Name=Inverter J1000 MaxSigCnt=0 DataFormat=Hex [SigData] 0001 Operation signal 0002 Frequency Reference 0007 Analog output setting (10 V/4000 H) 0009 Multi-function contact output setting 000F Reference selection settings 0020 Inverter status 1 0021 Error details 1 0022 Data link status 0023 Frequency reference (U1-01) (The unit can be set by H5-13) 0024 Output frequency (U1-02) (The unit can be set by H5-13) 0025 Output voltage reference (U1-06) (Unit: 0.1V) 0026 Output current (U1-03) (Unit: 0.01A) 0029 Error details 2 002A Alarm Contents1 002B Input Terminal Status (U1-10) 002C Inverter status 2 002D Output Terminal Status (U1-11) 0031 Main circuit current voltage (U1-07)(Unit: 1V) 0034 Production code1 [ASCII], Production type(J1000 = J0) 003D Communications error details 003F Output frequency 007F Minor fault code 0098 Cumulative operation high (U4-01) 0099 Cumulative operation low (U4-01) 00AB Inverter rated current (Unit: 0.01A) 00B6 The output frequency after soft start 00B8 Frequency Reference monitor 00BF Operation error (oPE☐☐) Number 00C0 Fault Content 1 00C1 Fault Content 2 00C2 Fault Content 3 00C4 Fault Content 5 00C8 Minor fault content 2 00C9 Minor fault content 3 00CB Minor fault content 5 00D0 CPF Content 1 00D1 CPF Content 2 0900 Write parameter data to EEPROM 0101 A1-01 Access Level Selection 0103 A1-03 Initialize 0104 A1-04 Password 0105 A1-05 Password setting 0180 b1-01 Frequency Reference Selection 0181 b1-02 Run Command Selection 0182 b1-03 Stopping method selection 0183 b1-04 Reverse Operation Selection 0186 b1-07 LOCAL/REMOTE Run Selection 0187 b1-08 Run Command selection in programming modes 01C3 b1-14 Phase Order Selection 01C6 b1-17 Run Command at Power Up 018A b2-02 DC Injection Braking Current 018B b2-03 DC Injection Braking Time/DC Excitation Time at Start 018C b2-04 DC Injection Braking Time at Stop 0200 C1-01 Acceleration Time 1 0201 C1-02 Deceleration Time 1 0202 C1-03 Acceleration Time 2 0203 C1-04 Deceleration Time 2 0208 C1-09 Fast-Stop Time 020B C2-01 S-Curve Characteristic at Accel Start 020C C2-02 S-Curve Characteristic at Accel End 020D C2-03 S-Curve Characteristic at Decel Start 020E C2-04 S-Curve Characteristic at Decel Ends 020F C3-01 Slip Compensation Gain 0210 C3-02 Slip Compensation Primary Delay Time 0215 C4-01 Torque Compensation Gain 0223 C6-01 Normal/Heavy Duty Selection 0224 C6-02 Carrier Frequency Selection 0225 C6-03 Carrier Frequency Upper Limit 0226 C6-04 Carrier Frequency Lower Limit 0227 C6-05 Carrier Frequency Proportional Gain 0280 d1-01 Frequency Reference 1 0281 d1-02 Frequency Reference 2 0282 d1-03 Frequency Reference 3 0283 d1-04 Frequency Reference 4 0284 d1-05 Frequency Reference 5 0285 d1-06 Frequency Reference 6 0286 d1-07 Frequency Reference 7 0287 d1-08 Frequency Reference 8 0292 d1-17 Jog Frequency Reference 0289 d2-01 Frequency Reference Upper Limit 028A d2-02 Frequency Reference Lower Limit 0294 d3-01 Jump Frequency 1 0295 d3-02 Jump Frequency 2 0297 d3-04 Jump Frequency width 0298 d4-01 Frequency Reference Hold Function Selection 0300 E1-01 Input Voltage Setting 0302 E1-03 V/f Pattern Selection 0303 E1-04 Max Output