Name=Inverter Varispeed L7 MaxSigCnt=0 DataFormat=Hex [SigData] 0001 Frequency reference 0002 Frequency reference (Set units using constant o1-03) 0007 Analog output 1 setting (-11 V/-1540 to 11 V/1540) 0008 Analog output 2 setting (-11 V/-1540 to 11 V/1540) 0009 Multi-function contact output setting 000F Reference selection settings 0020 Inverter status 0021 Error details 0022 Data link status 0023 Frequency reference (U1-01) 0024 Output frequency (U1-02) 0025 Output voltage reference (U1-06) 0026 Output current (U1-03) (Unit: 1/0.1A) 0027 Output power (U1-08) 0028 Torque reference (U1-09) 002B Sequence input status 002C Inverter status 002D Multi-function contact output status 0031 Main circuit DC voltage 0032 Torque monitor (Unit: 1/0.1%) 0033 Output power (U1-08) 003B CPU software number 003C Flash software number 003D Communications error details 003E kVA setting 003F Control method 0900 Write constant data to EEPROM 0910 Constant data is not written to EEPROM, but refreshed in RAM only. 0100 A1-00 Language selection for Digital Operator display 0101 A1-01 Constant access level 0102 A1-02 Control method selection 0103 A1-03 Initialize 0104 A1-04 Password 0105 A1-05 Password setting 0106 A2-01 User specified parameters 0107 A2-02 User specified parameters 0108 A2-03 User specified parameters 0109 A2-04 User specified parameters 010A A2-05 User specified parameters 010B A2-06 User specified parameters 010C A2-07 User specified parameters 010D A2-08 User specified parameters 010E A2-09 User specified parameters 010F A2-10 User specified parameters 0110 A2-11 User specified parameters 0111 A2-12 User specified parameters 0112 A2-13 User specified parameters 0113 A2-14 User specified parameters 0114 A2-15 User specified parameters 0115 A2-16 User specified parameters 0116 A2-17 User specified parameters 0117 A2-18 User specified parameters 0118 A2-19 User specified parameters 0119 A2-20 User specified parameters 011A A2-21 User specified parameters 011B A2-22 User specified parameters 011C A2-23 User specified parameters 011D A2-24 User specified parameters 011E A2-25 User specified parameters 011F A2-26 User specified parameters 0120 A2-27 User specified parameters 0121 A2-28 User specified parameters 0122 A2-29 User specified parameters 0123 A2-30 User specified parameters 0124 A2-31 User specified parameters 0125 A2-32 User specified parameters 0180 b1-01 Reference rource selection 0181 b1-02 Run Command source selection 0182 b1-03 Stopping method selection 0185 b1-06 Control input scan 0186 b1-07 Operation selection after switching to remote mode 0187 b1-08 Run Command selection in programming modes 0190 b2-08 Magnetic flux compensation volume 01A3 b4-01 Timer function ON-delay time 01A4 b4-02 Timer function OFF-delay time 01B6 b6-01 Dwell frequency at start 01B7 b6-02 Dwell time at start 01B8 b6-03 Dwell frequency at stop 01B9 b6-04 Dwell time at stop 01CA b7-01 Droop control gain 01CB b7-02 Droop control delay time 01CC b8-01 Energy-saving mode selection 01F8 b8-16 Energy savings control parameter Ki 01F9 b8-17 Energy savings control parameter Kt 0200 C1-01 Acceleration time 1 0201 C1-02 Deceleration time 1 0202 C1-03 Acceleration time 2 0203 C1-04 Deceleration time 2 0204 C1-05 Acceleration time 3 0205 C1-06 Deceleration time 3 0206 C1-07 Acceleration time 4 0207 C1-08 Deceleration time 4 0208 C1-09 Fast stop time 0209 C1-10 Accel/decel time setting unit 020A C1-11 Accel/decel time switching frequency 020B C2-01 S-curve characteristic time at acceleration start 020C C2-02 S-curve characteristic time at acceleration end 020D C2-03 S-curve characteristic time at deceleration start 020E C2-04 S-curve characteristic time at deceleration end 0232 C2-05 S character characteristic time below leveling speed 020F C3-01 Slip compensation gain 0210 C3-02 Slip compensation primary delay time 0211 C3-03 Slip compensation limit 0212 C3-04 Slip compensation selection during regeneration 0213 C3-05 Output voltage limit operation selection 0215 C4-01 Torque compensation gain 0216 C4-02 Torque compensation delay time parameter 0217 C4-03 Starting torque compensation (FWD) 0218 C4-04 Starting torque compensation (REV) 0219 C4-05 Starting torque compensation time parameter 021A C4-06 Torque compensation primary delay time 2 021B C5-01 ASR proportional (P) gain 1 021C C5-02 ASR integral (I) time 1 021D C5-03 ASR proportional (P) gain 2 021E C5-04 ASR integral (I) time 2 0220 C5-06 ASR primary delay time 0221 C5-07 ASR switching frequency 0222 C5-08 ASR integral (I) limit 022E C5-09 ASR proportional (P) gain 3 0231 C5-10 ASR integral (I) time 3 0238 C5-15 ASR gain for encoder offset tuning 0224 C6-02 Carrier frequency selection 0225 C6-03 Carrier frequency upper limit 022B C6-09 Carrier during rotational autotuning 022C C6-10 Carrier during stationary autotuning 022D C6-11 Carrier frequency selection 2 0280 d1-01 Frequency reference 1 0281 d1-02 Frequency reference 2 0282 d1-03 Frequency reference 3 0283 d1-04 Frequency reference 4 0284 d1-05 Frequency reference 5 0285 d1-06 Frequency reference 6 0286 d1-07 Frequency reference 7 0287 d1-08 Frequency reference 8 0288 d1-09 Nominal speed reference 028B d1-10 Intermediate speed 1 reference 028C d1-11 