Name=PLC1 UT320/UT321/UT350/UT351 MaxSigCnt=0 DataFormat=Dec [D-SigData] D0001 ADERROR (Input Error) [Data displayed for operation] D0002 ERROR (PV Error) [Data displayed for operation] D0003 PV (Measured input value) [Data displayed for operation] D0004 CSP (Current target setpoint [SP]) [Data displayed for operation] D0005 OUT (Control output value [OUT]) [Data displayed for operation] D0006 HOUT (Heating-side control output in Heating/Cooling Control) [Data displayed for operation] D0007 COUT (Cooling-side control output in Heating/Cooling Control) [Data displayed for operation] D0008 MOD (Operation mode) [Data displayed for operation] D0009 PIDNO (Current PID number) [Data displayed for operation] D0010 CSPNO (Current target-setpoint number) [Data displayed for operation] D0011 ALM (Alarm Status) [Data displayed for operation] D0027 OR (Moving average of sensor grounding alarm) [Data displayed for operation] D0028 HC1 (Heater burnout current measurement 1) [Data displayed for operation] D0029 HC2 (Heater burnout current measurement 2) [Data displayed for operation] D0035 PARAERR (Error in calibration values and parameters) [Data displayed for operation] D0201 A/M (AUTO/MAN modes) [Operation mode parameters] D0205 S/R (STOP/RUN modes) [Operation mode parameters] D0207 SPNO (SP number) [Operation mode parameters] D0215 C.RSP (Used to set SP.) [Operation mode parameters] D0217 MOUT (Used to set control output value or heating-side control output value in the MAN mode.) [Operation mode parameters] D0218 MOUTc (Used to set cooling-side control output value in the MAN mode.) [Operation mode parameters] D0231 A1: Alarm setpoints for alarm 1 [Alarm setpoint parameters] D0232 A2: Alarm setpoints for alarm 2 [Alarm setpoint parameters] D0233 A3: Alarm setpoints for alarm 3 [Alarm setpoint parameters] D0241 AT: Auto-tuning selection [Computation parameters] D0242 SC: SUPER function selection [Computation parameters] D0243 BS: PV bias [Computation parameters] D0244 FL: PV filter [Computation parameters] D0245 UPR: Setpoint ramp-up rate [Computation parameters] D0246 DNR: Setpoint ramp-down rate [Computation parameters] D0250 ORB: ON/OFF rate detection band [Computation parameters] D0251 ORH: ON/OFF rate high-limit [Computation parameters] D0252 ORL: ON/OFF rate low-limit [Computation parameters] D0254 OH (Output high limit Heating-side output high limit (in heating/cooling control)) [Computation parameters] D0255 OL (Output low limit Cooling-side output high limit (in heating/cooling control)) [Computation parameters] D0256 HYS (Hysteresis) [Computation parameters] D0257 DR (Direct/reverse action switching) [Computation parameters] D0258 HB1 (Heater burnout current setpoint 1) [Computation parameters] D0259 HB2 (Heater burnout current setpoint 2) [Computation parameters] D0301 1.SP: Target setpoint [Group-1 parameters] D0306 1.P: Proportional band [Group-1 parameters] D0307 1.I: Integral time [Group-1 parameters] D0308 1.D: Derivative time [Group-1 parameters] D0311 1.MR: Manual reset [Group-1 parameters] D0314 1.Pc: Cooling-side proportional band [Group-1 parameters] D0315 1.Ic: Cooling-side integral time [Group-1 parameters] D0316 1.Dc: Cooling-side derivative time [Group-1 parameters] D0318 1.DB: Deadband [Group-1 parameters] D0319 1.RP: Zone PID reference point [Group-1 parameters] D0326 2.SP: Target setpoint [Group-2 parameters] D0331 2.P: Proportional band [Group-2 parameters] D0332 2.I: Integral time [Group-2 parameters] D0333 2.D: Derivative time [Group-2 parameters] D0336 2.MR: Manual reset [Group-2 parameters] D0339 2.Pc: Cooling-side proportional band [Group-2 parameters] D0340 2.Ic: Cooling-side integral time [Group-2 parameters] D0341 2.Dc: Cooling-side derivative time [Group-2 parameters] D0343 2.DB: Deadband [Group-2 parameters] D0344 2.RP: Zone PID reference point [Group-2 parameters] D0351 3.SP: Target setpoint [Group-3 parameters] D0356 3.P: Proportional band [Group-3 parameters] D0357 3.I: Integral time [Group-3 parameters] D0358 3.D: Derivative time [Group-3 parameters] D0361 3.MR: Manual reset [Group-3 parameters] D0364 3.Pc: Cooling-side proportional band [Group-3 parameters] D0365 3.Ic: Cooling-side integral time [Group-3 parameters] D0366 3.Dc: Cooling-side derivative time [Group-3 parameters] D0368 3.DB: Deadband [Group-3 parameters] D0376 4.SP: Target setpoint [Group-4 parameters] D0381 4.P: Proportional band [Group-4 parameters] D0382 4.I: Integral time [Group-4 parameters] D0383 4.D: Derivative time [Group-4 parameters] D0386 4.MR: Manual reset [Group-4 parameters] D0389 4.Pc: Cooling-side proportional band [Group-4 parameters] D0390 4.Ic: Cooling-side integral time [Group-4 parameters] D0391 4.Dc: Cooling-side derivative time [Group-4 parameters] D0393 4.DB: Deadband [Group-4 parameters] D0494 RDV: zone PID reference deviation. [PID switching parameter] D0904 TMU (Time unit for ramp-rate setting) [Time unit for ramp-rate setting] D0915 AL1 (Alarm-1 type) [Alarm setting parameters] D0916 AL2 (Alarm-2 type) [Alarm setting parameters] D0917 AL3 (Alarm-3 type) [Alarm setting parameters] D0919 HY1 (Alarm-1 hysteresis) [Alarm hysteresis] D0920 HY2 (Alarm-2 hysteresis) [Alarm hysteresis] D0921 HY3 (Alarm-3 hysteresis) [Alarm hysteresis] D0924 PO (Preset output/Heating-side B150 preset output (in heating/cooling control)) [Control function setting parameters] D0925 POc (Cooling-side preset output) [Control function setting parameters] D0927 C.MD (PID control mode) [Control function setting parameters] D0928 AR (Anti-reset windup (Excess integration prevention)) [Control function setting parameters] D0929 ZON (Zone PID selection) [Control function setting parameters] D0932 DIS (DI function selection) [Control function setting parameters] D0933 SPH (Upper limits of target setpoint) [Upper and lower limits of target setpoint] D0934 SPL (Lower limits of target setpoint) [Upper and lower limits of target setpoint] D0935 DY1 (Alarm-1 delay timer) [Alarm-ON delay time] D0936 DY2 (Alarm-2 delay timer) [Alarm-ON delay time] D0937 DY3 (Alarm-3 delay timer) [Alarm-ON delay time] D1013 RET (Retransmission output type) [Retransmission output setting parameters] D1014 RTH (Max. value of retransmission output scale) [Retransmission output setting parameters] D1015 RTL (Min. value of retransmission output scale) [Retransmission output setting parameters] D1036 LOCK [Menu-lock setting parameters] D1101 C.S1 (SELECT display-1registration) [SELECT display registration parameters] D1102 C.S2 (SELECT display-2 registration) [SELECT display registration parameters] D1103 C.S3 (SELECT display-3 registration) [SELECT display registration parameters] D1104 C.S4 (SELECT display-4 registration) [SELECT display registration parameters] D1201 IN (PV input type) [PV input parameters] D1202 UNI (PV input unit) [PV input parameters] D1204 RH (Max. value of PV input range) [PV input parameters] D1205 RL (PV input parameters) [PV input parameters] D1206 SDP (PV input parameters) [PV input parameters] D1207 SH (PV input parameters) [PV input parameters] D1208 SL (Min. value of PV input range) [PV input parameters] D1209 BSL (Selection of PV input burnout action) [PV input parameters] D1210 RJC (Presence/absence of PV input reference junction compensation) [PV input parameters] D1238 OT (Control output type) [Control output parameters] D1240 CT (Control output cycle time Heating-side control output cycle time (in heating/cooling control)) [Control output parameters] D1242 CTc (Cooling-side control output cycle time) [Control output parameters] D1247 PSL (Protocol selection) [RS-485 communication parameters] D1248 BPS (Baud rate) [RS-485 communication parameters] D1249 PRI (Parity) [RS-485 communication parameters] D1250 STP (Stop bit) [RS-485 communication parameters] D1251 DLN (Data length) [RS-485 communication parameters] D1252 ADR (Address) [RS-485 