block number selection for Pattern 9 , Step 5 1959 Time signal 7 Block number selection for Pattern 9 , Step 5 195A Time signal 8 Block number selection for Pattern 9 , Step 5 195B Wait block number selection to be used for Pattern 9 , Step 5 195C Alarm block number selection to be used for Pattern 9 , Step 5 195D Output block number selection to be used for Pattern 9 , Step 5 1960 Temperature setting value for Pattern 9 , Step 6 1961 Time setting value for Pattern 9 , Step 6 1962 PID block number selection to be used for Pattern 9 , Step 6 1963 Time signal 1 Block number selection to be used for Pattern 9 , Step 6 1964 Time signal 2 Block number selection for Pattern 9 , Step 6 1965 Time signal 3 Block number selection for Pattern 9 , Step 6 1966 Time signal 4 Block number selection for Pattern 9 , Step 6 1967 Time signal 5 Block number selection for Pattern 9 , Step 6 1968 Time signal 6 Block number selection for Pattern 9 , Step 6 1969 Time signal 7 Block number selection for Pattern 9 , Step 6 196A Time signal 8 Block number selection for Pattern 9 , Step 6 196B Wait block number selection to be used for Pattern 9 , Step 6 196C Alarm block number selection to be used for Pattern 9 , Step 6 196D Output block number selection to be used for Pattern 9 , Step 6 1970 Temperature setting value for Pattern 9 , Step 7 1971 Time setting value for Pattern 9 , Step 7 1972 PID block number selection to be used for Pattern 9 , Step 7 1973 Time signal 1 Block number selection to be used for Pattern 9 , Step 7 1974 Time signal 2 Block number selection for Pattern 9 , Step 7 1975 Time signal 3 Block number selection for Pattern 9 , Step 7 1976 Time signal 4 Block number selection for Pattern 9 , Step 7 1977 Time signal 5 Block number selection for Pattern 9 , Step 7 1978 Time signal 6 Block number selection for Pattern 9 , Step 7 1979 Time signal 7 Block number selection for Pattern 9 , Step 7 197A Time signal 8 Block number selection for Pattern 9 , Step 7 197B Wait block number selection to be used for Pattern 9 , Step 7 197C Alarm block number selection to be used for Pattern 9 , Step 7 197D Output block number selection to be used for Pattern 9 , Step 7 1980 Temperature setting value for Pattern 9 , Step 8 1981 Time setting value for Pattern 9 , Step 8 1982 PID block number selection to be used for Pattern 9 , Step 8 1983 Time signal 1 Block number selection to be used for Pattern 9 , Step 8 1984 Time signal 2 Block number selection for Pattern 9 , Step 8 1985 Time signal 3 Block number selection for Pattern 9 , Step 8 1986 Time signal 4 Block number selection for Pattern 9 , Step 8 1987 Time signal 5 Block number selection for Pattern 9 , Step 8 1988 Time signal 6 Block number selection for Pattern 9 , Step 8 1989 Time signal 7 Block number selection for Pattern 9 , Step 8 198A Time signal 8 Block number selection for Pattern 9 , Step 8 198B Wait block number selection to be used for Pattern 9 , Step 8 198C Alarm block number selection to be used for Pattern 9 , Step 8 198D Output block number selection to be used for Pattern 9 , Step 8 1990 Temperature setting value for Pattern 9 , Step 9 1991 Time setting value for Pattern 9 , Step 9 1992 PID block number selection to be used for Pattern 9 , Step 9 1993 Time signal 1 Block number selection to be used for Pattern 9 , Step 9 1994 Time signal 2 Block number selection for Pattern 9 , Step 9 1995 Time signal 3 Block number selection for Pattern 9 , Step 9 1996 Time signal 4 Block number selection for Pattern 9 , Step 9 1997 Time signal 5 Block number selection for Pattern 9 , Step 9 1998 Time signal 6 Block number selection for Pattern 9 , Step 9 1999 Time signal 7 Block number selection for Pattern 9 , Step 9 199A Time signal 8 Block number selection for Pattern 9 , Step 9 199B Wait block number selection to be used for Pattern 9 , Step 9 199C Alarm block number selection to be used for Pattern 9 , Step 9 199D Output block number selection to be used for Pattern 9 , Step 9 2000 Control output (OUT1) Proportional band setting for Block number 0 2001 Integral time setting for Block number 0 2002 Derivative time setting for Block number 0 2003 Anti-reset windup setting for Block number 0 2004 Control output (OUT2) Proportional band setting for Block number 0 2100 Control output (OUT1) Proportional band setting for Block number 1 2101 Integral time setting for Block number 1 2102 Derivative time setting for Block number 1 2103 Anti-reset windup setting for Block number 1 2104 Control output (OUT2) Proportional band setting for Block number 1 2200 Control output (OUT1) Proportional band setting for Block number 2 2201 Integral time setting for Block number 2 2202 Derivative time setting for Block number 2 2203 Anti-reset windup setting for Block number 2 2204 Control output (OUT2) Proportional band setting for Block number 2 2300 Control output (OUT1) Proportional band setting for Block number 3 2301 Integral time setting for Block number 3 2302 Derivative time setting for Block number 3 2303 Anti-reset windup setting for Block number 3 2304 Control output (OUT2) Proportional band setting for Block number 3 2400 Control output (OUT1) Proportional band setting for Block number 4 2401 Integral time setting