Frequency 0304 E1-05 Max Output Voltage 0305 E1-06 Base Frequency 0306 E1-07 Mid Output Frequency 0307 E1-08 Mid Output Frequency Voltage 0308 E1-09 Minimum Output Freq. 0309 E1-10 Minimum Output Freq. Voltage 030E E2-01 Motor Rated Current 030F E2-02 Motor Rated Slip 0310 E2-03 Motor No-Load Current 0312 E2-05 Motor Line-to-Line Resistance 0438 H1-01 Multi-Function Digital Input Terminal S1 Function Selection 0439 H1-02 Multi-Function Digital Input Terminal S2 Function Selection 0400 H1-03 Multi-Function Digital Input Terminal S3 Function Selection 0401 H1-04 Multi-Function Digital Input Terminal S4 Function Selection 0402 H1-05 Multi-Function Digital Input Terminal S5 Function Selection 040B H2-01 Terminal MA, MB and MC Function Selection (relay) 0410 H3-01 Terminal A1 Signal Level Selection 0411 H3-03 Terminal A1 Gain Setting 0412 H3-04 Terminal A1 Bias Setting 041B H3-13 Analog Input Filter Time Constant 041D H4-01 Multi-Function Analog Output Terminal AM 041E H4-02 Multi-Function Analog Output Terminal AM Gain 041F H4-03 Multi-Function Analog Output Terminal AM Bias 0425 H5-01 Slave Address 0426 H5-02 Communication Speed Selection 0427 H5-03 Communication Parity Selection 0428 H5-04 Stopping Method After Communication Error 0429 H5-05 Communication Fault Detection Selection 042A H5-06 Drive Transmit Wait Time 042B H5-07 RTS Control Selection 043D H5-12 Run Command Method Selection 043E H5-13 MEMOBUS Freq. Reference and Freq. Monitor Unit 0480 L1-01 Motor Overload Protection Selection 0481 L1-02 Motor Overload Protection Time 046D L1-13 Continuous Electrothermal Operation Selection 0485 L2-01 Momentary Power Loss Operation Selection 048F L3-01 Stall Prevention Selection during Acceleration 0490 L3-02 Stall Prevention Level during Acceleration 0492 L3-04 Stall Prevention Selection during Deceleration 0493 L3-05 Stall Prevention Selection during Run 0494 L3-06 Stall Prevention Level during Run 0499 L4-01 Speed Agreement Detection Level 0470 L4-07 Frequency Detection Conditions 049E L5-01 Number of Auto Restart Attempts 04A1 L6-01 Torque Detection Selection 04A2 L6-02 Torque Detection Level 04A3 L6-03 Torque Detection Time 04AD L8-01 Internal Dynamic Braking Resistor Protection Selection (ERF type) 04B1 L8-05 Input Phase Loss Protection Selection 04B6 L8-10 Heatsink Cooling Fan Operation Selection 04B8 L8-12 Ambient Temperature Setting 04BE L8-18 Soft CLA Selection 04EC L8-35 Installation Method Selection 04EF L8-38 Carrier Frequency Reduction 0581 n1-02 Hunting Prevention Gain Setting 0531 n3-13 Overexcitation Deceleration Gain 0501 o1-02 User Monitor Selection After Power Up 0502 o1-03 Digital Operator Display Selection 0506 o2-02 STOP Key Function Selection 0508 o2-04 Drive Model Selection 0509 o2-05 Frequency Reference Setting Method Selection 050A o2-06 LED Operation Selection when Digital Operator is Disconnected 050D o2-09 Initialization mode 0515 o3-01 COPY function key 0516 o3-02 READ permission selection 050B o4-01 Accumulated Operation Time Setting 050C o4-02 Accumulated Operation Time Selection 050E o4-03 Cooling Fan Operation Time Setting 051D o4-05 Capacitor Maintenance Setting 0523 o4-07 Inrush Prevention Relay Maintenance Setting 0525 o4-09 IGBT Maintenance Setting 0510 o4-11 U2 Initialize Selection 0040 U1-01 Frequency Reference 0041 U1-02 Output Frequency 0042 U1-03 Output Current 0045 U1-06 Output Voltage Reference 0046 U1-07 DC Bus Voltage 0049 U1-10 Input Terminal Status 004A U1-11 Output Terminal Status 004E U1-13 Analog Input Terminal A1 Input monitor 0066 U1-19 MEMOBUS communication Error Code 004D U1-25 Software No.