Intermediate speed 2 reference 028D d1-12 Intermediate speed 3 reference 028E d1-13 Releveling speed reference 028F d1-14 Inspection speed reference 0292 d1-17 Leveling speed reference 02A7 d1-18 Speed priority selection 02A2 d6-03 Field forcing function selection 02A5 d6-06 Field forcing limit value 0300 E1-01 Input voltage setting 0302 E1-03 V/f pattern selection 0303 E1-04 Max. output frequency (FMAX) 0304 E1-05 Max. output voltage (VMAX) 0305 E1-06 Base frequency (FA) 0306 E1-07 Mid. output frequency (FB) 0307 E1-08 Mid. Output frequency voltage (VB) 0308 E1-09 Min. output frequency (FMIN) 0309 E1-10 Min. output frequency voltage (VMIN) 030C E1-13 Base voltage (VBASE) 030E E2-01 Motor rated current 030F E2-02 Motor rated slip 0310 E2-03 Motor noload current 0311 E2-04 Number of motor poles 0312 E2-05 Motor line-to-line resistance 0313 E2-06 Motor leak inductance 0314 E2-07 Motor iron saturation coefficient 1 0315 E2-08 Motor iron saturation coefficient 2 0316 E2-09 Motor mechanical loss 0317 E2-10 Motor iron loss for torque compensation 0318 E2-11 Motor rated output power 0328 E2-12 Motor iron saturation coefficient 3 032A E5-02 Motor rated power 032B E5-03 Motor rated current 032C E5-04 Number of motor poles 032D E5-05 Motor line-to-line resistance 032E E5-06 d-axis inductance 032F E5-07 q-axis inductance 0331 E5-09 Motor voltage parameter 0333 E5-11 PG home position offset 0380 F1-01 PG constant 0381 F1-02 Operation selection at PG open circuit (PGO) 0382 F1-03 Operation selection at overspeed (OS) 0383 F1-04 Operation selection at deviation 0384 F1-05 PG rotation 0385 F1-06 PG division rate (PG pulse monitor) 0387 F1-08 Overspeed detection level 0388 F1-09 Overspeed detection delay time 0389 F1-10 Excessive speed deviation detection level 038A F1-11 Excessive speed deviation detection delay time 038D F1-14 PG open-circuit detection time 03AD F1-18 DV3 fault detection selection 03AE F1-19 DV4 fault detection selection 03B0 F1-21 Absolute encoder resolution 03B1 F1-22 Magnet position offset 03B4 F1-25 Encoder copy selection 03B5 F1-26 Encoder copy write permission selection 0391 F4-01 Channel 1 monitor selection 0392 F4-02 Channel 1 gain 0393 F4-03 Channel 2 monitor selection 0394 F4-04 Channel 2 gain 0395 F4-05 Channel 1 output monitor bias 0396 F4-06 Channel 2 output monitor bias 0397 F4-07 Analog output signal level for channel 1 0398 F4-08 Analog output signal level for channel 2 0399 F5-01 Channel 1 output selection 039A F5-02 Channel 2 output selection 039B F5-03 Channel 3 output selection 039C F5-04 Channel 4 output selection 039D F5-05 Channel 5 output selection 039E F5-06 Channel 6 output selection 039F F5-07 Channel 7 output selection 03A0 F5-08 Channel 8 output selection 03A1 F5-09 DO-08 output mode selection 03A2 F6-01 Operation selection after communications error 03A3 F6-02 Input level of external fault from communications option card 03A4 F6-03 Stopping method for external fault from communications option card 03A5 F6-04 Trace sampling from communications option card 03A6 F6-05 Current monitor unit selection 03A7 F6-06 Torque reference/torque limit selection from communications option card 0400 H1-01 Terminal S3 function selection 0401 H1-02 Terminal S4 function selection 0402 H1-03 Terminal S5 function selection 0403 H1-04 Terminal S6 function selection 0404 H1-05 Terminal S7 function selection 040B H2-01 Terminal M1-M2 function selection 040C H2-02 Terminal M3-M4 function selection 040D H2-03 Terminal M5-M6 function selection 0410 H3-01 AI-14B Channel 1 signal level selection 0411 H3-02 AI-14B Channel 1 gain 0412 H3-03 AI-14B Channel 1 bias 0413 H3-04 AI-14B Channel 3 signal level selection 0414 H3-05 AI-14B Channel 3 function selection 0415 H3-06 AI-14B Channel 3 gain 0416 H3-07 AI-14B Channel 3 bias 0417 H3-08 AI-14B Channel 2 signal level selection 0418 H3-09 AI-14B Channel 2 function selection 0419 H3-10 AI-14B Channel 2 gain 041A H3-11 AI-14B Channel 2 bias 041B H3-12 Analog input filter time parameter 0434 H3-15 Terminal A1 function selection 0435 H3-16 Terminal A1 input gain 0436 H3-17 Terminal A1 input bias 0425 H5-01 Slave address 0426 H5-02 Communication speed selection 0427 H5-03 Communication parity selection 0428 H5-04 Stopping method after communication error 0429 H5-05 Communication error detection selection 042A H5-06 Send wait time 042B H5-07 RTS control ON/OFF 0480 L1-01 Motor protection selection 0481 L1-02 Motor protection time constant 0489 L2-05 Undervoltage detection level 04CB L2-11 Battery Voltage 048F L3-01 Stall prevention selection during accel 0490 L3-02 Stall prevention level during accel 0491 L3-03 Stall prevention limit during accel 0492 L3-04 Stall prevention selection during decel 0493 L3-05 Stall prevention selection during running 0494 L3-06 Stall prevention level during running 0499 L4-01 Speed agreement detection level 049A L4-02 Speed agreement detection width 049B L4-03 Speed agreement detection level (+/-) 049C L4-04 Speed agreement detection width (+/-) 049D L4-05 Operation when frequency reference is missing 04C2 L4-06 Frequency reference when frequency reference is lost 049E L5-01 Number of auto restart attempts 049F L5-02 Auto restart operation selection 04A0 L5-03 Abnormal retry