Name=PLC1
UT130/UT150/UT152/UT155
MaxSigCnt=0
DataFormat=Dec

[D-SigData]
D0001	STATUS (Input Error) [Operating data]
D0002	PV (Measured input value) [Operating data]
D0003	CSP (Currently used target Setpoint) [Operating data]
D0004	OUT (Control output) [Operating data]
D0005	HOUT (Heating-side control output) [Operating data]
D0006	COUT (Cooling-side control output) [Operating data]
D0007	HC (Heater current measured value) [Operating data]
D0008	T1 (Timer setting 1) [Operating data]
D0009	T2 (Timer setting 2) [Operating data]
D0010	SPNO (Target setpoint number selection) [Operating data]
D0101	A1 (Alarm or Timer Setpoints) [Operating parameter] 
D0102	A2 (Alarm or Timer Setpoints) [Operating parameter]
D0103	CTL (Control mode) [Operating parameter]
D0104	AT (Auto-tuning) [Operating parameter]
D0105	P (Proportional band) [Operating parameter]
D0106	I (Integral time) [Operating parameter]
D0107	D (Derivative time) [Operating parameter]
D0108	MR (Manual reset) [Operating parameter]
D0109	COL (Cooling-side gain) [Operating parameter]
D0110	DB (Dead band) [Operating parameter]
D0111	HYS (Hysteresis for on/off control) [Operating parameter]
D0112	CT (Control output cycle time) [Operating parameter]
D0113	CTC (Cooling-side control output cycle time) [Operating parameter]
D0114	SP1 (Target setpoint 1) [Operating parameter]
D0115	SP2 (Target setpoint 1) [Operating parameter]
D0116	FL (PV input filter) [Operating parameter]
D0117	BS (PV input bias) [Operating parameter]
D0118	LOC (Key lock) [Operating parameter]
D0120	CSP1 (Target Setpoint for Writing via Communication Only) [Operating parameter]
D0201	UPR (Setpoint rampup-rate) [Setup parameter]
D0202	DNR (Setpoint rampdown-rate) [Setup parameter]
D0203	AL1 (Alarm 1 type) [Setup parameter]
D0204	AL2 (Alarm 2 type) [Setup parameter]
D0205	HY1 (Alarm 1 hysteresis) [Setup parameter]
D0206	HY2 (Alarm 2 hysteresis) [Setup parameter]
D0207	SC (SUPER function) [Setup parameter]
D0208	DR (Direct/reverse action) [Setup parameter]
D0209	DSP [Setup parameter]
D0210	PSL (Protocol selection) [Setup parameter]
D0211	ADR (Controller address) [Setup parameter]
D0212	BPS (Baud rate) [Setup parameter]
D0213	PRI (Parity) [Setup parameter]
D0214	STP (Stop bit) [Setup parameter]
D0215	DLN (Data length) [Setup parameter]
D0301	IN (Measured input type) [Setup parameter]
D0302	DP (Decimal point position of measured input) [Setup parameter]
D0303	RH (Maximum value of measured input scale) [Setup parameter]
D0304	RL (Minimum value of measured input scale) [Setup parameter]
D0305	SPH (Maximum value of target setpoint range) [Setup parameter]
D0306	SPL (Minimum value of target setpoint range) [Setup parameter]
D0307	TMU (Setpoint ramprate time unit) [Setup parameter]
D0308	DIS (DI-function selection) [Setup parameter]
D0309	EOT (Output in STOP mode) [Setup parameter]
D0310	TTU (Timer time unit) [Setup parameter]
D0311	RTH (Maximum value of retransmission output) [Setup parameter]
D0312	RTL (Minimum value of retransmission output) [Setup parameter]
[D-SigDataEnd]

