Name=PLC1
UP150
MaxSigCnt=0
DataFormat=Dec

[D-SigData]
D0001	STATUS (Input Error) [Operating data]
D0002	PV (Measured input value) [Operating data]
D0003	CSP (Currently used target Setpoint) [Operating data]
D0004	OUT (Control output) [Operating data]
D0008	SEGTIME [Operating data]
D0010	SEGNO (Program segment number selection) [Operating data]
D0011	MODE (Operating mode) [Operating data]
D0103	CTL (Control mode) [Operating parameter]
D0104	AT (Auto-tuning) [Operating parameter]
D0105	P (Proportional band) [Operating parameter]
D0106	I (Integral time) [Operating parameter]
D0107	D (Derivative time) [Operating parameter]
D0108	MR (Manual reset) [Operating parameter]
D0111	HYS (Hysteresis for on/off control) [Operating parameter]
D0112	CT (Control output cycle time) [Operating parameter]
D0116	FL (PV input filter) [Operating parameter]
D0117	BS (PV input bias) [Operating parameter]
D0118	LOC (Key lock) [Operating parameter]
D0121	RUN/RESET [Operating parameter]
D0122	HOLD (Program hold) [Operating parameter]
D0123	ADV (Segment advance) [Operating parameter]
D0207	SC (SUPER function) [Setup parameter]
D0208	DR (Direct/reverse action) [Setup parameter]
D0210	PSL (Protocol selection) [Setup parameter]
D0211	ADR (Controller address) [Setup parameter]
D0212	BPS (Baud rate) [Setup parameter]
D0213	PRI (Parity) [Setup parameter]
D0214	STP (Stop bit) [Setup parameter]
D0215	DLN (Data length) [Setup parameter]
D0216	EV1 (Event 1 type) [Program parameter]
D0217	AL1 (PV event 1 type) [Program parameter]
D0218	A1 (PV event 1 setpoint) [Program parameter]
D0219	HY1 (PV event 1 hysterisis)  [Program parameter]
D0220	EON1 (Time event 1 on time) [Program parameter]
D0221	EOF1 (Time event 1 off time) [Program parameter]
D0222	EV2 (Event 2 type) [Program parameter]
D0223	AL2 (PV event 2 type) [Program parameter]
D0224	A2 (PV event 2 setpoint) [Program parameter]
D0225	HY2 (PV event 2 hysterisis) [Program parameter]
D0226	EON2 (Time event 2 on time) [Program parameter]
D0227	EOF2 (Time event 2 off time) [Program parameter]
D0228	SSP (Starting target setpoint) [Program parameter]
D0229	SP1 (Target setpoint 1) [Program parameter]
D0230	TM1 (Segment time 1) [Program parameter]
D0231	SP2 (Target setpoint 2) [Program parameter]
D0232	TM2 (Segment time 2) [Program parameter]
D0233	SP3 (Target setpoint 3) [Program parameter]
D0234	TM3 (Segment time 3) [Program parameter]
D0235	SP4 (Target setpoint 4) [Program parameter]
D0236	TM4 (Segment time 4) [Program parameter]
D0237	SP5 (Target setpoint 5) [Program parameter]
D0238	TM5 (Segment time 5) [Program parameter]
D0239	SP6 (Target setpoint 6) [Program parameter]
D0240	TM6 (Segment time 6) [Program parameter]
D0241	SP7 (Target setpoint 7) [Program parameter]
D0242	TM7 (Segment time 7) [Program parameter]
D0243	SP8 (Target setpoint 8) [Program parameter]
D0244	TM8 (Segment time 8) [Program parameter]
D0245	SP9 (Target setpoint 9) [Program parameter]
D0246	TM9 (Segment time 9) [Program parameter]
D0247	SP10 (Target setpoint 10) [Program parameter]
D0248	TM10 (Segment time 10) [Program parameter]
D0249	SP11 (Target setpoint 11) [Program parameter]
D0250	TM11 (Segment time 11) [Program parameter]
D0251	SP12 (Target setpoint 12) [Program parameter]
D0252	TM12 (Segment time 12) [Program parameter]
D0253	SP13 (Target setpoint 13) [Program parameter]
D0254	TM13 (Segment time 13) [Program parameter]
D0255	SP14 (Target setpoint 14) [Program parameter]
D0256	TM14 (Segment time 14) [Program parameter]
D0257	SP15 (Target setpoint 15) [Program parameter]
D0258	TM15 (Segment time 15) [Program parameter]
D0259	SP16 (Target setpoint 16) [Program parameter]
D0260	TM16 (Segment time 16) [Program parameter]
D0261	JC (Junction code) [Program parameter]
D0262	WTZ (Wait zone) [Program parameter]
D0263	STC (Start code) [Program parameter]
D0301	IN (Measured input type) [Setup parameter]
D0302	DP (Decimal point position of measured input) [Setup parameter]
D0303	RH (Maximum value of measured input scale) [Setup parameter]
