Name=Inverter
V1000
MaxSigCnt=0
DataFormat=Hex

[SigData]
0001	Operation signal
0002	Frequency Reference
0003	V/f gain
0006	PID Target (0.01% signed)
0007	Analog output 1 setting (10 V/4000 H)
0008	Analog output 2 setting (10 V/4000 H)
0009	Settings for Multi-Function Digital Outputs
000A	PO output
000F	Control Selection Setting
0020	Drive Status
0021	Fault Contents 1
0022	Data link status
0023	Frequency reference (U1-01)
0024	Output frequency (U1-02)
0025	Output voltage reference (U1-06) (Unit: 1/0.1V)
0026	Output current (U1-03) (Unit: 10/1A)
0027	Output power (U1-08)
0028	Torque reference (U1-09)
0029	Error details 2
002A	Alarm Contents1
002B	Input Terminal Status (U1-10)
002C	Drive Status 2
002D	Output Terminal Status (U1-11)
002F	Frequency Reference Bias (UP2, DOWN2) 1000/100%
0031	DC Bus Voltage (U1-07)
0032	Torque monitor (Unit: 1/1%)
0034	Production code1 [ASCII]VO
0035	Production code2 [ASCII]AO
0038	PID Feedback (100% / max. output frequency; 1/0.1% resolution; not signed)
0039	PID Input (100% / max. output frequency; 1/0.1% resolution; signed)
003A	PID Output (100% / max. output frequency; 1/0.1% resolution; signed)
003D	Communications Error Contents
0101	A1-01	Access Level Selection
0102	A1-02	Control Method Selection
0103	A1-03	Initialize Parameters
0104	A1-04	Password 1
0105	A1-05	Password 2
0127	A1-06	Application Preset
0128	A1-07	DriveWorksEZ function selection
0106	A2-01	User Parameters 1
0107	A2-02	User Parameters 2
0108	A2-03	User Parameters 3
0109	A2-04	User Parameters 4
010A	A2-05	User Parameters 5
010B	A2-06	User Parameters 6
010C	A2-07	User Parameters 7
010D	A2-08	User Parameters 8
010E	A2-09	User Parameters 9
010F	A2-10	User Parameters 10
0110	A2-11	User Parameters 11
0111	A2-12	User Parameters 12
0112	A2-13	User Parameters 13
0113	A2-14	User Parameters 14
0114	A2-15	User Parameters 15
0115	A2-16	User Parameters 16
0116	A2-17	User Parameters 17
0117	A2-18	User Parameters 18
0118	A2-19	User Parameters 19
0119	A2-20	User Parameters 20
011A	A2-21	User Parameters 21
011B	A2-22	User Parameters 22
011C	A2-23	User Parameters 23
011D	A2-24	User Parameters 24
011E	A2-25	User Parameters 25
011F	A2-26	User Parameters 26
0120	A2-27	User Parameters 27
0121	A2-28	User Parameters 28
0122	A2-29	User Parameters 29
0123	A2-30	User Parameters 30
0124	A2-31	User Parameters 31
0125	A2-32	User Parameters 32
0126	A2-33	User Parameter Automatic Selection
0180	b1-01	Frequency Reference Selection 1
0181	b1-02	Run Command Selection 1
0182	b1-03	Stopping Method Selection
0183	b1-04	Reverse Operation Selection
0186	b1-07	Local/Remote Run Selection
0187	b1-08	Run Command Selection while in Programming Mode
01C3	b1-14	Phase Order Selection
01C4	b1-15	Frequency Reference 2
01C5	b1-16	Run Command Source 2
01C6	b1-17	Run Command at Power Up
0189	b2-01	DC Injection Braking Start Frequency
018A	b2-02	DC Injection Braking Current
018B	b2-03	DC Injection Braking Time/DC Excitation Time at Start
018C	b2-04	DC Injection Braking Time at Stop
0190	b2-08	Magnetic Flux Compensation Capacity
01BA	b2-12	Short Circuit Brake Time at Start
01BB	b2-13	Short Circuit Brake Time at Stop
0191	b3-01	Speed Search Selection
0192	b3-02	Speed Search Deactivation Current
0193	b3-03	Speed Search Deceleration Time
0195	b3-05	Speed Search Delay Time
0196	b3-06	Output Current 1 during Speed Search
019A	b3-10	Speed Search Detection Compensation Gain
019E	b3-14	Bi-Directional Speed Search Selection
01F0	b3-17	Speed Search Restart Current Level
01F1	b3-18	Speed Search Restart Detection Time
01F2	b3-19	Number of Speed Search Restarts
01C0	b3-24	Speed Search Method Selection
01C8	b3-25	Speed Search Retry Interval Time
01A3	b4-01	Timer Function On-Delay Time
01A4	b4-02	Timer Function Off-Delay Time
01A5	b5-01	PID Function Setting
01A6	b5-02	Proportional Gain Setting (P)
01A7	b5-03	Integral Time Setting (I)
01A8	b5-04	Integral Limit Setting
01A9	b5-05	Derivative Time (D)
01AA	b5-06	PID Output Limit
01AB	b5-07	PID Offset Adjustment
01AC	b5-08	PID Primary Delay Time Constant
01AD	b5-09	PID Output Level Selection
01AE	b5-10	PID Output Gain Setting
01AF	b5-11	PID Output Reverse Selection
01B0	b5-12	PID Feedback Reference Missing Detection Selection
01B1	b5-13	PID Feedback Loss Detection Level
01B2	b5-14	PID Feedback Loss Detection Time
01B3	b5-15	PID Sleep Function Start Level
01B4	b5-16	PID Sleep Delay Time
01B5	b5-17	PID Accel/Decel Time
01DC	b5-18	PID Setpoint Selection
01DD	b5-19	PID Setpoint Value
01E2	b5-20	PID Setpoint Scaling
019F	b5-34	PID Output Lower Limit
01A0	b5-35	PID Input Limit
01A1	b5-36	PID Feedback High Detection Level
01A2	b5-37	PID Feedback High Level Detection Time
01FE	b5-38	PID Setpoint / User Display
01FF	b5-39	PID Setpoint Display Digits
01B6	b6-01	Dwell Reference at Start
01B7	b6-02	Dwell Time at Start
01B8	b6-03	Dwell Frequency at Stop
01B9	b6-04	Dwell Time at Stop
01CC	b8-01	Energy Saving Control Selection
01CD	b8-02	Energy Saving Gain
01CE	b8-03	Energy Saving Control Filter Time Constant
01CF	b8-04	Energy Saving Coefficient Value
01D0	b8-05	Power Detection Filter Time
01D1	b8-06	Search Operation Voltage Limit
0200	C1-01	Acceleration Time 1
0201	C1-02	Deceleration Time 1
0202	C1-03	Acceleration Time 2
0203	C1-04	Deceleration Time 2
0204	C1-05	Acceleration Time 3 (Motor 2 Accel Time 1)
0205	C1-06	Deceleration Time 3 (Motor 2 Decel Time 1)
0206	C1-07	Acceleration Time 4 (Motor 2 Accel Time 2)
0207	C1-08	Deceleration Time 4 (Motor 2 Decel Time 2)
0208	C1-09	Fast-Stop Time
0209	C1-10	Accel/Decel Time Setting Units
020A	C1-11	Accel/Decel Time Switching Frequency
020B	C2-01	S-Curve Characteristic at Accel Start
020C	C2-02	S-Curve Characteristic at Accel End
020D	C2-03	S-Curve Characteristic at Decel Start
020E	C2-04	S-Curve Characteristic at Decel End
020F	C3-01	Slip Compensation Gain
0210	C3-02	Slip Compensation Primary Delay Time
0211	C3-03	Slip Compensation Limit
0212	C3-04	Slip Compensation Selection during Regeneration
0213	C3-05	Output Voltage Limit Operation Selection
0215	C4-01	Torque Compensation Gain
0216	C4-02	Torque Compensation Primary Delay Time
0217	C4-03	Torque Compensation at Forward Start
0218	C4-04	Torque Compensation at Reverse Start
0219	C4-05	Torque Compensation Time Constant
021A	C4-06	Torque Compensation Primary Delay Time 2
021B	C5-01	ASR Proportional Gain 1
021C	C5-02	ASR Integral Time 1
021D	C5-03	ASR Proportional Gain 2
021E	C5-04	ASR Integral Time 2
021F	C5-05	ASR Limit
0223	C6-01	Normal/Heavy Duty Selection
0224	C6-02	Carrier Frequency Selection
0225	C6-03	Carrier Frequency Upper Limit
0226	C6-04	Carrier Frequency Lower Limit
0227	C6-05	Carrier Frequency Proportional Gain
0280	d1-01	Frequency Reference 1
0281	d1-02	Frequency Reference 2
0282	d1-03	Frequency Reference 3
0283	d1-04	Frequency Reference 4
0284	d1-05	Frequency Reference 5
0285	d1-06	Frequency Reference 6
0286	d1-07	Frequency Reference 7
0287	d1-08	Frequency Reference 8
0288	d1-09	Frequency Reference 9
028B	d1-10	Frequency Reference 10
028C	d1-11	Frequency Reference 11
028D	d1-12	Frequency Reference 12
028E	d1-13	Frequency Reference 13
028F	d1-14	Frequency Reference 14
0290	d1-15	Frequency Reference 15
0291	d1-16	Frequency Reference 16
0292	d1-17	Jog Frequency Reference
0289	d2-01	Frequency Reference Upper Limit
028A	d2-02	Frequency Reference Lower Limit
0293	d2-03	Master Speed Reference Lower Limit
0294	d3-01	Jump Frequency 1
0295	d3-02	Jump Frequency 2
0296	d3-03	Jump Frequency 3
0297	d3-04	Jump Frequency width
0298	d4-01	Frequency Reference Hold Function Selection
02AA	d4-03	Frequency Reference Bias Step (Up/Down 2)
02AB	d4-04	Frequency Reference Accel/Decel (Up/Down 2)
02AC	d4-05	Frequency Reference Bias Operation Mode Selection (Up/Down 2)
02AD	d4-06	Frequency Reference Bias (Up/Down 2)
02AE	d4-07	Analog Frequency Reference Fluctuation Limit (Up/Down 2)
02AF	d4-08	Frequency Reference Bias Upper Limit (Up/Down 2)
02B0	d4-09	Frequency Reference Bias Lower Limit (Up/Down 2)