(ROM) 005B U1-26 Software No.(FLASH) 0080 U2-01 Current Fault 0081 U2-02 Previous Fault 004C U4-01 Accumulated Operation Time 007E U4-04 Cooling Fan Maintenance 007C U4-05 Capacitor Maintenance 07D6 U4-06 Soft Charge Bypass Relay Maintenance 07D7 U4-07 IGBT Maintenance 0068 U4-08 Heatsink Temperature 005E U4-09 LED Check 07CF U4-13 Peak Hold Current [SigDataEnd] [SigData]-B 0001.0 H5-12 = 0: Forward Run Command (0 = Stop, 1 = Run) H5-12 = 1: Run Command (0 = Stop, 1 = Forward Run) 0001.1 H5-12 = 0: Reverse Run Command (0 = Stop, 1 = Run) H5-12 = 1: Forward/Reverse (0 = Stop, 1 = Reverse Run) 0001.2 External fault 1: Error (EFO) 0001.3 Fault reset 1: Reset command 0001.4 Multi-function input command 1 0001.5 Multi-function input command 2 0001.6 Multi-function input command 3 0001.7 Multi-function input command 4 0001.8 Multi-function input command 5 0002 Frequency Reference 0007 Analog output setting (10 V/4000 H) 0009.0 Contact output (Terminal MA/MB-MC) 1: ON 0: OFF 000F.C Broadcast data terminal S5 input 1: Enabled 0: Disabled 0020.0 Operation 1: Operating 0: Stopped 0020.1 Reverse operation 1: Reverse operation 0: Forward operation 0020.2 Inverter startup complete 1: Completed 2: Not completed 0020.3 Error 1: Error 0020.4 Data setting error 1: Error 0020.5 Multi-function contact output (Terminal MA/MB-MC) 1: ON 0: OFF 0020.E ComRef status 0020.F ComCtrl status 0021.0 Overcurrent (oC) 0021.1 Main control circuit overvoltage (ov) 0021.2 Inverter overload (ol2) 0021.3 Inverter overheat (oH1) 0021.4 Braking Resistor Fault(rH) 0021.7 External Fault(EF0~5) 0021.8 Hardware Fault (includes OFx) 0021.9 Motor overload (oL1), Overtorque detection (oL3) 0021.B Main circuit undervoltage (Uv) detected 0021.C DC Bus Undervoltage(Uv1), Inrush Prevention Circuit Fault(Uv3) 0021.D Main Circuit Voltage Fault (PF), Output Open-phase (LF) 0021.E EMOBUS communications error(CE) 0021.F Operator disconnected (oPr) 0022.0 1: Writing data 0022.3 1: Upper and lower limit errors 0022.4 1: Data integrity error 0022.5 1: EEPROM Writing data 0023 Frequency reference (U1-01) (The unit can be set by H5-13) 0024 Output frequency (U1-02) (The unit can be set by H5-13) 0025 Output voltage reference (U1-06) (Unit: 0.1V) 0026 Output current (U1-03) (Unit: 0.01A) 0029.2 DC Bus Voltage Fault(PF) 0029.3 Output Open-phase (LF) 0029.4 Braking Resistor Fault(rH) 002A.2 EF: Simultaneous Forward and Reverse Run Commands 002A.3 bb: Drive Baseblock 002A.4 oL3: Overtorque 1 002A.5 oH: Heatsink Overheat 002A.6 oV: DC Bus Overvoltage 002A.7 Uv: DC Bus Undervoltage 002A.9 CE: Communications Error 002B.0 1: Control circuit terminal S1 Closed 002B.1 1: Control circuit terminal S2 Closed 