communication parameters] D1253 RP.T (Minimum response time) [RS-485 communication parameters] [D-SigDataEnd] [D-SigData]-B D0001.00 ADERR.st (Input A/D converter error) [Data displayed for operation] D0002.01 PVBO.st (PV burnout error) [Data displayed for operation] D0002.02 RJCERR.st (PV RJC error) [Data displayed for operation] D0002.04 PV+over.st (PV over-scale) [Data displayed for operation] D0002.05 PV-over.st (PV under-scale) [Data displayed for operation] D0002.14 ATERR.st (Auto-tuning error) [Data displayed for operation] D0003 PV (Measured input value) [Data displayed for operation] D0004 CSP (Current target setpoint [SP]) [Data displayed for operation] D0005 OUT (Control output value [OUT]) [Data displayed for operation] D0006 HOUT (Heating-side control output in Heating/Cooling Control) [Data displayed for operation] D0007 COUT (Cooling-side control output in Heating/Cooling Control) [Data displayed for operation] D0008.00 A/M.st (0: AUTO; 1: MAN) [Data displayed for operation] D0008.02 S/R.st (0: RUN; 1: STOP) [Data displayed for operation] D0008.14 AT.st (0: Auto-tuning is OFF; 1: Auto-tuning is ON) [Data displayed for operation] D0009.00 PIDNO.0 (Bit 0 of the current PID number) [Data displayed for operation] D0009.01 PIDNO.1 (Bit 1 of the current PID number) [Data displayed for operation] D0009.02 PIDNO.2 (Bit 2 of the current PID number) [Data displayed for operation] D0009.03 PIDNO.3 (Bit 3 of the current PID number) [Data displayed for operation] D0010.00 CSPNO1.0 (Bit 0 of CSP (current SP number) [Data displayed for operation] D0010.01 CSPNO1.1 (Bit 1 of CSP (current SP number) [Data displayed for operation] D0010.02 CSPNO1.2 (Bit 2 of CSP (current SP number) [Data displayed for operation] D0010.03 CSPNO1.3 (Bit 3 of CSP (current SP number) [Data displayed for operation] D0011.00 ALM1.st (‘1’when alarm 1 is ON; ‘0’when OFF) [Data displayed for operation] D0011.01 ALM2.st (‘1’when alarm 2 is ON; ‘0’when OFF) [Data displayed for operation] D0011.02 ALM3.st (‘1’when alarm 3 is ON; ‘0’when OFF) [Data displayed for operation] D0027 OR (Moving average of sensor grounding alarm) [Data displayed for operation] D0028 HC1 (Heater burnout current measurement 1) [Data displayed for operation] D0029 HC2 (Heater burnout current measurement 2) [Data displayed for operation] D0035.00 CALB.E.st (Calibration value error) [Data displayed for operation] D0035.06 SETUP.st (Setup parameter error) [Data displayed for operation] D0035.08 PARA.E.st (Operating parameter error) [Data displayed for operation] D0035.09 MODE.E.st (Error in power-failure backup data) [Data displayed for operation] D0035.12 EEP.E.st (EEPROM error) [Data displayed for operation] D0035.14 SYSTEM.E.st (System data error) [Data displayed for operation] D0201 A/M (AUTO/MAN modes) [Operation mode parameters] D0205 S/R (STOP/RUN modes) [Operation mode parameters] D0207 SPNO (SP number) [Operation mode parameters] D0215 C.RSP (Used to set SP.) [Operation mode parameters] D0217 MOUT (Used to set control output value or heating-side control output value in the MAN mode.) [Operation mode parameters] D0218 MOUTc (Used to set cooling-side control output value in the MAN mode.) [Operation mode parameters] D0231 A1: Alarm setpoints for alarm 1 [Alarm setpoint parameters] D0232 A2: Alarm setpoints for alarm 2 [Alarm setpoint parameters] D0233 A3: Alarm setpoints for alarm 3 [Alarm setpoint parameters] D0241 AT: Auto-tuning selection [Computation parameters] D0242 SC: SUPER function selection [Computation parameters] D0243 BS: PV bias [Computation parameters] D0244 FL: PV filter [Computation parameters] D0245 UPR: Setpoint ramp-up rate [Computation parameters] D0246 DNR: Setpoint ramp-down rate [Computation parameters] D0250 ORB: ON/OFF rate detection band [Computation parameters] D0251 ORH: ON/OFF rate high-limit [Computation parameters] D0252 ORL: ON/OFF rate low-limit [Computation parameters] D0254 OH (Output high