02B6	d4-10	Up/Down Frequency Reference Limit Selection
02B8	d4-12	Stop Position Gain
02B2	d7-01	Offset Frequency 1
02B3	d7-02	Offset Frequency 2
02B4	d7-03	Offset Frequency 3
0300	E1-01	Input Voltage Setting
0302	E1-03	V/f Pattern Selection
0303	E1-04	Max Output Frequency
0304	E1-05	Max Output Voltage
0305	E1-06	Base Frequency
0306	E1-07	Mid Output Frequency
0307	E1-08	Mid Output Frequency Voltage
0308	E1-09	Minimum Output Freq.
0309	E1-10	Minimum Output Freq. Voltage
030A	E1-11	Mid Output Frequency 2
030B	E1-12	Mid Output Frequency Voltage 2
030C	E1-13	Base Voltage
030E	E2-01	Motor Rated Current
030F	E2-02	Motor Rated Slip
0310	E2-03	Motor No-Load Current
0311	E2-04	Number of Motor Poles
0312	E2-05	Motor Line-to-Line Resistance
0313	E2-06	Motor Leakage Inductance
0314	E2-07	Motor Iron-Core Saturation Coefficient 1
0315	E2-08	Motor Iron-Core Saturation Coefficient 2
0316	E2-09	Motor Mechanical Loss
0317	E2-10	Motor Iron Loss for Torque Compensation
0318	E2-11	Motor Rated Output
0328	E2-12	Motor Iron-Core Saturation Coefficient 3
0319	E3-01	Motor 2 Control Method
031A	E3-04	Motor 2 Max Output Frequency
031B	E3-05	Motor 2 Max Voltage
031C	E3-06	Motor 2 Base Frequency
031D	E3-07	Motor 2 Mid Output Freq.
031E	E3-08	Motor 2 Mid Output Freq. Voltage
031F	E3-09	Motor 2 Min. Output Freq.
0320	E3-10	Motor 2 Min. Output Freq. Voltage
0345	E3-11	Motor 2 Mid Output Frequency 2
0346	E3-12	Motor 2 Mid Output Frequency Voltage 2
0347	E3-13	Motor 2 Base Voltage
0321	E4-01	Motor 2 Rated Current
0322	E4-02	Motor 2 Rated Slip
0323	E4-03	Motor 2 Rated No-Load Current
0324	E4-04	Motor 2 Motor Poles
0325	E4-05	Motor 2 Line-to-Line Resistance
0326	E4-06	Motor 2 Leakage Inductance
0343	E4-07	Motor 2 Motor Iron-Core Saturation Coefficient 1
0344	E4-08	Motor 2 Motor Iron-Core Saturation Coefficient 2
033F	E4-09	Motor 2 Mechanical Loss
0340	E4-10	Motor 2 Iron Loss
0327	E4-11	Motor 2 Rated Capacity
0342	E4-12	Motor 2 Iron-Core Saturation Coefficient 3
033E	E4-14	Motor 2 Slip Compensation Gain
0341	E4-15	Torque Compensation Gain - Motor 2
0329	E5-01	Motor Code Selection (for PM motor)
032A	E5-02	Motor Rated Capacity (for PM motor)
032B	E5-03	Motor Rated Current
032C	E5-04	Motor Poles
032D	E5-05	Motor Resistance
032E	E5-06	Motor d Axis Inductance
032F	E5-07	Motor q Axis Inductance
0331	E5-09	Motor Induction Voltage Constant 1
0353	E5-24	Motor Induction Voltage Parameter 2
0381	F1-02	Operation Selection at PG Open Circuit (PGO)
0382	F1-03	Operation Selection at Overspeed (OS)
0383	F1-04	Operation Selection at Deviation
0387	F1-08	Overspeed Detection Level
0388	F1-09	Overspeed Detection Delay Time
0389	F1-10	Excessive Speed Deviation Detection Level
038A	F1-11	Excessive Speed Deviation Detection Delay Time
038D	F1-14	PG Open-Circuit Detection Time
03A2	F6-01	Communications Error operation Selection
03A3	F6-02	External fault from comm. Option selection
03A4	F6-03	External fault from comm. Option operation selection
03E5	F6-04	Trace Sampling Rate
03E6	F6-10	CC-Link Node Address
03E7	F6-11	CC-Link communications speed
03BB	F6-14	BUS Error auto reset
03C1	F6-20	DeviceNet MAC Address
03C2	F6-21	Device Net Communications Speed
03C3	F6-22	Device Net PCA setting
03C4	F6-23	Device Net PPA setting
03C5	F6-24	Device Net Idle mode fault detection
03CB	F6-30	Profibus node address
03CC	F6-31	Profibus Clear mode selection
03CD	F6-32	Profibus Map selections
03D0	F6-36	CANopen Node ID selection
03D1	F6-37	CANopen Communications speed
03D5	F6-40	CompoNet Node ID
03D6	F6-41	CompoNet Speed
03E5	F7-01	Ethernet IP Address 1
03E6	F7-02	Ethernet IP Address 1
03E7	F7-03	Ethernet IP Address 1
03E8	F7-04	Ethernet IP Address 1
03E9	F7-05	Subnet Mask 1
03EA	F7-06	Subnet Mask 2
03EB	F7-07	Subnet Mask 3
03EC	F7-08	Subnet Mask 4
03ED	F7-09	Gateway Address 1
03EE	F7-10	Gateway Address 2
03EF	F7-11	Gateway Address 3
03F0	F7-12	Gateway Address 4
03F1	F7-13	Dress Mode at Startup
03F2	F7-14	Security password
03F3	F7-15	Duplex Mode Selection
03F6	F7-18	Communication Speed Selection
03F7	F7-19	Web Page Access
03F8	F7-20	Gateway selection
03F9	F7-21	Communication loss time out
0438	H1-01	Multi-Function Digital Input Terminal S1 Function Selection
0439	H1-02	Multi-Function Digital Input Terminal S2 Function Selection
0400	H1-03	Multi-Function Digital Input Terminal S3 Function Selection
0401	H1-04	Multi-Function Digital Input Terminal S4 Function Selection
0402	H1-05	Multi-Function Digital Input Terminal S5 Function Selection
0403	H1-06	Multi-Function Digital Input Terminal S6 Function Selection
0404	H1-07	Multi-Function Digital Input Terminal S7 Function Selection
040B	H2-01	Terminal MA, MB and MC Function Selection (relay)
040C	H2-02	Terminal P1 Function Selection
040D	H2-03	Terminal P2 Function Selection
0437	H2-06	Watt Hour Output Unit Selection
0410	H3-01	Terminal A1 Signal Level Selection
0434	H3-02	Terminal A1 Function Selection
0411	H3-03	Terminal A1 Gain Setting
0412	H3-04	Terminal A1 Bias Setting
0417	H3-09	Terminal A2 Signal Level Selection
0418	H3-10	Terminal A2 Function Selection
0419	H3-11	Terminal A2 Gain Setting
041A	H3-12	Terminal A2 Input Bias
041B	H3-13	Analog Input Filter Time Constant
041D	H4-01	Multi-Function Analog Output Terminal AM
041E	H4-02	Multi-Function Analog Output Terminal AM Gain
041F	H4-03	Multi-Function Analog Output Terminal AM Gain
0425	H5-01	Drive Node Address
0426	H5-02	Communication Speed Selection
0427	H5-03	Communication Parity Selection
0428	H5-04	Stopping Method After Communication Error
0429	H5-05	Communication Fault Detection Selection
042A	H5-06	Drive Transmit Wait Time
042B	H5-07	RTS Control Selection
0435	H5-09	CE Detection Time
0436	H5-10	Unit Selection for MEMOBUS/Modbus Register 0025H
043C	H5-11	Communications ENTER Function Selection
043D	H5-12	Run Command Method Selection
042C	H6-01	Pulse Train Input Terminal RP Function Selection
042D	H6-02	Pulse Train Input Scaling
042E	H6-03	Pulse Train Input Gain
042F	H6-04	Pulse Train Input Bias
0430	H6-05	Pulse Train Input Filter Time
0431	H6-06	Pulse Train Monitor Terminal MP Selection
0432	H6-07	Pulse Train Monitor Scaling
0480	L1-01	Motor Overload Protection Selection
0481	L1-02	Motor Overload Protection Time
0482	L1-03	Motor Overheat Alarm Operation Selection (PTC input)
0483	L1-04	Motor Overheat Fault Operation Selection (PTC input)
0484	L1-05	Motor Temperature Input Filter Time (PTC input)
046D	L1-13	Continuous Electrothermal Operation Selection
0485	L2-01	Momentary Power Loss Operation Selection
0486	L2-02	Momentary Power Loss Ride-Thru Time
0487	L2-03	Momentary Power Loss Minimum Baseblock Time
0488	L2-04	Momentary Power Loss Voltage Recovery Ramp Time
0489	L2-05	Undervoltage Detection Level (UV)
048A	L2-06	KEB Deceleration Time
048B	L2-07	KEB Acceleration Time
048C	L2-08	KEB Start Output Frequency Reduction
0461	L2-11	Desired DC Bus Voltage during KEB
048F	L3-01	Stall Prevention Selection during Acceleration
0490	L3-02	Stall Prevention Level during Acceleration
0491	L3-03	Stall Prevention Limit during Acceleration
0492	L3-04	Stall Prevention Selection during Deceleration