002B.2 1: Control circuit terminal S3 Closed 002B.3 1: Control circuit terminal S4 Closed 002B.4 1: Control circuit terminal S5 Closed 002C.0 Operation 1: Operating 002C.1 Zero-speed 1: Zero-speed 002C.2 Frequency matching 1: Matched 002C.3 User-defined speed matching 1: Matched 002C.4 Frequency detection 1 1: Output frequency≦L4-01 002C.5 Frequency detection 2 1: Output frequency≧L4-01 002C.6 Inverter startup completed 1: Startup completed 002C.7 Low voltage detection 1: Detected 002C.8 Baseblock 1: Inverter output baseblock 002C.9 Frequency reference mode 1: Not communications 0: Communications 002C.A Run Command mode 1: Not communications 0: Communications 002C.B Overtorque detection 002C.E Error 1:Error occurred 002C.F MEMOBUS communications time-out 1: Timed out 002D.0 Multi-function contact output (terminal MA/MB-MC) 1: ON 0: OFF 0031 Main circuit current voltage (U1-07)(Unit: 1V) 0034 Production code1 [ASCII], Production type(J1000 = J0) 003D.0 CRC error 003D.1 Invalid data length 003D.3 Parity error 003D.4 Overrun error 003D.5 Framing error 003D.6 Time-out 003F Output frequency 007F Minor fault code 0098 Cumulative operation high (U4-01) 0099 Cumulative operation low (U4-01) 00AB Inverter rated current (Unit: 0.01A) 00B6 The output frequency after soft start 00B8 Frequency Reference monitor 00BF Operation error (oPE☐☐) Number 00C0.1 DC Bus Undervoltage(Uv1) 00C0.3 Inrush Prevention Circuit Fault(Uv3) 00C0.6 Overcurrent (oC) 00C0.7 Main control circuit overvoltage (ov) 00C0.9 Heat sink overheating (oH1) 00C0.A Motor overload (oL1) 00C0.B Inverter overload (oL2) 00C0.C Overtorque detection (oL3) 00C0.F Braking Resistor Fault(rH) 00C1.0 External fault(Input Terminal S3) (EF3) 00C1.1 External fault(Input Terminal S4) (EF4) 00C1.2 External fault(Input Terminal S5) (EF5) 00C1.A Main circuit voltage fault(PF) 00C1.D Operator disconnected (oPr) 00C1.E EEPROM Writing data error (Err) 00C2.0 MEMOBUS communication error (CE) 00C2.6 External fault detected in MEMOBUS communication option unit (EF0) 00C2.F Hardware error (Err) 00C4.1 External fault(Input Terminal S1) (EF1) 00C4.2 External fault(Input Terminal S2) (EF2) 00C4.5 Current offset fault(CoF) 00C8.0 Main circuit undervoltage(Uv) 00C8.1 Main circuit overvoltage(Ov) 00C8.2 Heat sink overheating (oH) 00C8.4 Overtorque (oL3) 00C8.6 Input Forward and Reverse command at same time 00C8.7 Inverter base block (bb) 00C8.8 External fault(Input Terminal S3) (EF3) 00C8.9 External fault(Input Terminal S4) (EF4) 00C8.A External fault(Input Terminal S5) (EF5) 00C9.2 Operator disconnected (oPr) 00C9.3 MEMOBUS communication error (CE) 00C9.5 Communication standby 00C9.6 Motor overload (oL1) 00C9.7 Inverter overload (oL2) 00CB.8 External fault(Input Terminal S1) (EF1) 00CB.9 External fault(Input Terminal S2) (EF2) 00D0.2 A/D converter fault (CPF02) 00D0.6 EEPROM data fault (CPF06) 00D0.8 EEPROM serial communications fault (CPF08) 00D0.B RAM fault (CPF11) 00D0.C Flash memory fault (CPF12) 00D0.E The control circuit fault (CPF14) 00D1.1 Interrupt fault (CPF17) 00D1.2 The control circuit fault (CPF18) 00D1.6 A/D converter fault(CPF22) 00D1.7 PWM feedback data