limit Heating-side output high limit (in heating/cooling control)) [Computation parameters] D0255 OL (Output low limit Cooling-side output high limit (in heating/cooling control)) [Computation parameters] D0256 HYS (Hysteresis) [Computation parameters] D0257 DR (Direct/reverse action switching) [Computation parameters] D0258 HB1 (Heater burnout current setpoint 1) [Computation parameters] D0259 HB2 (Heater burnout current setpoint 2) [Computation parameters] D0301 1.SP: Target setpoint [Group-1 parameters] D0306 1.P: Proportional band [Group-1 parameters] D0307 1.I: Integral time [Group-1 parameters] D0308 1.D: Derivative time [Group-1 parameters] D0311 1.MR: Manual reset [Group-1 parameters] D0314 1.Pc: Cooling-side proportional band [Group-1 parameters] D0315 1.Ic: Cooling-side integral time [Group-1 parameters] D0316 1.Dc: Cooling-side derivative time [Group-1 parameters] D0318 1.DB: Deadband [Group-1 parameters] D0319 1.RP: Zone PID reference point [Group-1 parameters] D0326 2.SP: Target setpoint [Group-2 parameters] D0331 2.P: Proportional band [Group-2 parameters] D0332 2.I: Integral time [Group-2 parameters] D0333 2.D: Derivative time [Group-2 parameters] D0336 2.MR: Manual reset [Group-2 parameters] D0339 2.Pc: Cooling-side proportional band [Group-2 parameters] D0340 2.Ic: Cooling-side integral time [Group-2 parameters] D0341 2.Dc: Cooling-side derivative time [Group-2 parameters] D0343 2.DB: Deadband [Group-2 parameters] D0344 2.RP: Zone PID reference point [Group-2 parameters] D0351 3.SP: Target setpoint [Group-3 parameters] D0356 3.P: Proportional band [Group-3 parameters] D0357 3.I: Integral time [Group-3 parameters] D0358 3.D: Derivative time [Group-3 parameters] D0361 3.MR: Manual reset [Group-3 parameters] D0364 3.Pc: Cooling-side proportional band [Group-3 parameters] D0365 3.Ic: Cooling-side integral time [Group-3 parameters] D0366 3.Dc: Cooling-side derivative time [Group-3 parameters] D0368 3.DB: Deadband [Group-3 parameters] D0376 4.SP: Target setpoint [Group-4 parameters] D0381 4.P: Proportional band [Group-4 parameters] D0382 4.I: Integral time [Group-4 parameters] D0383 4.D: Derivative time [Group-4 parameters] D0386 4.MR: Manual reset [Group-4 parameters] D0389 4.Pc: Cooling-side proportional band [Group-4 parameters] D0390 4.Ic: Cooling-side integral time [Group-4 parameters] D0391 4.Dc: Cooling-side derivative time [Group-4 parameters] D0393 4.DB: Deadband [Group-4 parameters] D0494 RDV: zone PID reference deviation. [PID switching parameter] D0904 TMU (Time unit for ramp-rate setting) [Time unit for ramp-rate setting] D0915 AL1 (Alarm-1 type) [Alarm setting parameters] D0916 AL2 (Alarm-2 type) [Alarm setting parameters] D0917 AL3 (Alarm-3 type) [Alarm setting parameters] D0919 HY1 (Alarm-1 hysteresis) [Alarm hysteresis] D0920 HY2 (Alarm-2 hysteresis) [Alarm hysteresis] D0921 HY3 (Alarm-3 hysteresis) [Alarm hysteresis] D0924 PO (Preset output/Heating-side B150 preset output (in heating/cooling control)) [Control function setting parameters] D0925 POc (Cooling-side preset output) [Control function setting parameters] D0927 C.MD (PID control mode) [Control function setting parameters] D0928 AR (Anti-reset windup (Excess integration prevention)) [Control function setting parameters] D0929 ZON (Zone PID selection) [Control function setting parameters] D0932 DIS (DI function selection) [Control function setting parameters] D0933 SPH (Upper limits of target setpoint) [Upper and lower limits of target setpoint] D0934 SPL (Lower limits of target setpoint) [Upper and lower limits of target setpoint] D0935 DY1 (Alarm-1 delay timer) [Alarm-ON delay time] D0936 DY2 (Alarm-2 delay timer) [Alarm-ON delay time] D0937 DY3 (Alarm-3 delay timer) [Alarm-ON delay time] D1013 RET (Retransmission output type) [Retransmission output setting parameters] D1014 RTH (Max. value of retransmission output scale) [Retransmission output setting parameters] D1015 RTL (Min. value