0493	L3-05	Stall Prevention Selection during Run
0494	L3-06	Stall Prevention Level during Run
04C7	L3-11	OV Suppression Function Selection
0462	L3-17	Overvoltage Suppression and Stall Prevention Desired DC Bus Voltage
0465	L3-20	Main Power Circuit Voltage Adjustment Gain
0466	L3-21	Accel/Decel Rate Calculation Gain
04F9	L3-22	Deceleration Time at Stall Prevention during Acceleration
04FD	L3-23	Automatic Reduction Selection for Stall Prevention during Run
046E	L3-24	Motor Acceleration Time for Inertia Calculations
046F	L3-25	Load Inertia Ratio
0499	L4-01	Speed Agreement Detection Level
049A	L4-02	Speed Agreement Detection Width
049B	L4-03	Speed Agreement Detection Level (+/-)
049C	L4-04	Speed Agreement Detection Width (+/-)
049D	L4-05	Frequency Reference Loss Detection Selection
04C2	L4-06	Frequency Reference at Reference Loss
0470	L4-07	Frequency Detection Conditions
049E	L5-01	Number of Auto Restart Attempts
049F	L5-02	Auto Restart Operation Selection
046C	L5-04	Fault Reset Interval Time
0467	L5-05	Fault Reset Operation Selection
04A1	L6-01	Torque Detection Selection 1
04A2	L6-02	Torque Detection Level 1
04A3	L6-03	Torque Detection Time 1
04A4	L6-04	Torque Detection Selection 2
04A5	L6-05	Torque Detection Level 2
04A6	L6-06	Torque Detection Time 2
0468	L6-08	Mechanical Weakening (OL5) Detection Operation
0469	L6-09	Mechanical Weakening Detection Speed Level
046A	L6-10	Mechanical Weakening Detection Time
046B	L6-11	Mechanical Weakening Detection Start Time
04A7	L7-01	Forward Torque Limit
04A8	L7-02	Reverse Torque Limit
04A9	L7-03	Forward Regenerative Torque Limit
04AA	L7-04	Reverse Regenerative Torque Limit
04AC	L7-06	Torque Limit Integral Time Constant
04C9	L7-07	Torque Limit Control Method Selection during Accel/Decel
04AD	L8-01	Internal Dynamic Braking Resistor Protection Selection (ERF type)
04AE	L8-02	Overheat Alarm Level
04AF	L8-03	Overheat Pre-Alarm Operation Selection
04B1	L8-05	Input Phase Loss Protection Selection
04B3	L8-07	Output Phase Loss Protection
04B5	L8-09	Output Ground Fault Detection Selection
04B6	L8-10	Heatsink Cooling Fan Operation Selection
04B7	L8-11	Heatsink Cooling Fan Operation Delay Time
04B8	L8-12	Ambient Temperature Setting
04BB	L8-15	OL2 Characteristics Selection at Low Speeds
04BE	L8-18	Soft CLA Selection
04BF	L8-19	Frequency Reduction Rate during OH Pre-Alarm
04DF	L8-29	Current Unbalance Detection (LF2)
04EC	L8-35	Installation Method
04EF	L8-38	Carrier Frequency Reduction
04F1	L8-40	Carrier Frequency Reduction Time
04F2	L8-41	Current Alarm Selection
0580	n1-01	Hunting Prevention Selection
0581	n1-02	Hunting Prevention Gain Setting
0582	n1-03	Hunting Prevention Time Constant
0530	n1-05	Hunting Prevention Gain while in Reverse
0584	n2-01	Speed Feedback Detection Control (AFR) Gain
0585	n2-02	Speed Feedback Detection Control (AFR) Time Constant
0586	n2-03	Speed Feedback Detection Control (AFR) Time Constant 2
0588	n3-01	High-Slip Braking Deceleration Frequency Width
0589	n3-02	High-Slip Braking Current Limit
058A	n3-03	High-Slip Braking Dwell Time at Stop
058B	n3-04	High-Slip Braking Overload Time
0531	n3-13	Overexcitation Deceleration Gain
0579	n3-21	High-Slip Suppression Current Level
057B	n3-23	Overexcitation driving selection
0570	n6-01	Line-to-Line Motor Resistance Online Tuning
0538	n8-45	Speed Feedback Detection Control Gain
053A	n8-47	Pull-In Current Compensation Time Constant
053B	n8-48	Pull-In Current
053C	n8-49	Load Current
053E	n8-51	Acceleration Pull-In Current
056D	n8-54	Voltage Error compensation time constant
056E	n8-55	Load Inertia
057D	n8-62	Output voltage limit
0500	o1-01	Drive Mode Unit Monitor Selection
0501	o1-02	User Monitor Selection After Power Up
0502	o1-03	Digital Operator Display Selection
0520	o1-10	Frequency Reference Setting and User-Set Display
0521	o1-11	Frequency Reference Setting / Decimal Display
0505	o2-01	LOCAL/REMOTE Key Function Selection
0506	o2-02	STOP Key Function Selection
0507	o2-03	User Parameter Default Value
0508	o2-04	Drive/kVA Selection
0509	o2-05	Frequency Reference Setting Method Selection
050A	o2-06	Operation Selection when Digital Operator is Disconnected
0527	o2-07	Motor Direction at Power Up when Using Operator
050B	o4-01	Accumulated Operation Time Setting
050C	o4-02	Accumulated Operation Time Selection
050E	o4-03	Cooling Fan Operation Time Setting
051D	o4-05	Capacitor Maintenance Setting
0523	o4-07	Inrush Prevention Relay Maintenance Setting
0525	o4-09	IGBT Maintenance Setting
0510	o4-11	U2, U3 Initialize Selection
0512	o4-12	kWh Monitor Initialize Selection
0528	o4-13	Number of Run Commands Initialize Selection
1840	r1-01	DWEZ Connection Parameter 1 (upper)
1841	r1-02	DWEZ Connection Parameter 1 (lower)
1842	r1-03	DWEZ Connection Parameter 2 (upper)
1843	r1-04	DWEZ Connection Parameter 2 (lower)
1844	r1-05	DWEZ Connection Parameter 3 (upper)
1845	r1-06	DWEZ Connection Parameter 3 (lower)
1846	r1-07	DWEZ Connection Parameter 4 (upper)
1847	r1-08	DWEZ Connection Parameter 4 (lower)
1848	r1-09	DWEZ Connection Parameter 5 (upper)
1849	r1-10	DWEZ Connection Parameter 5 (lower)
184A	r1-11	DWEZ Connection Parameter 6 (upper)
184B	r1-12	DWEZ Connection Parameter 6 (lower)
184C	r1-13	DWEZ Connection Parameter 7 (upper)
184D	r1-14	DWEZ Connection Parameter 7 (lower)
184E	r1-15	DWEZ Connection Parameter 8 (upper)
184F	r1-16	DWEZ Connection Parameter 8 (lower)
1850	r1-17	DWEZ Connection Parameter 9 (upper)
1851	r1-18	DWEZ Connection Parameter 9 (lower)
1852	r1-19	DWEZ Connection Parameter 10 (upper)
1853	r1-20	DWEZ Connection Parameter 10 (lower)
1854	r1-21	DWEZ Connection Parameter 11 (upper)
1855	r1-22	DWEZ Connection Parameter 11 (lower)
1856	r1-23	DWEZ Connection Parameter 12 (upper)
1857	r1-24	DWEZ Connection Parameter 12 (lower)
1858	r1-25	DWEZ Connection Parameter 13 (upper)
1859	r1-26	DWEZ Connection Parameter 13 (lower)
185A	r1-27	DWEZ Connection Parameter 14 (upper)
185B	r1-28	DWEZ Connection Parameter 14 (lower)
185C	r1-29	DWEZ Connection Parameter 15 (upper)
185D	r1-30	DWEZ Connection Parameter 15 (lower)
185E	r1-31	DWEZ Connection Parameter 16 (upper)
185F	r1-32	DWEZ Connection Parameter 16 (lower)
1860	r1-33	DWEZ Connection Parameter 17 (upper)
1861	r1-34	DWEZ Connection Parameter 17 (lower)
1862	r1-35	DWEZ Connection Parameter 18 (upper)
1863	r1-36	DWEZ Connection Parameter 18 (lower)
1864	r1-37	DWEZ Connection Parameter 19 (upper)
1865	r1-38	DWEZ Connection Parameter 19 (lower)
1866	r1-39	DWEZ Connection Parameter 20 (upper)
1867	r1-40	DWEZ Connection Parameter 20 (lower)
0700	T1-00	Motor Selection 1/2
0701	T1-01	Auto-Tuning Mode Selection
0702	T1-02	Motor Rated Power
0703	T1-03	Motor Rated Voltage
0704	T1-04	Motor Rated Current
0705	T1-05	Motor Base Frequency
0706	T1-06	Number of Motor Poles
0707	T1-07	Motor Base Speed
070B	T1-11	Motor Iron Loss
0040	U1-01	Frequency Reference
0041	U1-02	Output Frequency
0042	U1-03	Output Current
0043	U1-04	Control Mode
0044	U1-05	Motor Speed
0045	U1-06	Output Voltage Reference
0046	U1-07	DC Bus Voltage
0047	U1-08	Output Power