interval time 04CC L5-05 Under voltage fault restart selection 04A1 L6-01 Torque detection selection 1 04A2 L6-02 Torque detection level 1 04A3 L6-03 Torque detection time 1 04A4 L6-04 Torque detection selection 2 04A5 L6-05 Torque detection level 2 04A6 L6-06 Torque detection time 2 04A7 L7-01 Forward drive torque limit 04A8 L7-02 Reverse drive torque limit 04A9 L7-03 Forward regenerative torque limit 04AA L7-04 Reverse regenerative torque limit 04AC L7-06 Torque limit time parameter 04C9 L7-07 Torque Limit Operation during accel/decel 04AE L8-02 Overheat pre-alarm level 04AF L8-03 Operation selection after overheat prealarm 04B1 L8-05 Input openphase protection selection 04B3 L8-07 Output open-phase protection selection 04B5 L8-09 Ground fault detection selection 04B6 L8-10 Cooling fan control selection 04B7 L8-11 Cooling fan control delay time 04B8 L8-12 Ambient temperature 04BE L8-18 Soft CLA selection 04C0 L8-20 Output phase loss detection time 04E2 L8-32 OH1 detection during cooling fan failure 0584 N2-01 Speed feedback detection control (AFR) gain 0585 N2-02 Speed feedback detection control (AFR) time constant 0586 N2-03 Speed feedback detection control (AFR) time constant 2 05B0 N5-01 Feed forward control selection 05B1 N5-02 Motor acceleration time 05B2 N5-03 Feed forward proportional gain 0540 N8-01 Initial magnetic polarity estimation current 0562 N8-35 Magnet position detection method 0563 N8-36 Magnet position detection method 2 frequency 0564 N8-37 Magnet position detection method 2 current level 0566 N8-39 Low pass filter cut-off frequency for magnet position detection method 2 056D N8-46 Inductance measurement current level 064D N9-60 A/D conversion start delay time 065B N9-74 Leakage current reduction selection 0500 o1-01 Monitor selection 0501 o1-02 Monitor selection after power up 0502 o1-03 Frequency units of reference setting and monitor 0503 o1-04 Setting unit for frequency constants related to V/f characteristics 0504 o1-05 LCD Display contrast adjustment 0505 o2-01 LOCAL/REMOTE key enable/disable 0506 o2-02 STOP key during control circuit terminal operation 0507 o2-03 Parameter initial value 0508 o2-04 kVA selection 0509 o2-05 Frequency reference setting method selection 050A o2-06 Operation selection when digital operator is disconnected 050B o2-07 Cumulative operation time setting 050C o2-08 Cumulative operation time selection 050D o2-09 Initialization mode 050E o2-10 Fan operation time setting 0510 o2-12 Fault trace initialize 0513 o2-15 Number of Travels counter initialize 0515 o3-01 Copy function selection 0516 o3-02 Read permitted selection 0680 S1-01 Zero speed level at stop 0681 S1-02 DC injection braking current at start 0682 S1-03 DC injection braking current at stop 0683 S1-04 DC injection braking/zerospeed time at start 0684 S1-05 DC injection braking/zerospeed time at stop 0685 S1-06 Brake release delay time 0686 S1-07 Brake close delay time 068D S1-14 SE2 detection delay time 068E S1-15 SE3 detection delay time 068F S1-16 Run delay time 0690 S1-17 DC injection current gain at regenerative operation 0691 S1-18 DC injection current gain at motoring operation 0692 S1-19 Magnetic contactor open delay time 0693 S1-20 Zero servo gain 0694 S1-21 Zero-servo completion width 0695 S1-22 Starting torque compensation increase time 0696 S1-23 Torque compensation gain during lowering 0697 S1-24 Torque compensation bias during raising 0698 S1-25 Torque compensation bias during lowering 0699 S1-26 Torque compensation gain during lowering 069A S1-27 Door zone speed level 069B S1-28 SE1 selection 069E S1-31 Torque limit time at stop 06AE S2-01 Motor rated speed 06AF S2-02 Slip compensation gain in motoring mode 06B0 S2-03 Slip compensation gain in regenerative mode 06B4 S2-07 Slip compensation delay time 06BC S2-15 Slip compensation selection during regeneration 06BD S3-01 Short floor function selection 06C4 S3-08 Output phase order 06C5 S3-09 Frequency reference loss fault detection 06C9 S3-13 Traction sheave diameter 06CA S3-14 Roping 06CC S3-16 Over acceleration detection level 06CD S3-17 Over acceleration detection filter time 06CE S3-18 Over acceleration detection selection 06D3 S3-23 Distance calculation deceleration time gain 0701 T1-01 Autotuning mode selection 0702 T1-02 Motor output power 0703 T1-03 Motor rated voltage 0704 T1-04 Motor rated current 0705 T1-05 Motor base frequency 0706 T1-06 Number of motor poles 0707 T1-07 Motor base speed 0708 T1-08 Number of PG pulses 0709 T1-09 Motor noload current 0730 T2-01 Motor output power 0731 T2-02 Motor base frequency 0732 T2-03 Motor rated voltage 0733 T2-04 Motor rated current 0734 T2-05 Number of motor poles 0735 T2-06 Motor d axis inductance 0737 T2-08 Motor voltage parameter 0738 T2-09 Number of PG pulses 072F T2-10 Motor voltage parameter calculation selection 0040 U1-01 Frequency reference 0041 U1-02 Output frequency 0042 U1-03 Output current 0043 U1-04 Control method 0044 U1-05 Motor speed 0045 U1-06 Output voltage 0046 U1-07 DC bus voltage 0047 U1-08 Output power 0048 U1-09 Torque reference 0049 U1-10 Input terminal status 004A U1-11 Output terminal status 004B U1-12 Operation status 004C U1-13 Cumulative operation time 004D U1-14 Software No. (flash