of retransmission output scale) [Retransmission output setting parameters] D1036 LOCK [Menu-lock setting parameters] D1101 C.S1 (SELECT display-1registration) [SELECT display registration parameters] D1102 C.S2 (SELECT display-2 registration) [SELECT display registration parameters] D1103 C.S3 (SELECT display-3 registration) [SELECT display registration parameters] D1104 C.S4 (SELECT display-4 registration) [SELECT display registration parameters] D1201 IN (PV input type) [PV input parameters] D1202 UNI (PV input unit) [PV input parameters] D1204 RH (Max. value of PV input range) [PV input parameters] D1205 RL (PV input parameters) [PV input parameters] D1206 SDP (PV input parameters) [PV input parameters] D1207 SH (PV input parameters) [PV input parameters] D1208 SL (Min. value of PV input range) [PV input parameters] D1209 BSL (Selection of PV input burnout action) [PV input parameters] D1210 RJC (Presence/absence of PV input reference junction compensation) [PV input parameters] D1238 OT (Control output type) [Control output parameters] D1240 CT (Control output cycle time Heating-side control output cycle time (in heating/cooling control)) [Control output parameters] D1242 CTc (Cooling-side control output cycle time) [Control output parameters] D1247 PSL (Protocol selection) [RS-485 communication parameters] D1248 BPS (Baud rate) [RS-485 communication parameters] D1249 PRI (Parity) [RS-485 communication parameters] D1250 STP (Stop bit) [RS-485 communication parameters] D1251 DLN (Data length) [RS-485 communication parameters] D1252 ADR (Address) [RS-485 communication parameters] D1253 RP.T (Minimum response time) [RS-485 communication parameters] [D-SigDataEnd]-B [I-SigData] I0001 Input error (same as D0001) [Status] I0017 PV error (same as D0002) [Status] I0049 Error in calibration values or parameters (same as D0035) [Status] I0065 Mode (same as D0008) [Status] I0097 Alarm status (same as D0011) [Status] I0193 Input error (same as D0001) [ON-status] I0209 PV error (same as D0002) [ON-status] I0241 Error in calibration values or parameters (same as D0035) [ON-status] I0257 Mode (same as D0008) [ON-status] I0289 Alarm status (same as D0011) [ON-status] I0385 Input error (same as D0001) [OFF-status] I0401 PV error (same as D0002) [OFF-status] I0433 Error in calibration values or parameters (same as D0035) [OFF-status] I0449 Mode (same as D0008) [OFF-status] I0481 Alarm status (same as D0011) [OFF-status] [I-SigDataEnd] [I-SigData]-B I0001 ADERROR.st [Status] I0018 PVBO.st [Status] I0019 RJCERR.st [Status] I0021 PV+over.st [Status] I0022 PV-over.st [Status] I0031 AT.E.st [Status] I0049 CALB.E.st [Status] I0055 SETUP.st [Status] I0057 PARA.E.st [Status] I0061 EEP.E.st [Status] I0063 SYSTEM.E.st [Status] I0065 AUT/MAN.st [Status] I0067 S/R.st [Status] I0079 AT.st [Status] I0097 ALM1.st [Status] I0098 ALM2.st [Status] I0099 ALM3.st [Status] I0102 OR.st [Status] I0193 ADERROR.on [ON-status] I0210 PVBO.on [ON-status] I0211 RJCERR.on [ON-status] I0213 PV+over.on [ON-status] I0214 PV-over.on [ON-status] I0223 AT.E.on [ON-status] I0241 CALB.E.on [ON-status] I0247 SETUP.on [ON-status] I0249 PARA.E.on [ON-status] I0253 EEP.E.on [ON-status] I0255 SYSTEM.E.on [ON-status] I0257 AUT/MAN.on [ON-status] I0259 S/R.on [ON-status] I0271 AT.on [ON-status] I0289 ALM1.on [ON-status] I0290 ALM2.on [ON-status] I0291 ALM3.on [ON-status] I0294 OR.on [ON-status] I0385 ADERROR.off [OFF-status] I0402 PVBO.off [OFF-status] I0403 RJCERR.off [OFF-status] I0405 PV+over.off [OFF-status] I0406 PV-over.off [OFF-status] I0415 AT.E.off [OFF-status] I0433 CALB.E.off [OFF-status] I0439 SETUP.off [OFF-status] I0441 PARA.E.off [OFF-status] I0445 EEP.E.off [OFF-status] I0447 SYSTEM.E.off [OFF-status] I0449 AUT/MAN.off [OFF-status] I0451 S/R.off [OFF-status] I0463 AT.off [OFF-status] I0481 ALM1.off [OFF-status] I0482 ALM2.off [OFF-status] I0483 ALM3.off [OFF-status] I0486 OR.off [OFF-status] [I-SigDataEnd]-B