0048	U1-09	Torque Reference
0049	U1-10	Input Terminal Status
004A	U1-11	Output Terminal Status
004B	U1-12	Drive Status
004E	U1-13	Terminal A1 Input Voltage
004F	U1-14	Terminal A2 Input Voltage
0053	U1-16	Output Frequency after Soft Start
0061	U1-18	OPE Fault Parameter
0066	U1-19	MEMOBUS/Modbus Error Code
007D	U1-24	Input Pulse Monitor
004D	U1-25	Software No. (Flash)
005B	U1-26	Software No. (ROM)
0080	U2-01	Current Fault
0081	U2-02	Previous Fault
0082	U2-03	Frequency Reference at Previous Fault
0083	U2-04	Output Frequency at Previous Fault
0084	U2-05	Output Current at Previous Fault
0085	U2-06	Motor Speed at Previous Fault
0086	U2-07	Output Voltage at Previous Fault
0087	U2-08	DC Bus Voltage at Previous Fault
0088	U2-09	Output Power at Previous Fault
0089	U2-10	Torque Reference at Previous Fault
008A	U2-11	Input Terminal Status at Previous Fault
008B	U2-12	Output Terminal Status at Previous Fault
008C	U2-13	Drive Operation Status at Previous Fault
008D	U2-14	Cumulative Operation Time at Previous Fault
07E0	U2-15	Soft Starter Speed Reference at Previous Fault
07E1	U2-16	Motor q-Axis Current at Previous Fault
07E2	U2-17	Motor d-Axis Current at Previous Fault
0090	U3-01	Most Recent Fault
0091	U3-02	2nd Most Recent Fault
0092	U3-03	3rd Most Recent Fault
0093	U3-04	4th Most Recent Fault
0094	U3-11	Cumulative Operation Time at Most Recent Fault
0095	U3-12	Cumulative Operation Time at 2nd Most Recent Fault
0096	U3-13	Cumulative Operation Time at 3rd Most Recent Fault
0097	U3-14	Cumulative Operation Time at 4th Most Recent Fault
0800	U3-01	Most Recent Fault
0801	U3-02	2nd Most Recent Fault
0802	U3-03	3rd Most Recent Fault
0803	U3-04	4th Most Recent Fault
0804	U3-05	5th Most Recent Fault
0805	U3-06	6th Most Recent Fault
0806	U3-07	7th Most Recent Fault
0807	U3-08	8th Most Recent Fault
0808	U3-09	9th Most Recent Fault
0809	U3-10	10th Most Recent Fault
080A	U3-11	Cumulative Operation Time at Most Recent Fault
080B	U3-12	Cumulative Operation Time at 2nd Most Recent Fault
080C	U3-13	Cumulative Operation Time at 3rd Most Recent Fault
080D	U3-14	Cumulative Operation Time at 4th Most Recent Fault
080E	U3-15	Cumulative Operation Time at 5th Most Recent Fault
080F	U3-16	Cumulative Operation Time at 6th Most Recent Fault
0810	U3-17	Cumulative Operation Time at 7th Most Recent Fault
0811	U3-18	Cumulative Operation Time at 8th Most Recent Fault
0812	U3-19	Cumulative Operation Time at 9th Most Recent Fault
0813	U3-20	Cumulative Operation Time at 10th Most Recent Fault
004C	U4-01	Accumulated Operation Time
0075	U4-02	Number of Run Commands
0067	U4-03	Cooling Fan Operation Time
007E	U4-04	Cooling maintenance
007C	U4-05	Capacitor Maintenance
07D6	U4-06	Rushing into prevention relay maintenance
07D7	U4-07	IGBT Maintenance
0068	U4-08	Heatsink Temperature
005E	U4-09	LED Check
005C	U4-10	kWH, Lower 4 Digits
005D	U4-11	kWH, Upper 5 Digits
07CF	U4-13	Peak Hold Current
07D0	U4-14	Peak Hold Output Frequency
07D8	U4-16	Motor Overload Estimate (OL1)
07DA	U4-18	Frequency Reference Source Selection
07DB	U4-19	Frequency Reference from MEMOBUS/Modbus Comm.
07DC	U4-20	Option Frequency Reference
07DD	U4-21	Run Command Source Selection
07DE	U4-22	MEMOBUS/Modbus Communications Reference
07DF	U4-23	Option Card Reference
0057	U5-01	PID Feedback
0063	U5-02	PID Input
0064	U5-03	PID Output
0065	U5-04	PID Setpoint
07D2	U5-05	PID differential feedback
07D3	U5-06	PID Adjusted Feedback
0051	U6-01	Motor Secondary Current (Iq)
0052	U6-02	Motor Excitation Current (ld)
0055	U6-04	ASR Output
0059	U6-05	Output voltage reference (Vq)
005A	U6-06	Output Voltage Reference (Vd)
005F	U6-07	q-axis ACR Output
0060	U6-08	d-Axis ACR Output
07D4	U6-20	Frequency Reference Bias (Up/Down 2)
07D5	U6-21	Offset Frequency
1950	U8-01	DriveWorksEZ custom monitor 1
1951	U8-02	DriveWorksEZ custom monitor 2
1952	U8-03	DriveWorksEZ custom monitor 3
1953	U8-04	DriveWorksEZ custom monitor 4
1954	U8-05	DriveWorksEZ custom monitor 5
1955	U8-06	DriveWorksEZ custom monitor 6
1956	U8-07	DriveWorksEZ custom monitor 7
1957	U8-08	DriveWorksEZ custom monitor 8
1958	U8-09	DriveWorksEZ custom monitor 9
1959	U8-10	DriveWorksEZ custom monitor 10
[SigDataEnd]

[SigData]-B
0001.0	H5-12 = 0: Forward Run Command (0 = Stop, 1 = Run) H5-12 = 1: Run Command (0 = Stop, 1 = Forward Run)
0001.1	H5-12 = 0: Reverse Run Command (0 = Stop, 1 = Run) H5-12 = 1: Forward/Reverse (0 = Stop, 1 = Reverse Run)
0001.2	External fault 1: Error (EFO)
0001.3	Fault reset 1: Reset command
0001.4	Multi-function input command 1
0001.5	Multi-function input command 2
0001.6	Multi-function input command 3
0001.7	Multi-function input command 4
0001.8	Multi-function input command 5
0001.9	Multi-function input command 6
0001.A	Multi-function input command 7
0002	Frequency Reference
0003	V/f gain
0006	PID Target (0.01% signed)
0007	Analog output 1 setting (10 V/4000 H)
0008	Analog output 2 setting (10 V/4000 H)
0009.0	Contact output (Terminal MA/MB-MC) 1: ON 0: OFF
0009.1	Photocoupling output1 (Terminal P1-PC) 1：ON　0：OFF
0009.2	Photocoupling output2 (Terminal P2-PC) 1：ON　0：OFF
0009.6	Fault Contact Output Enabled (1 = enabled by bit 7)
0009.7	Error contact (terminal MA/MB-MC) 1: ON 0: OFF
000F.1	PID Target Input
000F.C	Broadcast data terminal S5 input 1: Enabled 0: Disabled
000F.D	Broadcast data terminal S6 input 1: Enabled 0: Disabled
000F.E	Broadcast data terminal S7 input 1: Enabled 0: Disabled
0020.0	Operation 1: Operating 0: Stopped
0020.1	Reverse operation 1: Reverse operation 0: Forward operation
0020.2	Inverter startup complete 1: Completed 2: Not completed
0020.3	Error 1: Error
0020.4	Data setting error 1: Error
0020.5	Multi-function contact output (Terminal MA/MB-MC) 1: ON 0: OFF
0020.6	Multi-function Photocoupling output1 (Terminal P1-PC) 1：ON　0：OFF
0020.7	Multi-function Photocoupling output2 (Terminal P2-PC) 1：ON　0：OFF
0020.E	ComRef status
0020.F	ComCtrl status
0021.0	Overcurrent (oC) Ground fault (GF)
0021.1	oV: DC Bus Overvoltage
0021.2	oL2: Drive Overload
0021.3	oH1, oH2: Overheat Fault
0021.4	rH, rr: Braking Resistor Fault
0021.6	FbL, FbH: PID Feedback Fault
0021.7	EF0 to 7: External Fault
0021.8	Hardware Fault (includes OFx)
0021.9	oL1, oL3, oL4, UL3, UL4: Motor Overload/Overtorque 1 or 2, Undertorque 1 or 2
0021.A	PGo, oS, dEv: PG Disconnect, Overspeed, Speed Deviation
0021.B	Uv1: DC Bus Undervoltage
0021.C	Uv1, Uv2, Uv3: DC Bus Undervoltage, Control Power Supply Fault, Inrush Prevention Circuit Fault
0021.D	PF, LF: Input/Output Phase Loss
0021.E	CE, bUS: Communication Loss
0021.F	oPr: Operator Disconnected
0022.0	1: Writing data
0022.3	1: Upper and lower limit errors
0022.4	1: Data integrity error
0022.5	1: EEPROM Writing data
0023	Frequency reference (U1-01)
0024	Output frequency (U1-02)
0025	Output voltage reference (U1-06) (Unit: 1/0.1V)
0026	Output current (U1-03) (Unit: 10/1A)
0027	Output power (U1-08)
0028	Torque reference (U1-09)
0029.0	SC: Load Short Circuit
0029.1	GF: Ground Fault
0029.2	PF: DC Bus Voltage Fault
0029.3	LF: Output Phase Loss
0029.4	rH: Braking Resistor Overheat
