Name=Inverter VS mini J7 MaxSigCnt=0 DataFormat=Hex [SigData] 0001 Operation signal 0002 Frequency reference 0003 V/f gain (1000/100%), Setting range:2.0 to 200.0% 0020 Status Signal 0021 Fault Contents 0022 Data link status 0023 Frequency reference 0024 Output frequency 0027 Output current (10/1A) 0028 Output voltage reference (1/1V) 002B Control Circuit Terminal Input Status 002C Inverter status 002D Control Circuit Terminal Output Status 0031 Main circuit DC voltage (1/1V) 003D Contents of Communication Error 0900 ENTER command 0101 n01 Password 0102 n02 RUN Command Selection 0103 n03 Frequency Reference Selection 0104 n04 Stopping Method Selection 0105 n05 Reverse Run Prohibit 0106 n06 Stop Key Selection 0107 n07 Frequency Reference Selection in Local Mode 0108 n08 Frequency Reference Setting Method From Digital Operator 0109 n09 Max. Output Frequency 010A n10 Max. Voltage 010B n11 Max. Voltage Output Frequency 010C n12 Mid. Output Frequency 010D n13 Mid. Output Frequency Voltage 010E n14 Min. Output Frequency 010F n15 Min. Output Frequency Voltage 0110 n16 Acceleration Time 1 0111 n17 Deceleration Time 1 0112 n18 Acceleration Time 2 0113 n19 Deceleration Time 2 0114 n20 S-curve Selection 0115 n21 Frequency Reference 1 (Master Speed Frequency Reference) 0116 n22 Frequency Reference 2 0117 n23 Frequency Reference 3 0118 n24 Frequency Reference 4 0119 n25 Frequency Reference 5 011A n26 Frequency Reference 6 011B n27 Frequency Reference 7 011C n28 Frequency Reference 8 011D n29 Jog Frequency 011E n30 Frequency Reference Upper Limit 011F n31 Frequency Reference Lower Limit 0120 n32 Motor Rated Current 0121 n33 Electronic Thermal Motor Protection Selection 0122 n34 Electronic Thermal Motor Protection Time Constant Setting 0123 n35 Selecting Cooling Fan Operation 0124 n36 Multi-function Input Selection 2 0125 n37 Multi-function Input Selection 3 0126 n38 Multi-function Input Selection 4 0127 n39 Multi-function Input Selection 5 0128 n40 Multi-function Output Selection 0129 n41 Analog Frequency Reference Gain 012A n42 Analog Frequency Reference Bias 012B n43 Analog Frequency Reference Filter Time Constant 012C n44 Multi-function Ana-log Output(terminal AM-AC) 012D n45 Analog Monitor Gain 012E n46 Carrier Frequency Selection 012F n47 Momentary Power Loss Ridethrough Method 0130 n48 Automatic Retry Attempts 0131 n49 Jump Frequency 1 0132 n50 Jump Frequency 2 0133 n51 Jump Frequency Range 0134 n52 DC Injection Braking Current 0135 n53 DC Injection Braking Time at Stop 0136 n54 DC Injection Braking Time at Startup 0137 n55 Stall Prevention During Deceleration 0138 n56 Stall Prevention Level During Acceleration 0139 n57 Stall Prevention while Running 013A n58 Frequency Detection Level 013B n59 Overtorque Detection Function 013C n60 Overtorque Detection Level 013D n61 Overtorque Detection Time 013E n62 Hold Output 013F n63 Torque Compensation Gain 0140 n64 Motor Rated Slip 0141 n65 Motor No-load Current 0142 n66 Slip Compensation Gain 0143 n67 Slip Compensation Time Constant 0144 n68 MEMOBUS Timeover Detection Selection 0145 n69 MEMOBUS frequency reference and frequency monitor unit 0146 n70 MEMOBUS Slave Address 0147 n71 MEMOBUS BPS Selection 0148 n72 MEMOBUS Parity Selection 0149 n73 Transmission Waiting Time 014A n74 RTS Control 014B n75 Reducing Carrier Frequency Selection At Low Speed 014C n76 Constant Copy Function Selection 014D n77 Constant Read Selection Prohibit 014E n78 Fault History 014F n79 Software Version No. [SigDataEnd] [SigData]-B 0001.0 Run command 1: Run 0: Stop 0001.1 Reverse run 1: Reverse run 0: Forward run 0001.2 External fault 1: Error (EFO) 0001.3 Fault reset 1: Reset command 0001.5 Multi-function input reference 2 (Function selected by n36) 0001.6 Multi-function input reference 3 (Function selected by n37) 0001.7 Multi-function input reference 4 (Function selected by n38) 0001.8 Multi-function input reference 5 (Function selected by n39) 0002 Frequency reference 0003 V/f gain (1000/100%), Setting range:2.0 to 200.0% 0009.0 Multi-function output reference 1 1: MA "ON" (Effective when n040=18) 0020.0 Run command 1: Run 0: Stop 0020.1 Reverse run 1: Reverse run 0: Forward run 0020.2 Inverter operation ready 1: Ready 0: Not ready 0020.3 Fault 1: Fault 0020.4 Data setting error 1:Error 0020.5 Multi-function output 1 (1: MA ON) 0021.0 Overcurrent (OC) 0021.1 Overvoltage (OV) 0021.2 Inverter overload (OL2) 0021.3 Inverter overheat (OH1) 