memory) 004E U1-15 Terminal A1 or A1-14B channel 1 input voltage level 004F U1-16 AI-14B channel 2 input voltage level 0050 U1-17 AI-14B channel 3 input voltage level 0051 U1-18 Motor secondary current (Iq) 0052 U1-19 Motor exciting current (Id) 0053 U1-20 Frequency reference after softstarter 0054 U1-21 ASR input 0055 U1-22 ASR output 0058 U1-25 DI-16H2 input status 0059 U1-26 Output voltage reference (Vq) 005A U1-27 Output voltage reference (Vd) 005B U1-28 Software No. (CPU) 005F U1-32 ACR output of q axis 0060 U1-33 ACR output of d axis 0061 U1-34 OPE fault constant 0062 U1-35 Zero-servo movement pulses 0066 U1-39 MEMOBUS communications error code 0067 U1-40 Cooling fan operating time 0068 U1-41 Heatsink Temperature 006B U1-44 ASR output without filter 006C U1-45 Feed forward control output 0071 U1-50 Slip compensation value 0072 U1-51 Max Current during acceleration 0073 U1-52 Max Current during deceleration 0074 U1-53 Max Current during Top speed 0075 U1-54 Max Current during leveling speed 0076 U1-55 Operation counter 0077 U1-56 AI-14B channel 1 input voltage level 0078 U1-57 Car acceleration rate 07C6 U1-74 q-axis motor current reference 07C7 U1-75 d-axis motor current reference 0080 U2-01 Current fault 0081 U2-02 Last fault 0082 U2-03 Reference frequency at fault 0083 U2-04 Output frequency at fault 0084 U2-05 Output current at fault 0085 U2-06 Motor speed at fault 0086 U2-07 Output voltage reference at fault 0087 U2-08 DC bus voltage at fault 0088 U2-09 Output power at fault 0089 U2-10 Torque reference at fault 008A U2-11 Input terminal status at fault 008B U2-12 Output terminal status at fault 008C U2-13 Operation status at fault 008D U2-14 Cumulative operation time at fault 07E0 U2-15 Soft Starter Speed Reference at Fault 07E1 U2-16 q-Axis Current at Fault 07E2 U2-17 d-Axis Current at Fault 0090 U3-01 Last fault 0091 U3-02 Second last fault 0092 U3-03 Third last fault 0093 U3-04 Fourth last fault 0094 U3-05 Cumulative operation time at fault 0095 U3-06 Accumulated time of second fault 0096 U3-07 Accumulated time of third fault 0097 U3-08 Accumulated time of fourth fault 0804 U3-09 Fifth last fault 0805 U3-10 Sixth last fault 0806 U3-11 Seventh last fault 0807 U3-12 Eighth last fault 0808 U3-13 Ninth last fault 0809 U3-14 Tenth last fault 080E U3-15 Accumulated time of fifth fault 080F U3-16 Accumulated time of sixth fault 0810 U3-17 Accumulated time of secenth fault 0811 U3-18 Accumulated time of eighth fault 0812 U3-19 Accumulated time of ninth fault 0813 U3-20 Accumulated time of tenth fault 0800 U3-01 Last fault 0801 U3-02 Second last fault 0802 U3-03 Third last fault 0803 U3-04 Fourth last fault 080A U3-05 Cumulative operation time at fault 080B U3-06 Accumulated time of second fault 080C U3-07 Accumulated time of third fault 080D U3-08 Accumulated time of fourth fault [SigDataEnd] [SigData]-B 0001.0 Forward Run/Stop Command 1: Forward run 0: Stop 0001.1 Reverse Run/Stop Command 1: Reverse run 0: Stop 0001.2 External fault 1: Error (EFO) 0001.3 Fault reset 1: Reset command 0001.4 ComNet 0001.5 ComCtrl 0001.6 Multi-function input command 3 0001.7 Multi-function input command 4 0001.8 Multi-function input command 5 0001.9 Multi-function input command 6 0001.A Multi-function input command 7 0002 Frequency reference (Set units using constant o1-03) 0007 Analog output 1 setting (-11 V/-1540 to 11 V/1540) 0008 Analog output 2 setting (-11 V/-1540 to 11 V/1540) 0009.0 Contact output (Terminal M1-M2) 1: ON 0: OFF 0009.1 Contact output (Terminal M3-M4) 1: ON 0: OFF 0009.2 Contact output (Terminal M5-M6) 1: ON 0: OFF 0009.6 Set error contact (terminal MA-MC) output using bit 7. 1: ON 0: OFF 0009.7 Error contact (terminal MA-MC) 1: ON 0: OFF 000F.C Broadcast data terminal S5 input 1: Enabled 0: Disabled 000F.D Broadcast data terminal S6 input 1: Enabled 0: Disabled 000F.E Broadcast data terminal S7 input 1: Enabled 0: Disabled 0020.0 Operation 1: Operating 0: Stopped 0020.1 Reverse operation 1: Reverse operation 0: Forward operation 0020.2 Inverter startup complete 1: Completed 2: Not completed 0020.3 Error 1: Error 0020.4 Data setting error 1: Error 0020.5 Multi-function contact output (terminal M1 - M2) 1: ON 0: OFF 0020.6 Multi-function contact output1 (terminal M3 - M4) 1: ON 0: OFF 0020.7 Multi-function contact output2 (terminal M5 - M6) 1: ON 0: OFF 0021.0 Overcurrent (OC) Ground fault (GF) 0021.1 Main circuit overvoltage (OV) 0021.2 Inverter overload (OL2) 0021.3 Inverter overheat (OH1, OH2) 0021.4 Injection brake transistor resistance overheat (rr, rH) 0021.5 Fuse blown (PUF) 0021.6 PID feedback reference lost (FbL) 0021.7 External fault (EF, EFO) 0021.8 Hardware error (CPF) 0021.9 Motor overload (OL1), overtorque 1 (OL3) detected, or overtorque 2 (OL4) detected 0021.A PG broken wire detected (PGO), Overspeed (OS), Speed deviation (DEV) 0021.B Main circuit undervoltage (UV) detected 0021.C Main circuit undervoltage (UV1), control power supply error (UV2), inrush prevention circuit error (UV3), power loss 0021.D Main Circuit Voltage Fault (PF), Output Open-phase (LF) 0021.E MEMOBUS communications error (CE) 0021.F Operator disconnected (OPR) 0022.0 Writing data 0022.3 Upper and lower limit errors 0022.4 Data integrity error 0023 