fault (CPF23) 00D1.8 Inverte capacity signal fault(CPF24) 0900 Write parameter data to EEPROM 0101 A1-01 Access Level Selection 0103 A1-03 Initialize 0104 A1-04 Password 0105 A1-05 Password setting 0180 b1-01 Frequency Reference Selection 0181 b1-02 Run Command Selection 0182 b1-03 Stopping method selection 0183 b1-04 Reverse Operation Selection 0186 b1-07 LOCAL/REMOTE Run Selection 0187 b1-08 Run Command selection in programming modes 01C3 b1-14 Phase Order Selection 01C6 b1-17 Run Command at Power Up 018A b2-02 DC Injection Braking Current 018B b2-03 DC Injection Braking Time/DC Excitation Time at Start 018C b2-04 DC Injection Braking Time at Stop 0200 C1-01 Acceleration Time 1 0201 C1-02 Deceleration Time 1 0202 C1-03 Acceleration Time 2 0203 C1-04 Deceleration Time 2 0208 C1-09 Fast-Stop Time 020B C2-01 S-Curve Characteristic at Accel Start 020C C2-02 S-Curve Characteristic at Accel End 020D C2-03 S-Curve Characteristic at Decel Start 020E C2-04 S-Curve Characteristic at Decel Ends 020F C3-01 Slip Compensation Gain 0210 C3-02 Slip Compensation Primary Delay Time 0215 C4-01 Torque Compensation Gain 0223 C6-01 Normal/Heavy Duty Selection 0224 C6-02 Carrier Frequency Selection 0225 C6-03 Carrier Frequency Upper Limit 0226 C6-04 Carrier Frequency Lower Limit 0227 C6-05 Carrier Frequency Proportional Gain 0280 d1-01 Frequency Reference 1 0281 d1-02 Frequency Reference 2 0282 d1-03 Frequency Reference 3 0283 d1-04 Frequency Reference 4 0284 d1-05 Frequency Reference 5 0285 d1-06 Frequency Reference 6 0286 d1-07 Frequency Reference 7 0287 d1-08 Frequency Reference 8 0292 d1-17 Jog Frequency Reference 0289 d2-01 Frequency Reference Upper Limit 028A d2-02 Frequency Reference Lower Limit 0294 d3-01 Jump Frequency 1 0295 d3-02 Jump Frequency 2 0297 d3-04 Jump Frequency width 0298 d4-01 Frequency Reference Hold Function Selection 0300 E1-01 Input Voltage Setting 0302 E1-03 V/f Pattern Selection 0303 E1-04 Max Output Frequency 0304 E1-05 Max Output Voltage 0305 E1-06 Base Frequency 0306 E1-07 Mid Output Frequency 0307 E1-08 Mid Output Frequency Voltage 0308 E1-09 Minimum Output Freq. 0309 E1-10 Minimum Output Freq. Voltage 030E E2-01 Motor Rated Current 030F E2-02 Motor Rated Slip 0310 E2-03 Motor No-Load Current 0312 E2-05 Motor Line-to-Line Resistance 0438 H1-01 Multi-Function Digital Input Terminal S1 Function Selection 0439 H1-02 Multi-Function Digital Input Terminal S2 Function Selection 0400 H1-03 Multi-Function Digital Input Terminal S3 Function Selection 0401 H1-04 Multi-Function Digital Input Terminal S4 Function Selection 0402 H1-05 Multi-Function Digital Input Terminal S5 Function Selection 040B H2-01 Terminal MA, MB and MC Function Selection (relay) 0410 H3-01 Terminal A1 Signal Level Selection 0411 H3-03 Terminal A1 Gain Setting 0412 H3-04 Terminal A1 Bias Setting 041B H3-13 Analog Input Filter Time Constant 041D H4-01 Multi-Function Analog Output Terminal AM 041E H4-02 Multi-Function Analog Output Terminal AM Gain 041F H4-03 Multi-Function Analog Output Terminal AM Bias 0425 H5-01 Slave Address 0426 H5-02 Communication Speed Selection 0427 H5-03 Communication Parity Selection 0428 H5-04 