002A.2	EF: Simultaneous Forward and Reverse Run Commands
002A.3	bb: Drive Baseblock
002A.4	oL3: Overtorque 1
002A.5	oH: Heatsink Overheat
002A.6	oV: DC Bus Overvoltage
002A.7	Uv: DC Bus Undervoltage
002A.9	CE: Communications Error
002A.A	bUS: Option Error
002A.B	UL3: Undertorque 1
002A.C	oH2: Drive Overheat Prealarm
002A.D	FbL, FbH: PID Feeback Alarm
002A.F	CALL: Waiting for Communications
002B.0	1: Control circuit terminal S1 Closed
002B.1	1: Control circuit terminal S2 Closed
002B.2	1: Control circuit terminal S3 Closed
002B.3	1: Control circuit terminal S4 Closed
002B.4	1: Control circuit terminal S5 Closed
002B.5	1: Control circuit terminal S6 Closed
002B.6	1: Control circuit terminal S7 Closed
002C.0	Operation 1: Operating
002C.1	Zero-speed 1: Zero-speed
002C.2	Frequency matching 1: Matched
002C.3	User-defined speed matching 1: Matched
002C.4	Frequency detection 1　1: Output frequency≦L4-01 
002C.5	Frequency detection 2　1: Output frequency≧L4-01 
002C.6	Drive Ready 1: Drive Ready
002C.7	Low voltage detection 1: Detected
002C.8	Baseblock 1: Inverter output baseblock
002C.9	Frequency reference mode 1: Not communications 0: Communications
002C.A	Run Command mode 1: Not communications 0: Communications
002C.B	Over/Undertorque 1, 2
002C.C	Frequency reference lost 1: Lost
002C.D	Retrying error 1: Retrying
002C.E	Error 1:Error occurred
002C.F	MEMOBUS communications time-out 1: Timed out
002D.0	Multi-function contact output (terminal MA/MB-MC) 1: ON 0: OFF
002D.1	Multi-function PHC output1 (terminal P1-PC) 1: ON 0: OFF
002D.2	Multi-function PHC output2 (terminal P2-PC) 1: ON 0: OFF
002D.3	Abnormal contact (Terminal MA/MB-MC)　1:ON　0:OFF
002F	Frequency Reference Bias (UP2, DOWN2) 1000/100%
0031	DC Bus Voltage (U1-07)
0032	Torque monitor (Unit: 1/1%)
0034	Production code1 [ASCII]VO
0035	Production code2 [ASCII]AO
0038	PID Feedback (100% / max. output frequency; 1/0.1% resolution; not signed)
0039	PID Input (100% / max. output frequency; 1/0.1% resolution; signed)
003A	PID Output (100% / max. output frequency; 1/0.1% resolution; signed)
003D.0	CRC error
003D.1	Data Length Error
003D.3	Parity error
003D.4	Overrun error
003D.5	Framing error
003D.6	Timeout
0101	A1-01	Access Level Selection
0102	A1-02	Control Method Selection
0103	A1-03	Initialize Parameters
0104	A1-04	Password 1
0105	A1-05	Password 2
0127	A1-06	Application Preset
0128	A1-07	DriveWorksEZ function selection
0106	A2-01	User Parameters 1
0107	A2-02	User Parameters 2
0108	A2-03	User Parameters 3
0109	A2-04	User Parameters 4
010A	A2-05	User Parameters 5
010B	A2-06	User Parameters 6
010C	A2-07	User Parameters 7
010D	A2-08	User Parameters 8
010E	A2-09	User Parameters 9
010F	A2-10	User Parameters 10
0110	A2-11	User Parameters 11
0111	A2-12	User Parameters 12
0112	A2-13	User Parameters 13
0113	A2-14	User Parameters 14
0114	A2-15	User Parameters 15
0115	A2-16	User Parameters 16
0116	A2-17	User Parameters 17
0117	A2-18	User Parameters 18
0118	A2-19	User Parameters 19
0119	A2-20	User Parameters 20
011A	A2-21	User Parameters 21
011B	A2-22	User Parameters 22
011C	A2-23	User Parameters 23
011D	A2-24	User Parameters 24
011E	A2-25	User Parameters 25
011F	A2-26	User Parameters 26
0120	A2-27	User Parameters 27
0121	A2-28	User Parameters 28
0122	A2-29	User Parameters 29
0123	A2-30	User Parameters 30
0124	A2-31	User Parameters 31
0125	A2-32	User Parameters 32
0126	A2-33	User Parameter Automatic Selection
0180	b1-01	Frequency Reference Selection 1
0181	b1-02	Run Command Selection 1
0182	b1-03	Stopping Method Selection
0183	b1-04	Reverse Operation Selection
0186	b1-07	Local/Remote Run Selection
0187	b1-08	Run Command Selection while in Programming Mode
01C3	b1-14	Phase Order Selection
01C4	b1-15	Frequency Reference 2
01C5	b1-16	Run Command Source 2
01C6	b1-17	Run Command at Power Up
0189	b2-01	DC Injection Braking Start Frequency
018A	b2-02	DC Injection Braking Current
018B	b2-03	DC Injection Braking Time/DC Excitation Time at Start
018C	b2-04	DC Injection Braking Time at Stop
0190	b2-08	Magnetic Flux Compensation Capacity
01BA	b2-12	Short Circuit Brake Time at Start
01BB	b2-13	Short Circuit Brake Time at Stop
0191	b3-01	Speed Search Selection
0192	b3-02	Speed Search Deactivation Current
0193	b3-03	Speed Search Deceleration Time
0195	b3-05	Speed Search Delay Time
0196	b3-06	Output Current 1 during Speed Search
019A	b3-10	Speed Search Detection Compensation Gain
019E	b3-14	Bi-Directional Speed Search Selection
01F0	b3-17	Speed Search Restart Current Level
01F1	b3-18	Speed Search Restart Detection Time
01F2	b3-19	Number of Speed Search Restarts
01C0	b3-24	Speed Search Method Selection
01C8	b3-25	Speed Search Retry Interval Time
01A3	b4-01	Timer Function On-Delay Time
01A4	b4-02	Timer Function Off-Delay Time
01A5	b5-01	PID Function Setting
01A6	b5-02	Proportional Gain Setting (P)
01A7	b5-03	Integral Time Setting (I)
01A8	b5-04	Integral Limit Setting
01A9	b5-05	Derivative Time (D)
01AA	b5-06	PID Output Limit
01AB	b5-07	PID Offset Adjustment
01AC	b5-08	PID Primary Delay Time Constant
01AD	b5-09	PID Output Level Selection
01AE	b5-10	PID Output Gain Setting
01AF	b5-11	PID Output Reverse Selection
01B0	b5-12	PID Feedback Reference Missing Detection Selection
01B1	b5-13	PID Feedback Loss Detection Level
01B2	b5-14	PID Feedback Loss Detection Time
01B3	b5-15	PID Sleep Function Start Level
01B4	b5-16	PID Sleep Delay Time
01B5	b5-17	PID Accel/Decel Time
01DC	b5-18	PID Setpoint Selection
01DD	b5-19	PID Setpoint Value
01E2	b5-20	PID Setpoint Scaling
019F	b5-34	PID Output Lower Limit
01A0	b5-35	PID Input Limit
01A1	b5-36	PID Feedback High Detection Level
01A2	b5-37	PID Feedback High Level Detection Time
01FE	b5-38	PID Setpoint / User Display
01FF	b5-39	PID Setpoint Display Digits
01B6	b6-01	Dwell Reference at Start
01B7	b6-02	Dwell Time at Start
01B8	b6-03	Dwell Frequency at Stop
01B9	b6-04	Dwell Time at Stop
01CC	b8-01	Energy Saving Control Selection
01CD	b8-02	Energy Saving Gain
01CE	b8-03	Energy Saving Control Filter Time Constant
01CF	b8-04	Energy Saving Coefficient Value
01D0	b8-05	Power Detection Filter Time
01D1	b8-06	Search Operation Voltage Limit
0200	C1-01	Acceleration Time 1
0201	C1-02	Deceleration Time 1
0202	C1-03	Acceleration Time 2
0203	C1-04	Deceleration Time 2
0204	C1-05	Acceleration Time 3 (Motor 2 Accel Time 1)
0205	C1-06	Deceleration Time 3 (Motor 2 Decel Time 1)
0206	C1-07	Acceleration Time 4 (Motor 2 Accel Time 2)
0207	C1-08	Deceleration Time 4 (Motor 2 Decel Time 2)
0208	C1-09	Fast-Stop Time
0209	C1-10	Accel/Decel Time Setting Units
020A	C1-11	Accel/Decel Time Switching Frequency
020B	C2-01	S-Curve Characteristic at Accel Start
020C	C2-02	S-Curve Characteristic at Accel End
020D	C2-03	S-Curve Characteristic at Decel Start
020E	C2-04	S-Curve Characteristic at Decel End
020F	C3-01	Slip Compensation Gain
0210	C3-02	Slip Compensation Primary Delay Time
0211	C3-03	Slip Compensation Limit
0212	C3-04	Slip Compensation Selection during Regeneration
0213	C3-05	Output Voltage Limit Operation Selection
0215	C4-01	Torque Compensation Gain