Frequency reference (U1-01) 0024 Output frequency (U1-02) 0025 Output voltage reference (U1-06) 0026 Output current (U1-03) (Unit: 1/0.1A) 0027 Output power (U1-08) 0028 Torque reference (U1-09) 002B.0 Multi-function contact input terminal S1 1: ON, 0: OFF 002B.1 Multi-function contact input terminal S2 1: ON, 0: OFF 002B.2 Multi-function contact input terminal S3 1: ON, 0: OFF 002B.3 Multi-function contact input terminal S4 1: ON, 0: OFF 002B.4 Multi-function contact input terminal S5 1: ON, 0: OFF 002B.5 Multi-function contact input terminal S6 1: ON, 0: OFF 002B.6 Multi-function contact input terminal S7 1: ON, 0: OFF 002C.0 Operation 1: Operating 002C.1 Zero-speed 1: Zero-speed 002C.2 Frequency matching 1: Matched 002C.3 User-defined speed matching 1: Matched 002C.4 Frequency detection 1 1: Output frequency ≤ L4-01 002C.5 Frequency detection 2 1: Output frequency ≥ L4-01 002C.6 Inverter startup completed 1: Startup completed 002C.7 Low voltage detection 1: Detected 002C.8 Baseblock 1: Inverter output baseblock 002C.9 Speed (frequency) reference mode 1: Not communications 0: Communications 002C.A Run Command mode 1: Not communications 0: Communications 002C.B Overtorque detection 1: Detected 002C.C Speed (frequency) reference lost 1: Lost 002C.D Retrying error 1: Retrying 002C.E Error (including MEMOBUS communications time-out) 1:Error occurred 002C.F MEMOBUS communications time-out 1: Timed out 002D.0 Multi-function contact output (terminal M1-M2) 1: ON 0: OFF 002D.1 Multi-function contact output1 (terminal M3-M4) 1: ON 0: OFF 002D.2 Multi-function contact output2 (terminal M5-M6) 1: ON 0: OFF 0031 Main circuit DC voltage 0032 Torque monitor (Unit: 1/0.1%) 0033 Output power (U1-08) 003B CPU software number 003C Flash software number 003D.0 CRC error 003D.1 Invalid data length 003D.3 Parity error 003D.4 Overrun error 003D.5 Framing error 003D.6 Time-out 003E kVA setting 003F Control method 0900 Write constant data to EEPROM 0910 Constant data is not written to EEPROM, but refreshed in RAM only. 0100 A1-00 Language selection for Digital Operator display 0101 A1-01 Constant access level 0102 A1-02 Control method selection 0103 A1-03 Initialize 0104 A1-04 Password 0105 A1-05 Password setting 0106 A2-01 User specified parameters 0107 A2-02 User specified parameters 0108 A2-03 User specified parameters 0109 A2-04 User specified parameters 010A A2-05 User specified parameters 010B A2-06 User specified parameters 010C A2-07 User specified parameters 010D A2-08 User specified parameters 010E A2-09 User specified parameters 010F A2-10 User specified parameters 0110 A2-11 User specified parameters 0111 A2-12 User specified parameters 0112 A2-13 User specified parameters 0113 A2-14 User specified parameters 0114 A2-15 User specified parameters 0115 A2-16 User specified parameters 0116 A2-17 User specified parameters 0117 A2-18 User specified parameters 0118 A2-19 User specified parameters 0119 A2-20 User specified parameters 011A A2-21 User specified parameters 011B A2-22 User specified parameters 011C A2-23 User specified parameters 011D A2-24 User specified parameters 011E A2-25 User specified parameters 011F A2-26 User specified parameters 0120 A2-27 User specified parameters 0121 A2-28 User specified parameters 0122 A2-29 User specified parameters 0123 A2-30 User specified parameters 0124 A2-31 User specified parameters 0125 A2-32 User specified parameters 0180 b1-01 Reference rource selection 0181 b1-02 Run Command source selection 0182 b1-03 Stopping method selection 0185 b1-06 Control input scan 0186 b1-07 Operation selection after switching to remote mode 0187 b1-08 Run Command selection in programming modes 0190 b2-08 Magnetic flux compensation volume 01A3 b4-01 Timer function ON-delay time 01A4 b4-02 Timer function OFF-delay time 01B6 b6-01 Dwell frequency at start 01B7 b6-02 Dwell time at start 01B8 b6-03 Dwell frequency at stop 01B9 b6-04 Dwell time at stop 01CA b7-01 Droop control gain 01CB b7-02 Droop control delay time 01CC b8-01 Energy-saving mode selection 01F8 b8-16 Energy savings control parameter Ki 01F9 b8-17 Energy savings control parameter Kt 0200 C1-01 Acceleration time 1 0201 C1-02 Deceleration time 1 0202 C1-03 Acceleration time 2 0203 C1-04 Deceleration time 2 0204 C1-05 Acceleration time 3 0205 C1-06 Deceleration time 3 0206 C1-07 Acceleration time 4 0207 C1-08 Deceleration time 4 0208 C1-09 Fast stop time 0209 C1-10 Accel/decel time setting unit 020A C1-11 Accel/decel time switching frequency 020B C2-01 S-curve characteristic time at acceleration start 020C C2-02 S-curve characteristic time at acceleration end 020D C2-03 S-curve characteristic time at deceleration start 020E C2-04 S-curve characteristic time at deceleration end 0232 C2-05 S character characteristic time below leveling speed 020F C3-01 Slip compensation gain 0210 C3-02 Slip compensation primary delay time 0211 C3-03 Slip compensation limit 0212 C3-04 Slip compensation selection during regeneration 0213 C3-05 Output voltage limit operation selection 0215 C4-01 Torque compensation gain 0216 C4-02 Torque compensation delay time parameter 0217 C4-03 Starting torque compensation (FWD) 0218 C4-04 Starting torque compensation (REV) 0219 C4-05 Starting torque