D0304	RL (Minimum value of measured input scale) [Setup parameter]
D0305	SPH (Maximum value of program setting range) [Setup parameter]
D0306	SPL (Minimum value of program setting range) [Setup parameter]
D0307	TMU (Program time unit) [Setup parameter]
D0311	RTL (Minimum value of retransmission output) [Setup parameter]
D0312	RTH (Maximum value of retransmission output) [Setup parameter]
[D-SigDataEnd]

[D-SigData]-B
D0001.00    EV1.st (‘1’ if event 1 is on, or ‘0’ if off) [Operating data]
D0001.01    EV2.st (‘1’ if event 2 is on, or ‘0’ if off) [Operating data]
D0001.04    PV+over.st (PV above the upper limit of scale) [Operating data]
D0001.05    PV-over.st (PV below the lower limit of scale) [Operating data]
D0001.06    BO.st (Burn-out error) [Operating data]
D0001.08    SYSTEM.E.st (Error in system data) [Operating data]
D0001.09    CALB.E.st (Error in calibrated values) [Operating data]
D0001.10    PARA.E.st (Error in operating parameters) [Operating data]
D0001.12    ADERR.st (Error in A/D Converter) [Operating data]
D0001.13    RJCERR.st (RJC error in PV) [Operating data]
D0001.14    EEP.E.st (Error in EEPROM) [Operating data]
D0002	    PV (Measured input value) [Operating data]
D0003	    CSP (Currently used target Setpoint) [Operating data]
D0004	    OUT (Control output) [Operating data]
D0008	    SEGTIME [Operating data]
D0010	    SEGNO (Program segment number selection) [Operating data]
D0011.00    RUN.st (‘1’ if program operation is run, or ‘0’ if reset) [Operating data]
D0011.01    RESET.st (‘1’ if program operation is reset, or ‘0’ if run) [Operating data]
D0011.04    HOLD.st (‘1’ if hold operation is on, or ‘0’ if off) [Operating data]
D0011.05    WAIT.st (‘1’ if wait operation is on, or ‘0’ if off) [Operating data]
D0103	    CTL (Control mode) [Operating parameter]
D0104	    AT (Auto-tuning) [Operating parameter]
D0105	    P (Proportional band) [Operating parameter]
D0106	    I (Integral time) [Operating parameter]
D0107	    D (Derivative time) [Operating parameter]
D0108	    MR (Manual reset) [Operating parameter]
D0111	    HYS (Hysteresis for on/off control) [Operating parameter]
D0112	    CT (Control output cycle time) [Operating parameter]
D0116	    FL (PV input filter) [Operating parameter]
D0117	    BS (PV input bias) [Operating parameter]
D0118	    LOC (Key lock) [Operating parameter]
D0121	    RUN/RESET [Operating parameter]
D0122	    HOLD (Program hold) [Operating parameter]
D0123	    ADV (Segment advance) [Operating parameter]
D0207	    SC (SUPER function) [Setup parameter]
D0208	    DR (Direct/reverse action) [Setup parameter]
D0210	    PSL (Protocol selection) [Setup parameter]
D0211	    ADR (Controller address) [Setup parameter]
D0212	    BPS (Baud rate) [Setup parameter]
D0213	    PRI (Parity) [Setup parameter]
D0214	    STP (Stop bit) [Setup parameter]
D0215	    DLN (Data length) [Setup parameter]
D0216	    EV1 (Event 1 type) [Program parameter]
D0217	    AL1 (PV event 1 type) [Program parameter]
D0218	    A1 (PV event 1 setpoint) [Program parameter]
D0219	    HY1 (PV event 1 hysterisis)  [Program parameter]
D0220	    EON1 (Time event 1 on time) [Program parameter]
D0221	    EOF1 (Time event 1 off time) [Program parameter]
D0222	    EV2 (Event 2 type) [Program parameter]
D0223	    AL2 (PV event 2 type) [Program parameter]
D0224	    A2 (PV event 2 setpoint) [Program parameter]
D0225	    HY2 (PV event 2 hysterisis) [Program parameter]
D0226	    EON2 (Time event 2 on time) [Program parameter]
D0227	    EOF2 (Time event 2 off time) [Program parameter]
D0228	    SSP (Starting target setpoint) [Program parameter]
D0229	    SP1 (Target setpoint 1) [Program parameter]
D0230	    TM1 (Segment time 1) [Program parameter]
D0231	    SP2 (Target setpoint 2) [Program parameter]
D0232	    TM2 (Segment time 2) [Program parameter]
D0233	    SP3 (Target setpoint 3) [Program parameter]
D0234	    TM3 (Segment time 3) [Program parameter]
D0235	    SP4 (Target setpoint 4) [Program parameter]
D0236	    TM4 (Segment time 4) [Program parameter]