0216	C4-02	Torque Compensation Primary Delay Time
0217	C4-03	Torque Compensation at Forward Start
0218	C4-04	Torque Compensation at Reverse Start
0219	C4-05	Torque Compensation Time Constant
021A	C4-06	Torque Compensation Primary Delay Time 2
021B	C5-01	ASR Proportional Gain 1
021C	C5-02	ASR Integral Time 1
021D	C5-03	ASR Proportional Gain 2
021E	C5-04	ASR Integral Time 2
021F	C5-05	ASR Limit
0223	C6-01	Normal/Heavy Duty Selection
0224	C6-02	Carrier Frequency Selection
0225	C6-03	Carrier Frequency Upper Limit
0226	C6-04	Carrier Frequency Lower Limit
0227	C6-05	Carrier Frequency Proportional Gain
0280	d1-01	Frequency Reference 1
0281	d1-02	Frequency Reference 2
0282	d1-03	Frequency Reference 3
0283	d1-04	Frequency Reference 4
0284	d1-05	Frequency Reference 5
0285	d1-06	Frequency Reference 6
0286	d1-07	Frequency Reference 7
0287	d1-08	Frequency Reference 8
0288	d1-09	Frequency Reference 9
028B	d1-10	Frequency Reference 10
028C	d1-11	Frequency Reference 11
028D	d1-12	Frequency Reference 12
028E	d1-13	Frequency Reference 13
028F	d1-14	Frequency Reference 14
0290	d1-15	Frequency Reference 15
0291	d1-16	Frequency Reference 16
0292	d1-17	Jog Frequency Reference
0289	d2-01	Frequency Reference Upper Limit
028A	d2-02	Frequency Reference Lower Limit
0293	d2-03	Master Speed Reference Lower Limit
0294	d3-01	Jump Frequency 1
0295	d3-02	Jump Frequency 2
0296	d3-03	Jump Frequency 3
0297	d3-04	Jump Frequency width
0298	d4-01	Frequency Reference Hold Function Selection
02AA	d4-03	Frequency Reference Bias Step (Up/Down 2)
02AB	d4-04	Frequency Reference Accel/Decel (Up/Down 2)
02AC	d4-05	Frequency Reference Bias Operation Mode Selection (Up/Down 2)
02AD	d4-06	Frequency Reference Bias (Up/Down 2)
02AE	d4-07	Analog Frequency Reference Fluctuation Limit (Up/Down 2)
02AF	d4-08	Frequency Reference Bias Upper Limit (Up/Down 2)
02B0	d4-09	Frequency Reference Bias Lower Limit (Up/Down 2)
02B6	d4-10	Up/Down Frequency Reference Limit Selection
02B8	d4-12	Stop Position Gain
02B2	d7-01	Offset Frequency 1
02B3	d7-02	Offset Frequency 2
02B4	d7-03	Offset Frequency 3
0300	E1-01	Input Voltage Setting
0302	E1-03	V/f Pattern Selection
0303	E1-04	Max Output Frequency
0304	E1-05	Max Output Voltage
0305	E1-06	Base Frequency
0306	E1-07	Mid Output Frequency
0307	E1-08	Mid Output Frequency Voltage
0308	E1-09	Minimum Output Freq.
0309	E1-10	Minimum Output Freq. Voltage
030A	E1-11	Mid Output Frequency 2
030B	E1-12	Mid Output Frequency Voltage 2
030C	E1-13	Base Voltage
030E	E2-01	Motor Rated Current
030F	E2-02	Motor Rated Slip
0310	E2-03	Motor No-Load Current
0311	E2-04	Number of Motor Poles
0312	E2-05	Motor Line-to-Line Resistance
0313	E2-06	Motor Leakage Inductance
0314	E2-07	Motor Iron-Core Saturation Coefficient 1
0315	E2-08	Motor Iron-Core Saturation Coefficient 2
0316	E2-09	Motor Mechanical Loss
0317	E2-10	Motor Iron Loss for Torque Compensation
0318	E2-11	Motor Rated Output
0328	E2-12	Motor Iron-Core Saturation Coefficient 3
0319	E3-01	Motor 2 Control Method
031A	E3-04	Motor 2 Max Output Frequency
031B	E3-05	Motor 2 Max Voltage
031C	E3-06	Motor 2 Base Frequency
031D	E3-07	Motor 2 Mid Output Freq.
031E	E3-08	Motor 2 Mid Output Freq. Voltage
031F	E3-09	Motor 2 Min. Output Freq.
0320	E3-10	Motor 2 Min. Output Freq. Voltage
0345	E3-11	Motor 2 Mid Output Frequency 2
0346	E3-12	Motor 2 Mid Output Frequency Voltage 2
0347	E3-13	Motor 2 Base Voltage
0321	E4-01	Motor 2 Rated Current
0322	E4-02	Motor 2 Rated Slip
0323	E4-03	Motor 2 Rated No-Load Current
0324	E4-04	Motor 2 Motor Poles
0325	E4-05	Motor 2 Line-to-Line Resistance
0326	E4-06	Motor 2 Leakage Inductance
0343	E4-07	Motor 2 Motor Iron-Core Saturation Coefficient 1
0344	E4-08	Motor 2 Motor Iron-Core Saturation Coefficient 2
033F	E4-09	Motor 2 Mechanical Loss
0340	E4-10	Motor 2 Iron Loss
0327	E4-11	Motor 2 Rated Capacity
0342	E4-12	Motor 2 Iron-Core Saturation Coefficient 3
033E	E4-14	Motor 2 Slip Compensation Gain
0341	E4-15	Torque Compensation Gain - Motor 2
0329	E5-01	Motor Code Selection (for PM motor)
032A	E5-02	Motor Rated Capacity (for PM motor)
032B	E5-03	Motor Rated Current
032C	E5-04	Motor Poles
032D	E5-05	Motor Resistance
032E	E5-06	Motor d Axis Inductance
032F	E5-07	Motor q Axis Inductance
0331	E5-09	Motor Induction Voltage Constant 1
0353	E5-24	Motor Induction Voltage Parameter 2
0381	F1-02	Operation Selection at PG Open Circuit (PGO)
0382	F1-03	Operation Selection at Overspeed (OS)
0383	F1-04	Operation Selection at Deviation
0387	F1-08	Overspeed Detection Level
0388	F1-09	Overspeed Detection Delay Time
0389	F1-10	Excessive Speed Deviation Detection Level
038A	F1-11	Excessive Speed Deviation Detection Delay Time
038D	F1-14	PG Open-Circuit Detection Time
03A2	F6-01	Communications Error operation Selection
03A3	F6-02	External fault from comm. Option selection
03A4	F6-03	External fault from comm. Option operation selection
03E5	F6-04	Trace Sampling Rate
03E6	F6-10	CC-Link Node Address
03E7	F6-11	CC-Link communications speed
03BB	F6-14	BUS Error auto reset
03C1	F6-20	DeviceNet MAC Address
03C2	F6-21	Device Net Communications Speed
03C3	F6-22	Device Net PCA setting
03C4	F6-23	Device Net PPA setting
03C5	F6-24	Device Net Idle mode fault detection
03CB	F6-30	Profibus node address
03CC	F6-31	Profibus Clear mode selection
03CD	F6-32	Profibus Map selections
03D0	F6-36	CANopen Node ID selection
03D1	F6-37	CANopen Communications speed
03D5	F6-40	CompoNet Node ID
03D6	F6-41	CompoNet Speed
03E5	F7-01	Ethernet IP Address 1
03E6	F7-02	Ethernet IP Address 1
03E7	F7-03	Ethernet IP Address 1
03E8	F7-04	Ethernet IP Address 1
03E9	F7-05	Subnet Mask 1
03EA	F7-06	Subnet Mask 2
03EB	F7-07	Subnet Mask 3
03EC	F7-08	Subnet Mask 4
03ED	F7-09	Gateway Address 1
03EE	F7-10	Gateway Address 2
03EF	F7-11	Gateway Address 3
03F0	F7-12	Gateway Address 4
03F1	F7-13	Dress Mode at Startup
03F2	F7-14	Security password
03F3	F7-15	Duplex Mode Selection
03F6	F7-18	Communication Speed Selection
03F7	F7-19	Web Page Access
03F8	F7-20	Gateway selection
03F9	F7-21	Communication loss time out
0438	H1-01	Multi-Function Digital Input Terminal S1 Function Selection
0439	H1-02	Multi-Function Digital Input Terminal S2 Function Selection
0400	H1-03	Multi-Function Digital Input Terminal S3 Function Selection
0401	H1-04	Multi-Function Digital Input Terminal S4 Function Selection
0402	H1-05	Multi-Function Digital Input Terminal S5 Function Selection
0403	H1-06	Multi-Function Digital Input Terminal S6 Function Selection
0404	H1-07	Multi-Function Digital Input Terminal S7 Function Selection
040B	H2-01	Terminal MA, MB and MC Function Selection (relay)
040C	H2-02	Terminal P1 Function Selection
040D	H2-03	Terminal P2 Function Selection
0437	H2-06	Watt Hour Output Unit Selection
0410	H3-01	Terminal A1 Signal Level Selection
0434	H3-02	Terminal A1 Function Selection
0411	H3-03	Terminal A1 Gain Setting
0412	H3-04	Terminal A1 Bias Setting
0417	H3-09	Terminal A2 Signal Level Selection
0418	H3-10	Terminal A2 Function Selection
0419	H3-11	Terminal A2 Gain Setting
041A	H3-12	Terminal A2 Input Bias
041B	H3-13	Analog Input Filter Time Constant