compensation time parameter 021A C4-06 Torque compensation primary delay time 2 021B C5-01 ASR proportional (P) gain 1 021C C5-02 ASR integral (I) time 1 021D C5-03 ASR proportional (P) gain 2 021E C5-04 ASR integral (I) time 2 0220 C5-06 ASR primary delay time 0221 C5-07 ASR switching frequency 0222 C5-08 ASR integral (I) limit 022E C5-09 ASR proportional (P) gain 3 0231 C5-10 ASR integral (I) time 3 0238 C5-15 ASR gain for encoder offset tuning 0224 C6-02 Carrier frequency selection 0225 C6-03 Carrier frequency upper limit 022B C6-09 Carrier during rotational autotuning 022C C6-10 Carrier during stationary autotuning 022D C6-11 Carrier frequency selection 2 0280 d1-01 Frequency reference 1 0281 d1-02 Frequency reference 2 0282 d1-03 Frequency reference 3 0283 d1-04 Frequency reference 4 0284 d1-05 Frequency reference 5 0285 d1-06 Frequency reference 6 0286 d1-07 Frequency reference 7 0287 d1-08 Frequency reference 8 0288 d1-09 Nominal speed reference 028B d1-10 Intermediate speed 1 reference 028C d1-11 Intermediate speed 2 reference 028D d1-12 Intermediate speed 3 reference 028E d1-13 Releveling speed reference 028F d1-14 Inspection speed reference 0292 d1-17 Leveling speed reference 02A7 d1-18 Speed priority selection 02A2 d6-03 Field forcing function selection 02A5 d6-06 Field forcing limit value 0300 E1-01 Input voltage setting 0302 E1-03 V/f pattern selection 0303 E1-04 Max. output frequency (FMAX) 0304 E1-05 Max. output voltage (VMAX) 0305 E1-06 Base frequency (FA) 0306 E1-07 Mid. output frequency (FB) 0307 E1-08 Mid. Output frequency voltage (VB) 0308 E1-09 Min. output frequency (FMIN) 0309 E1-10 Min. output frequency voltage (VMIN) 030C E1-13 Base voltage (VBASE) 030E E2-01 Motor rated current 030F E2-02 Motor rated slip 0310 E2-03 Motor noload current 0311 E2-04 Number of motor poles 0312 E2-05 Motor line-to-line resistance 0313 E2-06 Motor leak inductance 0314 E2-07 Motor iron saturation coefficient 1 0315 E2-08 Motor iron saturation coefficient 2 0316 E2-09 Motor mechanical loss 0317 E2-10 Motor iron loss for torque compensation 0318 E2-11 Motor rated output power 0328 E2-12 Motor iron saturation coefficient 3 032A E5-02 Motor rated power 032B E5-03 Motor rated current 032C E5-04 Number of motor poles 032D E5-05 Motor line-to-line resistance 032E E5-06 d-axis inductance 032F E5-07 q-axis inductance 0331 E5-09 Motor voltage parameter 0333 E5-11 PG home position offset 0380 F1-01 PG constant 0381 F1-02 Operation selection at PG open circuit (PGO) 0382 F1-03 Operation selection at overspeed (OS) 0383 F1-04 Operation selection at deviation 0384 F1-05 PG rotation 0385 F1-06 PG division rate (PG pulse monitor) 0387 F1-08 Overspeed detection level 0388 F1-09 Overspeed detection delay time 0389 F1-10 Excessive speed deviation detection level 038A F1-11 Excessive speed deviation detection delay time 038D F1-14 PG open-circuit detection time 03AD F1-18 DV3 fault detection selection 03AE F1-19 DV4 fault detection selection 03B0 F1-21 Absolute encoder resolution 03B1 F1-22 Magnet position offset 03B4 F1-25 Encoder copy selection 03B5 F1-26 Encoder copy write permission selection 0391 F4-01 Channel 1 monitor selection 0392 F4-02 Channel 1 gain 0393 F4-03 Channel 2 monitor selection 0394 F4-04 Channel 2 gain 0395 F4-05 Channel 1 output monitor bias 0396 F4-06 Channel 2 output monitor bias 0397 F4-07 Analog output signal level for channel 1 0398 F4-08 Analog output signal level for channel 2 0399 F5-01 Channel 1 output selection 039A F5-02 Channel 2 output selection 039B F5-03 Channel 3 output selection 039C F5-04 Channel 4 output selection 039D F5-05 Channel 5 output selection 039E F5-06 Channel 6 output selection 039F F5-07 Channel 7 output selection 03A0 F5-08 Channel 8 output selection 03A1 F5-09 DO-08 output mode selection 03A2 F6-01 Operation selection after communications error 03A3 F6-02 Input level of external fault from communications option card 03A4 F6-03 Stopping method for external fault from communications option card 03A5 F6-04 Trace sampling from communications option card 03A6 F6-05 Current monitor unit selection 03A7 F6-06 Torque reference/torque limit selection from communications option card 0400 H1-01 Terminal S3 function selection 0401 H1-02 Terminal S4 function selection 0402 H1-03 Terminal S5 function selection 0403 H1-04 Terminal S6 function selection 0404 H1-05 Terminal S7 function selection 040B H2-01 Terminal M1-M2 function selection 040C H2-02 Terminal M3-M4 function selection 040D H2-03 Terminal M5-M6 function selection 0410 H3-01 AI-14B Channel 1 signal level selection 0411 H3-02 AI-14B Channel 1 gain 0412 H3-03 AI-14B Channel 1 bias 0413 H3-04 AI-14B Channel 3 signal level selection 0414 H3-05 AI-14B Channel 3 function selection 0415 H3-06 AI-14B Channel 3 gain 0416 H3-07 AI-14B Channel 3 bias 0417 H3-08 AI-14B Channel 2 signal level selection 0418 H3-09 AI-14B Channel 2 function selection 0419 H3-10 AI-14B Channel 2 gain 041A H3-11 AI-14B Channel 2 bias 041B H3-12 Analog input filter time parameter 0434 H3-15 Terminal A1 function selection 0435 H3-16 Terminal A1 input gain 0436 H3-17 Terminal A1 input bias 0425 H5-01 Slave address 0426 H5-02 Communication speed selection 0427 H5-03 Communication parity