0021.7 External fault (EF, EFO),Emergence stop (STP) 0021.8 Hardware fault (FXX) 0021.9 Motor overload (OL1) 0021.A Overtorque detection (OL3) 0021.C Power loss (UV1) 0021.D Grounding (GF) 0021.E MEMOBUS communications timeover (CE) 0022.0 Data write in 0022.3 Upper/lower limit fault 0022.4 Consistency fault 0023 Frequency reference 0024 Output frequency 0027 Output current (10/1A) 0028 Output voltage reference (1/1V) 002B.0 Terminal S1 1: Closed 002B.1 Terminal S2 1: Closed 002B.2 Terminal S3 1: Closed 002B.3 Terminal S4 1: Closed 002B.4 Terminal S5 1: Closed 002C.0 Run 1:Run 002C.1 Zero-speed 1: Zero-speed 002C.2 Frequency agreed 1: Agreed 002C.3 Minor fault (Alarm is indicated.) 002C.4 Frequency detection 1 1: Output frequency ≤ (n58) 002C.5 Frequency detection 2 1: Output frequency ≥ (n58) 002C.6 Inverter operation ready 1:Ready 002C.7 Undervoltage detection 1: Undervoltage detection 002C.8 Baseblock 1: Inverter baseblock detection 002C.9 Frequency reference mode 1: Other than communications 0: Communications 002C.A Run Command mode 1: Other than communications 0: Communications 002C.B Overtorque detection 1: Overtorque detection 002C.D Fault restart 002C.E Fault (Including communications timeover) 1: Fault 002C.F Communications timeover 1: Timeover 002D.0 MA "ON" 1: Closed 0031 Main circuit DC voltage (1/1V) 003D.0 CRC error 003D.1 Improper data length 003D.3 Parity error 003D.4 Overrun error 003D.5 Framing error 003D.6 Timeover 0900 ENTER command 0101 n01 Password 0102 n02 RUN Command Selection 0103 n03 Frequency Reference Selection 0104 n04 Stopping Method Selection 0105 n05 Reverse Run Prohibit 0106 n06 Stop Key Selection 0107 n07 Frequency Reference Selection in Local Mode 0108 n08 Frequency Reference Setting Method From Digital Operator 0109 n09 Max. Output Frequency 010A n10 Max. Voltage 010B n11 Max. Voltage Output Frequency 010C n12 Mid. Output Frequency 010D n13 Mid. Output Frequency Voltage 010E n14 Min. Output Frequency 010F n15 Min. Output Frequency Voltage 0110 n16 Acceleration Time 1 0111 n17 Deceleration Time 1 0112 n18 Acceleration Time 2 0113 n19 Deceleration Time 2 0114 n20 S-curve Selection 0115 n21 Frequency Reference 1 (Master Speed Frequency Reference) 0116 n22 Frequency Reference 2 0117 n23 Frequency Reference 3 0118 n24 Frequency Reference 4 0119 n25 Frequency Reference 5 011A n26 Frequency Reference 6 011B n27 Frequency Reference 7 011C n28 Frequency Reference 8 011D n29 Jog Frequency 011E n30 Frequency Reference Upper Limit 011F n31 Frequency Reference Lower Limit 0120 n32 Motor Rated Current 0121 n33 Electronic Thermal Motor Protection Selection 0122 n34 Electronic Thermal Motor Protection Time Constant Setting 0123 n35 Selecting Cooling Fan Operation 0124 n36 Multi-function Input Selection 2 0125 n37 Multi-function Input Selection 3 0126 n38 Multi-function Input Selection 4 0127 n39 Multi-function Input Selection 5 0128 n40 Multi-function Output Selection 0129 n41 Analog Frequency Reference Gain 012A n42 Analog Frequency Reference Bias 012B n43 Analog Frequency Reference Filter Time Constant 012C n44 Multi-function Ana-log Output(terminal AM-AC) 012D n45 Analog Monitor Gain 012E n46 Carrier Frequency Selection 012F n47 Momentary Power Loss Ridethrough Method 0130 n48 Automatic Retry Attempts 0131 n49 Jump Frequency 1 0132 n50 Jump Frequency 2 0133 n51 Jump Frequency Range 0134 n52 DC Injection Braking Current 0135 n53 DC Injection Braking Time at Stop 0136 n54 DC Injection Braking Time at Startup 0137 n55 Stall Prevention During Deceleration 0138 n56 Stall Prevention Level During Acceleration 0139 n57 Stall Prevention while Running 013A n58 Frequency Detection Level 013B n59 Overtorque Detection Function 013C n60 Overtorque Detection Level 013D n61 Overtorque Detection Time 013E n62 Hold Output 013F n63 Torque Compensation Gain 0140 n64 Motor Rated Slip 0141 n65 Motor No-load Current 0142 n66 Slip Compensation Gain 0143 n67 Slip Compensation Time Constant 0144 n68 MEMOBUS Timeover Detection Selection 0145 n69 MEMOBUS frequency reference and frequency monitor unit 0146 n70 MEMOBUS Slave Address 0147 n71 MEMOBUS BPS Selection 0148 n72 MEMOBUS Parity Selection 0149 n73 Transmission Waiting Time 014A n74 RTS Control 014B n75 Reducing Carrier Frequency Selection At Low Speed 014C n76 Constant Copy Function Selection 014D n77 Constant Read Selection Prohibit 014E n78 Fault History 014F n79 Software Version No. [SigDataEnd]-B