041D	H4-01	Multi-Function Analog Output Terminal AM
041E	H4-02	Multi-Function Analog Output Terminal AM Gain
041F	H4-03	Multi-Function Analog Output Terminal AM Gain
0425	H5-01	Drive Node Address
0426	H5-02	Communication Speed Selection
0427	H5-03	Communication Parity Selection
0428	H5-04	Stopping Method After Communication Error
0429	H5-05	Communication Fault Detection Selection
042A	H5-06	Drive Transmit Wait Time
042B	H5-07	RTS Control Selection
0435	H5-09	CE Detection Time
0436	H5-10	Unit Selection for MEMOBUS/Modbus Register 0025H
043C	H5-11	Communications ENTER Function Selection
043D	H5-12	Run Command Method Selection
042C	H6-01	Pulse Train Input Terminal RP Function Selection
042D	H6-02	Pulse Train Input Scaling
042E	H6-03	Pulse Train Input Gain
042F	H6-04	Pulse Train Input Bias
0430	H6-05	Pulse Train Input Filter Time
0431	H6-06	Pulse Train Monitor Terminal MP Selection
0432	H6-07	Pulse Train Monitor Scaling
0480	L1-01	Motor Overload Protection Selection
0481	L1-02	Motor Overload Protection Time
0482	L1-03	Motor Overheat Alarm Operation Selection (PTC input)
0483	L1-04	Motor Overheat Fault Operation Selection (PTC input)
0484	L1-05	Motor Temperature Input Filter Time (PTC input)
046D	L1-13	Continuous Electrothermal Operation Selection
0485	L2-01	Momentary Power Loss Operation Selection
0486	L2-02	Momentary Power Loss Ride-Thru Time
0487	L2-03	Momentary Power Loss Minimum Baseblock Time
0488	L2-04	Momentary Power Loss Voltage Recovery Ramp Time
0489	L2-05	Undervoltage Detection Level (UV)
048A	L2-06	KEB Deceleration Time
048B	L2-07	KEB Acceleration Time
048C	L2-08	KEB Start Output Frequency Reduction
0461	L2-11	Desired DC Bus Voltage during KEB
048F	L3-01	Stall Prevention Selection during Acceleration
0490	L3-02	Stall Prevention Level during Acceleration
0491	L3-03	Stall Prevention Limit during Acceleration
0492	L3-04	Stall Prevention Selection during Deceleration
0493	L3-05	Stall Prevention Selection during Run
0494	L3-06	Stall Prevention Level during Run
04C7	L3-11	OV Suppression Function Selection
0462	L3-17	Overvoltage Suppression and Stall Prevention Desired DC Bus Voltage
0465	L3-20	Main Power Circuit Voltage Adjustment Gain
0466	L3-21	Accel/Decel Rate Calculation Gain
04F9	L3-22	Deceleration Time at Stall Prevention during Acceleration
04FD	L3-23	Automatic Reduction Selection for Stall Prevention during Run
046E	L3-24	Motor Acceleration Time for Inertia Calculations
046F	L3-25	Load Inertia Ratio
0499	L4-01	Speed Agreement Detection Level
049A	L4-02	Speed Agreement Detection Width
049B	L4-03	Speed Agreement Detection Level (+/-)
049C	L4-04	Speed Agreement Detection Width (+/-)
049D	L4-05	Frequency Reference Loss Detection Selection
04C2	L4-06	Frequency Reference at Reference Loss
0470	L4-07	Frequency Detection Conditions
049E	L5-01	Number of Auto Restart Attempts
049F	L5-02	Auto Restart Operation Selection
046C	L5-04	Fault Reset Interval Time
0467	L5-05	Fault Reset Operation Selection
04A1	L6-01	Torque Detection Selection 1
04A2	L6-02	Torque Detection Level 1
04A3	L6-03	Torque Detection Time 1
04A4	L6-04	Torque Detection Selection 2
04A5	L6-05	Torque Detection Level 2
04A6	L6-06	Torque Detection Time 2
0468	L6-08	Mechanical Weakening (OL5) Detection Operation
0469	L6-09	Mechanical Weakening Detection Speed Level
046A	L6-10	Mechanical Weakening Detection Time
046B	L6-11	Mechanical Weakening Detection Start Time
04A7	L7-01	Forward Torque Limit
04A8	L7-02	Reverse Torque Limit
04A9	L7-03	Forward Regenerative Torque Limit
04AA	L7-04	Reverse Regenerative Torque Limit
04AC	L7-06	Torque Limit Integral Time Constant
04C9	L7-07	Torque Limit Control Method Selection during Accel/Decel
04AD	L8-01	Internal Dynamic Braking Resistor Protection Selection (ERF type)
04AE	L8-02	Overheat Alarm Level
04AF	L8-03	Overheat Pre-Alarm Operation Selection
04B1	L8-05	Input Phase Loss Protection Selection
04B3	L8-07	Output Phase Loss Protection
04B5	L8-09	Output Ground Fault Detection Selection
04B6	L8-10	Heatsink Cooling Fan Operation Selection
04B7	L8-11	Heatsink Cooling Fan Operation Delay Time
04B8	L8-12	Ambient Temperature Setting
04BB	L8-15	OL2 Characteristics Selection at Low Speeds
04BE	L8-18	Soft CLA Selection
04BF	L8-19	Frequency Reduction Rate during OH Pre-Alarm
04DF	L8-29	Current Unbalance Detection (LF2)
04EC	L8-35	Installation Method
04EF	L8-38	Carrier Frequency Reduction
04F1	L8-40	Carrier Frequency Reduction Time
04F2	L8-41	Current Alarm Selection
0580	n1-01	Hunting Prevention Selection
0581	n1-02	Hunting Prevention Gain Setting
0582	n1-03	Hunting Prevention Time Constant
0530	n1-05	Hunting Prevention Gain while in Reverse
0584	n2-01	Speed Feedback Detection Control (AFR) Gain
0585	n2-02	Speed Feedback Detection Control (AFR) Time Constant
0586	n2-03	Speed Feedback Detection Control (AFR) Time Constant 2
0588	n3-01	High-Slip Braking Deceleration Frequency Width
0589	n3-02	High-Slip Braking Current Limit
058A	n3-03	High-Slip Braking Dwell Time at Stop
058B	n3-04	High-Slip Braking Overload Time
0531	n3-13	Overexcitation Deceleration Gain
0579	n3-21	High-Slip Suppression Current Level
057B	n3-23	Overexcitation driving selection
0570	n6-01	Line-to-Line Motor Resistance Online Tuning
0538	n8-45	Speed Feedback Detection Control Gain
053A	n8-47	Pull-In Current Compensation Time Constant
053B	n8-48	Pull-In Current
053C	n8-49	Load Current
053E	n8-51	Acceleration Pull-In Current
056D	n8-54	Voltage Error compensation time constant
056E	n8-55	Load Inertia
057D	n8-62	Output voltage limit
0500	o1-01	Drive Mode Unit Monitor Selection
0501	o1-02	User Monitor Selection After Power Up
0502	o1-03	Digital Operator Display Selection
0520	o1-10	Frequency Reference Setting and User-Set Display
0521	o1-11	Frequency Reference Setting / Decimal Display
0505	o2-01	LOCAL/REMOTE Key Function Selection
0506	o2-02	STOP Key Function Selection
0507	o2-03	User Parameter Default Value
0508	o2-04	Drive/kVA Selection
0509	o2-05	Frequency Reference Setting Method Selection
050A	o2-06	Operation Selection when Digital Operator is Disconnected
0527	o2-07	Motor Direction at Power Up when Using Operator
050B	o4-01	Accumulated Operation Time Setting
050C	o4-02	Accumulated Operation Time Selection
050E	o4-03	Cooling Fan Operation Time Setting
051D	o4-05	Capacitor Maintenance Setting
0523	o4-07	Inrush Prevention Relay Maintenance Setting
0525	o4-09	IGBT Maintenance Setting
0510	o4-11	U2, U3 Initialize Selection
0512	o4-12	kWh Monitor Initialize Selection
0528	o4-13	Number of Run Commands Initialize Selection
1840	r1-01	DWEZ Connection Parameter 1 (upper)
1841	r1-02	DWEZ Connection Parameter 1 (lower)
1842	r1-03	DWEZ Connection Parameter 2 (upper)
1843	r1-04	DWEZ Connection Parameter 2 (lower)
1844	r1-05	DWEZ Connection Parameter 3 (upper)
1845	r1-06	DWEZ Connection Parameter 3 (lower)
1846	r1-07	DWEZ Connection Parameter 4 (upper)
1847	r1-08	DWEZ Connection Parameter 4 (lower)
1848	r1-09	DWEZ Connection Parameter 5 (upper)
1849	r1-10	DWEZ Connection Parameter 5 (lower)
184A	r1-11	DWEZ Connection Parameter 6 (upper)