Stopping Method After Communication Error 0429 H5-05 Communication Fault Detection Selection 042A H5-06 Drive Transmit Wait Time 042B H5-07 RTS Control Selection 043D H5-12 Run Command Method Selection 043E H5-13 MEMOBUS Freq. Reference and Freq. Monitor Unit 0480 L1-01 Motor Overload Protection Selection 0481 L1-02 Motor Overload Protection Time 046D L1-13 Continuous Electrothermal Operation Selection 0485 L2-01 Momentary Power Loss Operation Selection 048F L3-01 Stall Prevention Selection during Acceleration 0490 L3-02 Stall Prevention Level during Acceleration 0492 L3-04 Stall Prevention Selection during Deceleration 0493 L3-05 Stall Prevention Selection during Run 0494 L3-06 Stall Prevention Level during Run 0499 L4-01 Speed Agreement Detection Level 0470 L4-07 Frequency Detection Conditions 049E L5-01 Number of Auto Restart Attempts 04A1 L6-01 Torque Detection Selection 04A2 L6-02 Torque Detection Level 04A3 L6-03 Torque Detection Time 04AD L8-01 Internal Dynamic Braking Resistor Protection Selection (ERF type) 04B1 L8-05 Input Phase Loss Protection Selection 04B6 L8-10 Heatsink Cooling Fan Operation Selection 04B8 L8-12 Ambient Temperature Setting 04BE L8-18 Soft CLA Selection 04EC L8-35 Installation Method Selection 04EF L8-38 Carrier Frequency Reduction 0581 n1-02 Hunting Prevention Gain Setting 0531 n3-13 Overexcitation Deceleration Gain 0501 o1-02 User Monitor Selection After Power Up 0502 o1-03 Digital Operator Display Selection 0506 o2-02 STOP Key Function Selection 0508 o2-04 Drive Model Selection 0509 o2-05 Frequency Reference Setting Method Selection 050A o2-06 LED Operation Selection when Digital Operator is Disconnected 050D o2-09 Initialization mode 0515 o3-01 COPY function key 0516 o3-02 READ permission selection 050B o4-01 Accumulated Operation Time Setting 050C o4-02 Accumulated Operation Time Selection 050E o4-03 Cooling Fan Operation Time Setting 051D o4-05 Capacitor Maintenance Setting 0523 o4-07 Inrush Prevention Relay Maintenance Setting 0525 o4-09 IGBT Maintenance Setting 0510 o4-11 U2 Initialize Selection 0040 U1-01 Frequency Reference 0041 U1-02 Output Frequency 0042 U1-03 Output Current 0045 U1-06 Output Voltage Reference 0046 U1-07 DC Bus Voltage 0049.0 U1-10 1: Digital input terminal S1 enabled 0049.1 U1-10 1: Digital input terminal S2 enabled 0049.2 U1-10 1: Digital input terminal S3 enabled 0049.3 U1-10 1: Digital input terminal S4 enabled 0049.4 U1-10 1: Digital input terminal S5 enabled 004A.0 U1-11 1: Multi-Function Digital Output (fault) (terminal MA/MB-MC) 004E U1-13 Analog Input Terminal A1 Input monitor 0066.0 U1-19 1:CRC error 0066.1 U1-19 1:Data length error 0066.3 U1-19 1:Parity error 0066.4 U1-19 1:Overrun error 0066.5 U1-19 1:Framing error 0066.6 U1-19 1:Timeout 004D U1-25 Software No.(ROM) 005B U1-26 Software No.(FLASH) 0080 U2-01 Current Fault 0081 U2-02 Previous Fault 004C U4-01 Accumulated Operation Time 007E U4-04 Cooling Fan Maintenance 007C U4-05 Capacitor Maintenance 07D6 U4-06 Soft Charge Bypass Relay Maintenance 07D7 U4-07 IGBT Maintenance 0068 U4-08 Heatsink Temperature 005E U4-09 LED Check 07CF U4-13 Peak Hold Current [SigDataEnd]-B