selection 0428 H5-04 Stopping method after communication error 0429 H5-05 Communication error detection selection 042A H5-06 Send wait time 042B H5-07 RTS control ON/OFF 0480 L1-01 Motor protection selection 0481 L1-02 Motor protection time constant 0489 L2-05 Undervoltage detection level 04CB L2-11 Battery Voltage 048F L3-01 Stall prevention selection during accel 0490 L3-02 Stall prevention level during accel 0491 L3-03 Stall prevention limit during accel 0492 L3-04 Stall prevention selection during decel 0493 L3-05 Stall prevention selection during running 0494 L3-06 Stall prevention level during running 0499 L4-01 Speed agreement detection level 049A L4-02 Speed agreement detection width 049B L4-03 Speed agreement detection level (+/-) 049C L4-04 Speed agreement detection width (+/-) 049D L4-05 Operation when frequency reference is missing 04C2 L4-06 Frequency reference when frequency reference is lost 049E L5-01 Number of auto restart attempts 049F L5-02 Auto restart operation selection 04A0 L5-03 Abnormal retry interval time 04CC L5-05 Under voltage fault restart selection 04A1 L6-01 Torque detection selection 1 04A2 L6-02 Torque detection level 1 04A3 L6-03 Torque detection time 1 04A4 L6-04 Torque detection selection 2 04A5 L6-05 Torque detection level 2 04A6 L6-06 Torque detection time 2 04A7 L7-01 Forward drive torque limit 04A8 L7-02 Reverse drive torque limit 04A9 L7-03 Forward regenerative torque limit 04AA L7-04 Reverse regenerative torque limit 04AC L7-06 Torque limit time parameter 04C9 L7-07 Torque Limit Operation during accel/decel 04AE L8-02 Overheat pre-alarm level 04AF L8-03 Operation selection after overheat prealarm 04B1 L8-05 Input openphase protection selection 04B3 L8-07 Output open-phase protection selection 04B5 L8-09 Ground fault detection selection 04B6 L8-10 Cooling fan control selection 04B7 L8-11 Cooling fan control delay time 04B8 L8-12 Ambient temperature 04BE L8-18 Soft CLA selection 04C0 L8-20 Output phase loss detection time 04E2 L8-32 OH1 detection during cooling fan failure 0584 N2-01 Speed feedback detection control (AFR) gain 0585 N2-02 Speed feedback detection control (AFR) time constant 0586 N2-03 Speed feedback detection control (AFR) time constant 2 05B0 N5-01 Feed forward control selection 05B1 N5-02 Motor acceleration time 05B2 N5-03 Feed forward proportional gain 0540 N8-01 Initial magnetic polarity estimation current 0562 N8-35 Magnet position detection method 0563 N8-36 Magnet position detection method 2 frequency 0564 N8-37 Magnet position detection method 2 current level 0566 N8-39 Low pass filter cut-off frequency for magnet position detection method 2 056D N8-46 Inductance measurement current level 064D N9-60 A/D conversion start delay time 065B N9-74 Leakage current reduction selection 0500 o1-01 Monitor selection 0501 o1-02 Monitor selection after power up 0502 o1-03 Frequency units of reference setting and monitor 0503 o1-04 Setting unit for frequency constants related to V/f characteristics 0504 o1-05 LCD Display contrast adjustment 0505 o2-01 LOCAL/REMOTE key enable/disable 0506 o2-02 STOP key during control circuit terminal operation 0507 o2-03 Parameter initial value 0508 o2-04 kVA selection 0509 o2-05 Frequency reference setting method selection 050A o2-06 Operation selection when digital operator is disconnected 050B o2-07 Cumulative operation time setting 050C o2-08 Cumulative operation time selection 050D o2-09 Initialization mode 050E o2-10 Fan operation time setting 0510 o2-12 Fault trace initialize 0513 o2-15 Number of Travels counter initialize 0515 o3-01 Copy function selection 0516 o3-02 Read permitted selection 0680 S1-01 Zero speed level at stop 0681 S1-02 DC injection braking current at start 0682 S1-03 DC injection braking current at stop 0683 S1-04 DC injection braking/zerospeed time at start 0684 S1-05 DC injection braking/zerospeed time at stop 0685 S1-06 Brake release delay time 0686 S1-07 Brake close delay time 068D S1-14 SE2 detection delay time 068E S1-15 SE3 detection delay time 068F S1-16 Run delay time 0690 S1-17 DC injection current gain at regenerative operation 0691 S1-18 DC injection current gain at motoring operation 0692 S1-19 Magnetic contactor open delay time 0693 S1-20 Zero servo gain 0694 S1-21 Zero-servo completion width 0695 S1-22 Starting torque compensation increase time 0696 S1-23 Torque compensation gain during lowering 0697 S1-24 Torque compensation bias during raising 0698 S1-25 Torque compensation bias during lowering 0699 S1-26 Torque compensation gain during lowering 069A S1-27 Door zone speed level 069B S1-28 SE1 selection 069E S1-31 Torque limit time at stop 06AE S2-01 Motor rated speed 06AF S2-02 Slip compensation gain in motoring mode 06B0 S2-03 Slip compensation gain in regenerative mode 06B4 S2-07 Slip compensation delay time 06BC S2-15 Slip compensation selection during regeneration 06BD S3-01 Short floor function selection 06C4 S3-08 Output phase order 06C5 S3-09 Frequency reference loss fault detection 06C9 S3-13 Traction sheave diameter 06CA S3-14 Roping 06CC S3-16 Over acceleration detection level 06CD S3-17 Over acceleration detection filter time 06CE S3-18 Over acceleration detection selection 06D3 S3-23 Distance calculation