184B	r1-12	DWEZ Connection Parameter 6 (lower)
184C	r1-13	DWEZ Connection Parameter 7 (upper)
184D	r1-14	DWEZ Connection Parameter 7 (lower)
184E	r1-15	DWEZ Connection Parameter 8 (upper)
184F	r1-16	DWEZ Connection Parameter 8 (lower)
1850	r1-17	DWEZ Connection Parameter 9 (upper)
1851	r1-18	DWEZ Connection Parameter 9 (lower)
1852	r1-19	DWEZ Connection Parameter 10 (upper)
1853	r1-20	DWEZ Connection Parameter 10 (lower)
1854	r1-21	DWEZ Connection Parameter 11 (upper)
1855	r1-22	DWEZ Connection Parameter 11 (lower)
1856	r1-23	DWEZ Connection Parameter 12 (upper)
1857	r1-24	DWEZ Connection Parameter 12 (lower)
1858	r1-25	DWEZ Connection Parameter 13 (upper)
1859	r1-26	DWEZ Connection Parameter 13 (lower)
185A	r1-27	DWEZ Connection Parameter 14 (upper)
185B	r1-28	DWEZ Connection Parameter 14 (lower)
185C	r1-29	DWEZ Connection Parameter 15 (upper)
185D	r1-30	DWEZ Connection Parameter 15 (lower)
185E	r1-31	DWEZ Connection Parameter 16 (upper)
185F	r1-32	DWEZ Connection Parameter 16 (lower)
1860	r1-33	DWEZ Connection Parameter 17 (upper)
1861	r1-34	DWEZ Connection Parameter 17 (lower)
1862	r1-35	DWEZ Connection Parameter 18 (upper)
1863	r1-36	DWEZ Connection Parameter 18 (lower)
1864	r1-37	DWEZ Connection Parameter 19 (upper)
1865	r1-38	DWEZ Connection Parameter 19 (lower)
1866	r1-39	DWEZ Connection Parameter 20 (upper)
1867	r1-40	DWEZ Connection Parameter 20 (lower)
0700	T1-00	Motor Selection 1/2
0701	T1-01	Auto-Tuning Mode Selection
0702	T1-02	Motor Rated Power
0703	T1-03	Motor Rated Voltage
0704	T1-04	Motor Rated Current
0705	T1-05	Motor Base Frequency
0706	T1-06	Number of Motor Poles
0707	T1-07	Motor Base Speed
070B	T1-11	Motor Iron Loss
0040	U1-01	Frequency Reference
0041	U1-02	Output Frequency
0042	U1-03	Output Current
0043	U1-04	Control Mode
0044	U1-05	Motor Speed
0045	U1-06	Output Voltage Reference
0046	U1-07	DC Bus Voltage
0047	U1-08	Output Power
0048	U1-09	Torque Reference
0049.0	U1-10	1: FWD run command (terminal S1 enabled)
0049.1	U1-10	1: REV run command (terminal S2 enabled)
0049.2	U1-10	1: Multi-Function Digital Input 1 (terminal S3 enabled)
0049.3	U1-10	1: Multi-Function Digital Input 2 (terminal S4 enabled)
0049.4	U1-10	1: Multi-Function Digital Input 3 (terminal S5 enabled)
0049.5	U1-10	1: Multi-Function Digital Input 4 (terminal S6 enabled)
0049.6	U1-10	1: Multi-Function Digital Input 5 (terminal S7 enabled)
004A.0	U1-11	1: Multi-Function Digital Output (fault) (terminal MA/MB-MC)
004A.1	U1-11	1: Multi-Function Digital Output 1 (terminal P1) enabled
004A.2	U1-11	1: Multi-Function Digital Output 2 (terminal P2) enabled
004B.0	U1-12	1: During run
004B.1	U1-12	1: During zero-speed
004B.2	U1-12	1: During REV
004B.3	U1-12	1: During fault reset signal input
004B.4	U1-12	1: During speed agree
004B.5	U1-12	1: Drive ready
004B.6	U1-12	1: During alarm detection
004B.7	U1-12	1: During fault detection
004E	U1-13	Terminal A1 Input Voltage
004F	U1-14	Terminal A2 Input Voltage
0053	U1-16	Output Frequency after Soft Start
0061	U1-18	OPE Fault Parameter
0066.0	U1-19	1:CRC error 
0066.1	U1-19	1:Data length error
0066.3	U1-19	1:Parity error
0066.4	U1-19	1:Overrun error
0066.5	U1-19	1:Framing error
0066.6	U1-19	1:Timeout
007D	U1-24	Input Pulse Monitor
004D	U1-25	Software No. (Flash)
005B	U1-26	Software No. (ROM)
0080	U2-01	Current Fault
0081	U2-02	Previous Fault
0082	U2-03	Frequency Reference at Previous Fault
0083	U2-04	Output Frequency at Previous Fault
0084	U2-05	Output Current at Previous Fault
0085	U2-06	Motor Speed at Previous Fault
0086	U2-07	Output Voltage at Previous Fault
0087	U2-08	DC Bus Voltage at Previous Fault
0088	U2-09	Output Power at Previous Fault
0089	U2-10	Torque Reference at Previous Fault
008A	U2-11	Input Terminal Status at Previous Fault
008B	U2-12	Output Terminal Status at Previous Fault
008C	U2-13	Drive Operation Status at Previous Fault
008D	U2-14	Cumulative Operation Time at Previous Fault
07E0	U2-15	Soft Starter Speed Reference at Previous Fault
07E1	U2-16	Motor q-Axis Current at Previous Fault
07E2	U2-17	Motor d-Axis Current at Previous Fault
0090	U3-01	Most Recent Fault
0091	U3-02	2nd Most Recent Fault
0092	U3-03	3rd Most Recent Fault
0093	U3-04	4th Most Recent Fault
0094	U3-11	Cumulative Operation Time at Most Recent Fault
0095	U3-12	Cumulative Operation Time at 2nd Most Recent Fault
0096	U3-13	Cumulative Operation Time at 3rd Most Recent Fault
0097	U3-14	Cumulative Operation Time at 4th Most Recent Fault
0800	U3-01	Most Recent Fault
0801	U3-02	2nd Most Recent Fault
0802	U3-03	3rd Most Recent Fault
0803	U3-04	4th Most Recent Fault
0804	U3-05	5th Most Recent Fault
0805	U3-06	6th Most Recent Fault
0806	U3-07	7th Most Recent Fault
0807	U3-08	8th Most Recent Fault
0808	U3-09	9th Most Recent Fault
0809	U3-10	10th Most Recent Fault
080A	U3-11	Cumulative Operation Time at Most Recent Fault
080B	U3-12	Cumulative Operation Time at 2nd Most Recent Fault
080C	U3-13	Cumulative Operation Time at 3rd Most Recent Fault
080D	U3-14	Cumulative Operation Time at 4th Most Recent Fault
080E	U3-15	Cumulative Operation Time at 5th Most Recent Fault
080F	U3-16	Cumulative Operation Time at 6th Most Recent Fault
0810	U3-17	Cumulative Operation Time at 7th Most Recent Fault
0811	U3-18	Cumulative Operation Time at 8th Most Recent Fault
0812	U3-19	Cumulative Operation Time at 9th Most Recent Fault
0813	U3-20	Cumulative Operation Time at 10th Most Recent Fault
004C	U4-01	Accumulated Operation Time
0075	U4-02	Number of Run Commands
0067	U4-03	Cooling Fan Operation Time
007E	U4-04	Cooling maintenance
007C	U4-05	Capacitor Maintenance
07D6	U4-06	Rushing into prevention relay maintenance
07D7	U4-07	IGBT Maintenance
0068	U4-08	Heatsink Temperature
005E	U4-09	LED Check
005C	U4-10	kWH, Lower 4 Digits
005D	U4-11	kWH, Upper 5 Digits
07CF	U4-13	Peak Hold Current
07D0	U4-14	Peak Hold Output Frequency
07D8	U4-16	Motor Overload Estimate (OL1)
07DA	U4-18	Frequency Reference Source Selection
07DB	U4-19	Frequency Reference from MEMOBUS/Modbus Comm.
07DC	U4-20	Option Frequency Reference
07DD	U4-21	Run Command Source Selection
07DE	U4-22	MEMOBUS/Modbus Communications Reference
07DF	U4-23	Option Card Reference
0057	U5-01	PID Feedback
0063	U5-02	PID Input
0064	U5-03	PID Output
0065	U5-04	PID Setpoint
07D2	U5-05	PID differential feedback
07D3	U5-06	PID Adjusted Feedback
0051	U6-01	Motor Secondary Current (Iq)
0052	U6-02	Motor Excitation Current (ld)
0055	U6-04	ASR Output
0059	U6-05	Output voltage reference (Vq)
005A	U6-06	Output Voltage Reference (Vd)
005F	U6-07	q-axis ACR Output
0060	U6-08	d-Axis ACR Output
07D4	U6-20	Frequency Reference Bias (Up/Down 2)
07D5	U6-21	Offset Frequency
1950	U8-01	DriveWorksEZ custom monitor 1
1951	U8-02	DriveWorksEZ custom monitor 2
1952	U8-03	DriveWorksEZ custom monitor 3
1953	U8-04	DriveWorksEZ custom monitor 4
1954	U8-05	DriveWorksEZ custom monitor 5
1955	U8-06	DriveWorksEZ custom monitor 6
1956	U8-07	DriveWorksEZ custom monitor 7
1957	U8-08	DriveWorksEZ custom monitor 8
1958	U8-09	DriveWorksEZ custom monitor 9
1959	U8-10	DriveWorksEZ custom monitor 10
[SigDataEnd]-B