for Block number 4 2402 Derivative time setting for Block number 4 2403 Anti-reset windup setting for Block number 4 2404 Control output (OUT2) Proportional band setting for Block number 4 2500 Control output (OUT1) Proportional band setting for Block number 5 2501 Integral time setting for Block number 5 2502 Derivative time setting for Block number 5 2503 Anti-reset windup setting for Block number 5 2504 Control output (OUT2) Proportional band setting for Block number 5 2600 Control output (OUT1) Proportional band setting for Block number 6 2601 Integral time setting for Block number 6 2602 Derivative time setting for Block number 6 2603 Anti-reset windup setting for Block number 6 2604 Control output (OUT2) Proportional band setting for Block number 6 2700 Control output (OUT1) Proportional band setting for Block number 7 2701 Integral time setting for Block number 7 2702 Derivative time setting for Block number 7 2703 Anti-reset windup setting for Block number 7 2704 Control output (OUT2) Proportional band setting for Block number 7 2800 Control output (OUT1) Proportional band setting for Block number 8 2801 Integral time setting for Block number 8 2802 Derivative time setting for Block number 8 2803 Anti-reset windup setting for Block number 8 2804 Control output (OUT2) Proportional band setting for Block number 8 2900 Control output (OUT1) Proportional band setting for Block number 9 2901 Integral time setting for Block number 9 2902 Derivative time setting for Block number 9 2903 Anti-reset windup setting for Block number 9 2904 Control output (OUT2) Proportional band setting for Block number 9 3000 Wait value setting for Block number 0 3100 Wait value setting for Block number 1 3200 Wait value setting for Block number 2 3300 Wait value setting for Block number 3 3400 Wait value setting for Block number 4 3500 Wait value setting for Block number 5 3600 Wait value setting for Block number 6 3700 Wait value setting for Block number 7 3800 Wait value setting for Block number 8 3900 Wait value setting for Block number 9 4000 Alarm 1 action point setting for Block number 0 4001 Alarm 2 action point setting for Block number 0 4002 Alarm 3 action point setting for Block number 0 4003 Alarm 4 action point setting for Block number 0 4100 Alarm 1 action point setting for Block number 1 4101 Alarm 2 action point setting for Block number 1 4102 Alarm 3 action point setting for Block number 1 4103 Alarm 4 action point setting for Block number 1 4200 Alarm 1 action point setting for Block number 2 4201 Alarm 2 action point setting for Block number 2 4202 Alarm 3 action point setting for Block number 2 4203 Alarm 4 action point setting for Block number 2 4300 Alarm 1 action point setting for Block number 3 4301 Alarm 2 action point setting for Block number 3 4302 Alarm 3 action point setting for Block number 3 4303 Alarm 4 action point setting for Block number 3 4400 Alarm 1 action point setting for Block number 4 4401 Alarm 2 action point setting for Block number 4 4402 Alarm 3 action point setting for Block number 4 4403 Alarm 4 action point setting for Block number 4 4500 Alarm 1 action point setting for Block number 5 4501 Alarm 2 action point setting for Block number 5 4502 Alarm 3 action point setting for Block number 5 4503 Alarm 4 action point setting for Block number 5 4600 Alarm 1 action point setting for Block number 6 4601 Alarm 2 action point setting for Block number 6 4602 Alarm 3 action point setting for Block number 6 4603 Alarm 4 action point setting for Block number 6 4700 Alarm 1 action point setting for Block number 7 4701 Alarm 2 action point setting for Block number 7 4702 Alarm 3 action point setting for Block number 7 4703 Alarm 4 action point setting for Block number 7 4800 Alarm 1 action point setting for Block number 8 4801 Alarm 2 action point setting for Block number 8 4802 Alarm 3 action point setting for Block number 8 4803 Alarm 4 action point setting for Block number 8 4900 Alarm 1 action point setting for Block number 9 4901 Alarm 2 action point setting for Block number 9 4902 Alarm 3 action point setting for Block number 9 4903 Alarm 4 action point setting for Block number 9 5000 Control output (OUT1) high limit setting for Block number 0 5001 Control output (OUT1) low limit setting for Block number 0 5002 Control output (OUT2) high limit setting for Block number 0 5003 Control output (OUT2) low limit setting for Block number 0 5004 Control output (OUT1) changing rate limit setting for Block number 0 5100 Control output (OUT1) high limit setting for Block number 1 5101 Control output (OUT1) low limit setting for Block number 1 5102 Control output (OUT2) high limit setting for Block number 1 5103 Control output (OUT2) low limit setting for Block number 1 5104 Control output (OUT1) changing rate limit setting for Block number 1 5200 Control output (OUT1) high limit setting for Block number 2 5201 Control output (OUT1) low limit setting for Block number 2 5202 Control output (OUT2) high limit setting for Block number 2 5203 Control output (OUT2) low limit setting for Block number 2 5204 Control output (OUT1) changing rate limit setting for Block number 2 5300 Control output (OUT1) high limit setting for Block