deceleration time gain 0701 T1-01 Autotuning mode selection 0702 T1-02 Motor output power 0703 T1-03 Motor rated voltage 0704 T1-04 Motor rated current 0705 T1-05 Motor base frequency 0706 T1-06 Number of motor poles 0707 T1-07 Motor base speed 0708 T1-08 Number of PG pulses 0709 T1-09 Motor noload current 0730 T2-01 Motor output power 0731 T2-02 Motor base frequency 0732 T2-03 Motor rated voltage 0733 T2-04 Motor rated current 0734 T2-05 Number of motor poles 0735 T2-06 Motor d axis inductance 0737 T2-08 Motor voltage parameter 0738 T2-09 Number of PG pulses 072F T2-10 Motor voltage parameter calculation selection 0040 U1-01 Frequency reference 0041 U1-02 Output frequency 0042 U1-03 Output current 0043 U1-04 Control method 0044 U1-05 Motor speed 0045 U1-06 Output voltage 0046 U1-07 DC bus voltage 0047 U1-08 Output power 0048 U1-09 Torque reference 0049.0 U1-10 1:FWD command(S1) is ON (Input terminal status) 0049.1 U1-10 1:REV command(S2) is ON (Input terminal status) 0049.2 U1-10 1:Multi input 1(S3) is ON (Input terminal status) 0049.3 U1-10 1:Multi input 2(S4) is ON (Input terminal status) 0049.4 U1-10 1:Multi input 3(S5) is ON (Input terminal status) 0049.5 U1-10 1:Multi input 4(S6) is ON (Input terminal status) 0049.6 U1-10 1:Multi input 5(S7) is ON (Input terminal status) 004A.0 U1-11 1:Multi-function contact output 1(M1-M2) is ON (Output terminal status) 004A.1 U1-11 1:Multi-function contact output 2(M3-M4) is ON (Output terminal status) 004A.2 U1-11 1:Multi-function contact output 3(M5-M6) is ON (Output terminal status) 004A.8 U1-11 1:Error output(MA/MB-MC) (Output terminal status) 004B.0 U1-12 1:Run (Operation status) 004B.1 U1-12 1:Zero speed (Operation status) 004B.2 U1-12 1:Reverse (Operation status) 004B.3 U1-12 1:Reset signal input (Operation status) 004B.4 U1-12 1:Speed agree (Operation status) 004B.5 U1-12 1:Inverter ready (Operation status) 004B.6 U1-12 1:Minor fault (Operation status) 004B.7 U1-12 1:Major fault (Operation status) 004C U1-13 Cumulative operation time 004D U1-14 Software No. (flash memory) 004E U1-15 Terminal A1 or A1-14B channel 1 input voltage level 004F U1-16 AI-14B channel 2 input voltage level 0050 U1-17 AI-14B channel 3 input voltage level 0051 U1-18 Motor secondary current (Iq) 0052 U1-19 Motor exciting current (Id) 0053 U1-20 Frequency reference after softstarter 0054 U1-21 ASR input 0055 U1-22 ASR output 0058 U1-25 DI-16H2 input status 0059 U1-26 Output voltage reference (Vq) 005A U1-27 Output voltage reference (Vd) 005B U1-28 Software No. (CPU) 005F U1-32 ACR output of q axis 0060 U1-33 ACR output of d axis 0061 U1-34 OPE fault constant 0062 U1-35 Zero-servo movement pulses 0066.0 U1-39 1:CRC error (MEMOBUS communications error code) 0066.1 U1-39 1:Data length error (MEMOBUS communications error code) 0066.3 U1-39 1:Parity error (MEMOBUS communications error code) 0066.4 U1-39 1:Overrun error (MEMOBUS communications error code) 0066.5 U1-39 1:Framing error (MEMOBUS communications error code) 0066.6 U1-39 1:Timeout (MEMOBUS communications error code) 0067 U1-40 Cooling fan operating time 0068 U1-41 Heatsink Temperature 006B U1-44 ASR output without filter 006C U1-45 Feed forward control output 0071 U1-50 Slip compensation value 0072 U1-51 Max Current during acceleration 0073 U1-52 Max Current during deceleration 0074 U1-53 Max Current during Top speed 0075 U1-54 Max Current during leveling speed 0076 U1-55 Operation counter 0077 U1-56 AI-14B channel 1 input voltage level 0078 U1-57 Car acceleration rate 07C6 U1-74 q-axis motor current reference 07C7 U1-75 d-axis motor current reference 0080 U2-01 Current fault 0081 U2-02 Last fault 0082 U2-03 Reference frequency at fault 0083 U2-04 Output frequency at fault 0084 U2-05 Output current at fault 0085 U2-06 Motor speed at fault 0086 U2-07 Output voltage reference at fault 0087 U2-08 DC bus voltage at fault 0088 U2-09 Output power at fault 0089 U2-10 Torque reference at fault 008A U2-11 Input terminal status at fault 008B U2-12 Output terminal status at fault 008C U2-13 Operation status at fault 008D U2-14 Cumulative operation time at fault 07E0 U2-15 Soft Starter Speed Reference at Fault 07E1 U2-16 q-Axis Current at Fault 07E2 U2-17 d-Axis Current at Fault 0090 U3-01 Last fault 0091 U3-02 Second last fault 0092 U3-03 Third last fault 0093 U3-04 Fourth last fault 0094 U3-05 Cumulative operation time at fault 0095 U3-06 Accumulated time of second fault 0096 U3-07 Accumulated time of third fault 0097 U3-08 Accumulated time of fourth fault 0804 U3-09 Fifth last fault 0805 U3-10 Sixth last fault 0806 U3-11 Seventh last fault 0807 U3-12 Eighth last fault 0808 U3-13 Ninth last fault 0809 U3-14 Tenth last fault 080E U3-15 Accumulated time of fifth fault 080F U3-16 Accumulated time of sixth fault 0810 U3-17 Accumulated time of secenth fault 0811 U3-18 Accumulated time of eighth fault 0812 U3-19 Accumulated time of ninth fault 0813 U3-20 Accumulated time of tenth fault 0800 U3-01 Last fault 0801 U3-02 Second last fault 0802 U3-03 Third last fault 0803 U3-04 Fourth last fault 080A U3-05 Cumulative operation time at fault 080B U3-06 Accumulated time of second fault 080C U3-07 Accumulated time of third fault 080D U3-08 Accumulated time of fourth fault [SigDataEnd]-B