D0237	    SP5 (Target setpoint 5) [Program parameter]
D0238	    TM5 (Segment time 5) [Program parameter]
D0239	    SP6 (Target setpoint 6) [Program parameter]
D0240	    TM6 (Segment time 6) [Program parameter]
D0241	    SP7 (Target setpoint 7) [Program parameter]
D0242	    TM7 (Segment time 7) [Program parameter]
D0243	    SP8 (Target setpoint 8) [Program parameter]
D0244	    TM8 (Segment time 8) [Program parameter]
D0245	    SP9 (Target setpoint 9) [Program parameter]
D0246	    TM9 (Segment time 9) [Program parameter]
D0247	    SP10 (Target setpoint 10) [Program parameter]
D0248	    TM10 (Segment time 10) [Program parameter]
D0249	    SP11 (Target setpoint 11) [Program parameter]
D0250	    TM11 (Segment time 11) [Program parameter]
D0251	    SP12 (Target setpoint 12) [Program parameter]
D0252	    TM12 (Segment time 12) [Program parameter]
D0253	    SP13 (Target setpoint 13) [Program parameter]
D0254	    TM13 (Segment time 13) [Program parameter]
D0255	    SP14 (Target setpoint 14) [Program parameter]
D0256	    TM14 (Segment time 14) [Program parameter]
D0257	    SP15 (Target setpoint 15) [Program parameter]
D0258	    TM15 (Segment time 15) [Program parameter]
D0259	    SP16 (Target setpoint 16) [Program parameter]
D0260	    TM16 (Segment time 16) [Program parameter]
D0261	    JC (Junction code) [Program parameter]
D0262	    WTZ (Wait zone) [Program parameter]
D0263	    STC (Start code) [Program parameter]
D0301	    IN (Measured input type) [Setup parameter]
D0302	    DP (Decimal point position of measured input) [Setup parameter]
D0303	    RH (Maximum value of measured input scale) [Setup parameter]
D0304	    RL (Minimum value of measured input scale) [Setup parameter]
D0305	    SPH (Maximum value of program setting range) [Setup parameter]
D0306	    SPL (Minimum value of program setting range) [Setup parameter]
D0307	    TMU (Program time unit) [Setup parameter]
D0311	    RTL (Minimum value of retransmission output) [Setup parameter]
D0312	    RTH (Maximum value of retransmission output) [Setup parameter]
[D-SigDataEnd]-B

[I-SigData]
I0001	Error information (same as data in the D0001 register) [On-off statuses]
I0017	User area (Data can be written to or read from the range of I relays) [Read/Write]
I0033	User area (Data can be written to or read from the range of I relays) [Read/Write]
I0049	UR32 (Operation mode (same as D0011)) [On-off statues]
[I-SigDataEnd]

[I-SigData]-B
I0001	EV1.st (‘1’ if event 1 is on, or ‘0’ if off) [On-off statuses]
I0002	EV2.st (‘1’ if event 2 is on, or ‘0’ if off) [On-off statuses]
I0005	PV+over.st (PV above the upper limit of scale) [On-off statuses]
I0006	PV-over.st (PV below the lower limit of scale) [On-off statuses]
I0007	BO.st (Burn-out error) [On-off statuses]
I0009	SYSTEM.E.st Error in system data [On-off statuses]
I0010	CALB.E.st Error in calibrated values [On-off statuses]
I0011	PARA.E.st Error in operating parameters [On-off statuses]
I0013	ADERR.st Error in A/D Converter [On-off statuses]
I0014	RJCERR.st RJC error in PV [On-off statuses]
I0015	EEP.E.st Error in EEPROM [On-off statuses]
I0017	UR1 [Read/Write]
I0018	UR2 [Read/Write]
I0019	UR3 [Read/Write]
I0020	UR4 [Read/Write]
I0021	UR5 [Read/Write]
I0022	UR6 [Read/Write]
I0023	UR7 [Read/Write]
I0024	UR8 [Read/Write]
I0025	UR9 [Read/Write]
I0026	UR10 [Read/Write]
I0027	UR11 [Read/Write]
I0028	UR12 [Read/Write]
I0029	UR13 [Read/Write]
I0030	UR14 [Read/Write]
I0031	UR15 [Read/Write]
I0032	UR16 [Read/Write]
I0033	UR17 [Read/Write]
I0034	UR18 [Read/Write]
I0035	UR19 [Read/Write]
I0036	UR20 [Read/Write]
I0037	UR21 [Read/Write]
I0038	UR22 [Read/Write]
I0039	UR23 [Read/Write]
I0040	UR24 [Read/Write]
I0041	UR25 [Read/Write]
I0042	UR26 [Read/Write]
I0043	UR27 [Read/Write]
I0044	UR28 [Read/Write]
I0045	UR29 [Read/Write]
I0046	UR30 [Read/Write]
I0047	UR31 [Read/Write]
I0048	UR32 [Read/Write]
I0049	RUN [On-off statues]
I0050	RESET [On-off statues]
I0053	HOLD [On-off statues]
I0054	WAIT [On-off statues]
[I-SigDataEnd]-B