number 3 5301 Control output (OUT1) low limit setting for Block number 3 5302 Control output (OUT2) high limit setting for Block number 3 5303 Control output (OUT2) low limit setting for Block number 3 5304 Control output (OUT1) changing rate limit setting for Block number 3 5400 Control output (OUT1) high limit setting for Block number 4 5401 Control output (OUT1) low limit setting for Block number 4 5402 Control output (OUT2) high limit setting for Block number 4 5403 Control output (OUT2) low limit setting for Block number 4 5404 Control output (OUT1) changing rate limit setting for Block number 4 5500 Control output (OUT1) high limit setting for Block number 5 5501 Control output (OUT1) low limit setting for Block number 5 5502 Control output (OUT2) high limit setting for Block number 5 5503 Control output (OUT2) low limit setting for Block number 5 5504 Control output (OUT1) changing rate limit setting for Block number 5 5600 Control output (OUT1) high limit setting for Block number 6 5601 Control output (OUT1) low limit setting for Block number 6 5602 Control output (OUT2) high limit setting for Block number 6 5603 Control output (OUT2) low limit setting for Block number 6 5604 Control output (OUT1) changing rate limit setting for Block number 6 5700 Control output (OUT1) high limit setting for Block number 7 5701 Control output (OUT1) low limit setting for Block number 7 5702 Control output (OUT2) high limit setting for Block number 7 5703 Control output (OUT2) low limit setting for Block number 7 5704 Control output (OUT1) changing rate limit setting for Block number 7 5800 Control output (OUT1) high limit setting for Block number 8 5801 Control output (OUT1) low limit setting for Block number 8 5802 Control output (OUT2) high limit setting for Block number 8 5803 Control output (OUT2) low limit setting for Block number 8 5804 Control output (OUT1) changing rate limit setting for Block number 8 5900 Control output (OUT1) high limit setting for Block number 9 5901 Control output (OUT1) low limit setting for Block number 9 5902 Control output (OUT2) high limit setting for Block number 9 5903 Control output (OUT2) low limit setting for Block number 9 5904 Control output (OUT1) changing rate limit setting for Block number 9 6000 Time signal output OFF time setting for Block number 0 6001 Time signal output ON time setting for Block number 0 6100 Time signal output OFF time setting for Block number 1 6101 Time signal output ON time setting for Block number 1 6200 Time signal output OFF time setting for Block number 2 6201 Time signal output ON time setting for Block number 2 6300 Time signal output OFF time setting for Block number 3 6301 Time signal output ON time setting for Block number 3 6400 Time signal output OFF time setting for Block number 4 6401 Time signal output ON time setting for Block number 4 6500 Time signal output OFF time setting for Block number 5 6501 Time signal output ON time setting for Block number 5 6600 Time signal output OFF time setting for Block number 6 6601 Time signal output ON time setting for Block number 6 6700 Time signal output OFF time setting for Block number 7 6701 Time signal output ON time setting for Block number 7 6800 Time signal output OFF time setting for Block number 8 6801 Time signal output ON time setting for Block number 8 6900 Time signal output OFF time setting for Block number 9 6901 Time signal output ON time setting for Block number 9 6A00 Time signal output OFF time setting for Block number 10 6A01 Time signal output ON time setting for Block number 10 6B00 Time signal output OFF time setting for Block number 11 6B01 Time signal output ON time setting for Block number 11 6C00 Time signal output OFF time setting for Block number 12 6C01 Time signal output ON time setting for Block number 12 6D00 Time signal output OFF time setting for Block number 13 6D01 Time signal output ON time setting for Block number 13 6E00 Time signal output OFF time setting for Block number 14 6E01 Time signal output ON time setting for Block number 14 6F00 Time signal output OFF time setting for Block number 15 6F01 Time signal output ON time setting for Block number 15 7000 Number of repeat setting for Pattern number 0 7001 Pattern link setting for Pattern number 0 and 1 7100 Number of repeat setting for Pattern number 1 7101 Pattern link setting for Pattern number 1 and 2 7200 Number of repeat setting for Pattern number 2 7201 Pattern link setting for Pattern number 2 and 3 7300 Number of repeat setting for Pattern number 3 7301 Pattern link setting for Pattern number 3 and 4 7400 Number of repeat setting for Pattern number 4 7401 Pattern link setting for Pattern number 4 and 5 7500 Number of repeat setting for Pattern number 5 7501 Pattern link setting for Pattern number 5 and 6 7600 Number of repeat setting for Pattern number 6 7601 Pattern link setting for Pattern number 6 and 7 7700 Number of repeat setting for Pattern number 7 7701 Pattern link setting for Pattern number 7 and 8 7800 Number of repeat setting for Pattern number 8 7801 Pattern link setting for Pattern number 8 and 9 7900 Number of repeat setting for Pattern number 9 7901 Pattern link setting for Pattern number 9 and 0 [SigDataEnd]