[D-SigData]-B
D0001.00    ALM1.st (‘1’ if alarm 1 is on, or ‘0’ if off) [Operating data]
D0001.01    ALM2.st (‘1’ if alarm 2 is on, or ‘0’ if off) [Operating data]
D0001.04    PV+over.st (PV above the upper limit of scale) [Operating data]
D0001.05    PV-over.st (PV below the lower limit of scale) [Operating data]
D0001.06    BO.st (Burn-out error) [Operating data]
D0001.08    SYSTEM.E.st (Error in system data) [Operating data]
D0001.09    CALB.E.st (Error in calibrated values) [Operating data]
D0001.10    PARA.E.st (Error in operating parameters) [Operating data]
D0001.12    ADERR.st (Error in A/D Converter) [Operating data]
D0001.13    RJCERR.st (RJC error in PV) [Operating data]
D0001.14    EEP.E.st (Error in EEPROM) [Operating data]
D0002	    PV (Measured input value) [Operating data]
D0003	    CSP (Currently used target Setpoint) [Operating data]
D0004	    OUT (Control output) [Operating data]
D0005	    HOUT (Heating-side control output) [Operating data]
D0006	    COUT (Cooling-side control output) [Operating data]
D0007	    HC (Heater current measured value) [Operating data]
D0008	    T1 (Timer setting 1) [Operating data]
D0009	    T2 (Timer setting 2) [Operating data]
D0010	    SPNO (Target setpoint number selection) [Operating data]
D0101	    A1 (Alarm or Timer Setpoints) [Operating parameter] 
D0102	    A2 (Alarm or Timer Setpoints) [Operating parameter]
D0103	    CTL (Control mode) [Operating parameter]
D0104	    AT (Auto-tuning) [Operating parameter]
D0105	    P (Proportional band) [Operating parameter]
D0106	    I (Integral time) [Operating parameter]
D0107	    D (Derivative time) [Operating parameter]
D0108	    MR (Manual reset) [Operating parameter]
D0109	    COL (Cooling-side gain) [Operating parameter]
D0110	    DB (Dead band) [Operating parameter]
D0111	    HYS (Hysteresis for on/off control) [Operating parameter]
D0112	    CT (Control output cycle time) [Operating parameter]
D0113	    CTC (Cooling-side control output cycle time) [Operating parameter]
D0114	    SP1 (Target setpoint 1) [Operating parameter]
D0115	    SP2 (Target setpoint 1) [Operating parameter]
D0116	    FL (PV input filter) [Operating parameter]
D0117	    BS (PV input bias) [Operating parameter]
D0118	    LOC (Key lock) [Operating parameter]
D0120	    CSP1 (Target Setpoint for Writing via Communication Only) [Operating parameter]
D0201	    UPR (Setpoint rampup-rate) [Setup parameter]
D0202	    DNR (Setpoint rampdown-rate) [Setup parameter]
D0203	    AL1 (Alarm 1 type) [Setup parameter]
D0204	    AL2 (Alarm 2 type) [Setup parameter]
D0205	    HY1 (Alarm 1 hysteresis) [Setup parameter]
D0206	    HY2 (Alarm 2 hysteresis) [Setup parameter]
D0207	    SC (SUPER function) [Setup parameter]
D0208	    DR (Direct/reverse action) [Setup parameter]
D0209	    DSP [Setup parameter]
D0210	    PSL (Protocol selection) [Setup parameter]
D0211	    ADR (Controller address) [Setup parameter]
D0212	    BPS (Baud rate) [Setup parameter]
D0213	    PRI (Parity) [Setup parameter]
D0214	    STP (Stop bit) [Setup parameter]
D0215	    DLN (Data length) [Setup parameter]
D0301	    IN (Measured input type) [Setup parameter]
D0302	    DP (Decimal point position of measured input) [Setup parameter]
D0303	    RH (Maximum value of measured input scale) [Setup parameter]
D0304	    RL (Minimum value of measured input scale) [Setup parameter]
D0305	    SPH (Maximum value of target setpoint range) [Setup parameter]
D0306	    SPL (Minimum value of target setpoint range) [Setup parameter]
D0307	    TMU (Setpoint ramprate time unit) [Setup parameter]
D0308	    DIS (DI-function selection) [Setup parameter]
D0309	    EOT (Output in STOP mode) [Setup parameter]
D0310	    TTU (Timer time unit) [Setup parameter]
D0311	    RTH (Maximum value of retransmission output) [Setup parameter]
D0312	    RTL (Minimum value of retransmission output) [Setup parameter]
[D-SigDataEnd]-B

[I-SigData]
I0001	Error information (same as data in the D0001 register) [On-off statuses]
I0017	User area (Data can be written to or read from the range of I relays) [Read/Write]
I0033	User area (Data can be written to or read from the range of I relays) [Read/Write]
[I-SigDataEnd]

[I-SigData]-B
I0001	ALM1.st (‘1’ if alarm 1 is on, or ‘0’ if off) [On-off statuses]
I0002	ALM2.st (‘1’ if alarm 2 is on, or ‘0’ if off) [On-off statuses]
I0005	PV+over.st (PV above the upper limit of scale) [On-off statuses]
I0006	PV-over.st (PV below the lower limit of scale) [On-off statuses]
I0007	BO.st (Burn-out error) [On-off statuses]
I0009	SYSTEM.E.st Error in system data [On-off statuses]
I0010	CALB.E.st Error in calibrated values [On-off statuses]
I0011	PARA.E.st Error in operating parameters [On-off statuses]
I0013	ADERR.st Error in A/D Converter [On-off statuses]
I0014	RJCERR.st RJC error in PV [On-off statuses]
I0015	EEP.E.st Error in EEPROM [On-off statuses]
I0017	UR1 [Read/Write]
I0018	UR2 [Read/Write]
I0019	UR3 [Read/Write]
I0020	UR4 [Read/Write]
I0021	UR5 [Read/Write]
I0022	UR6 [Read/Write]
I0023	UR7 [Read/Write]
I0024	UR8 [Read/Write]
I0025	UR9 [Read/Write]
I0026	UR10 [Read/Write]
I0027	UR11 [Read/Write]
I0028	UR12 [Read/Write]
I0029	UR13 [Read/Write]
I0030	UR14 [Read/Write]
I0031	UR15 [Read/Write]
I0032	UR16 [Read/Write]
I0033	UR17 [Read/Write]
I0034	UR18 [Read/Write]
I0035	UR19 [Read/Write]
I0036	UR20 [Read/Write]
I0037	UR21 [Read/Write]
I0038	UR22 [Read/Write]
I0039	UR23 [Read/Write]
I0040	UR24 [Read/Write]
I0041	UR25 [Read/Write]
I0042	UR26 [Read/Write]
I0043	UR27 [Read/Write]
I0044	UR28 [Read/Write]
I0045	UR29 [Read/Write]
I0046	UR30 [Read/Write]
I0047	UR31 [Read/Write]
I0048	UR32 [Read/Write]
[I-SigDataEnd]-B