Name=PLC1 DCP31 MaxSigCnt=310 DataFormat=Decimal [SigData] 00501 Alarm status (1) 00501.0 AL01 Input 1 over-range 00501.1 AL02 Input 1 under-range 00501.6 AL07 Input 1 RTD disconnection A 00501.7 AL08 Input 1 RTD disconnection B 00501.8 AL09 Input 1 RTD disconnection C 00501.9 AL10 MFB disconnection 00501.A AL11 MFB short-circuit 00501.B AL12 MFB adjustment impossible 00502 Alarm status (2) 00502.0 AL70 A/DT malfunction 00502.5 Low battery voltage 00502.7 AL81 Board configuration error 00502.C AL96 Program error 00502.D AL97 Parameter error 00502.E AL98 Adjustment value error 00502.F AL99 PROM error 00503 Event output status 00503.0 Event 1 (EV1) 00503.1 Event 2 (EV2) 00503.2 Event 3 (EV3) 00503.3 Time event 1 (T1) 00503.6 Time event 2 (T2) 00503.7 Time event 3 (T3) 00503.8 Time event 4 (T4) 00503.9 Time event 5 (T5) 00504 PV1 00505 SP1 00508 Status (1)/Run operation (1) 00509 Segment No. 00510 Program No. 00511 MV1 00513 Status (2)/Run operation (2) 00515 Segment progress time 00516 Run progress time 00517 Using PID group No. (CH1) 00519 Cycle execution count 00523 Heat MV 00524 Cool MV 00525 Motor feedback value 00526 External switch input status 00526.0 RSW1 (RUN) 00526.1 RSW2 (HOLD) 00526.2 RSW3 (RESET) 00526.3 RSW4 (ADV) 00526.4 RSW5 00526.5 RSW6 00526.6 RSW7 00526.7 RSW8 (Program selection weighting 1) 00526.8 RSW9 (Program selection weighting 2) 00526.9 RSW10 (Program selection weighting 4) 00526.A RSW11 (Program selection weighting 8) 00526.B RSW12 (Program selection weighting 10) 01001 Operation mode 01002 SP1 01004 Event 1 setting value 01005 Event 2 setting value 01006 Event 3 setting value 01011 Proportional band (CH1) 01012 Reset time (CH1) 01013 Rate time (CH1) 01014 MV lower limit (CH1) 01015 MV upper limit (CH1) 01016 Manual reset (CH1) 01017 Brake (CH1) 01018 Disturbance inhibit proportional band (CH1) 01019 Disturbance inhibit reset time (CH1) 01020 Disturbance inhibit rate time (CH1) 01021 Proportional band (for CH1 cool control) 01022 Reset time (for CH1 cool control) 01023 Rate time (for CH1 cool control) 01024 MV lower limit (for CH1 cool control) 01025 MV upper limit (for CH1 cool control) 01026 Manual reset (for CH1 cool control) 01501 Proportional band (PID set 1-1) 01502 Reset time (PID set 1-1) 01503 Rate time (PID set 1-1) 01504 MV lower limit (PID set 1-1) 01505 MV upper limit (PID set 1-1) 01506 Manual reset (PID set 1-1) 01507 Brake (PID set 1-1) 01508 Disturbance inhibit proportional band (PID set 1-1) 01509 Disturbance inhibit reset time (PID set 1-1) 01510 Disturbance inhibit rate time (PID set 1-1) 01511 Proportional band (PID set 1-2) 01512 Reset time (PID set 1-2) 01513 Rate time (PID set 1-2) 01514 MV lower limit (PID set 1-2) 01515 MV upper limit (PID set 1-2) 01516 Manual reset (PID set 1-2) 01517 Brake (PID set 1-2) 01518 Disturbance inhibit proportional band (PID set 1-2) 01519 Disturbance inhibit reset time (PID set 1-2) 01520 Disturbance inhibit rate time (PID set 1-2) 01521 Proportional band (PID set 1-3) 01522 Reset time (PID set 1-3) 01523 Rate time (PID set 1-3) 01524 MV lower limit (PID set 1-3) 01525 MV upper limit (PID set 1-3) 01526 Manual reset (PID set 1-3) 01527 Brake (PID set 1-3) 01528 Disturbance inhibit proportional band (PID set 1-3) 01529 Disturbance inhibit reset time (PID set 1-3) 01530 Disturbance inhibit rate time (PID set 1-3) 01531 Proportional band (PID set 1-4) 01532 Reset time (PID set 1-4) 01533 Rate time (PID set 1-4) 01534 MV lower limit (PID set 1-4) 01535 MV upper limit (PID set 1-4) 01536 Manual reset (PID set 1-4) 01537 Brake (PID set 1-4) 01538 Disturbance inhibit proportional band (PID set 1-4) 01539 Disturbance inhibit reset time (PID set 1-4) 01540 Disturbance inhibit rate time (PID set 1-4) 01541 Proportional band (PID set 1-5) 01542 Reset time (PID set 1-5) 01543 Rate time (PID set 1-5) 01544 MV lower limit (PID set 1-5) 01545 MV upper limit (PID set 1-5) 01546 Manual reset (PID set 1-5) 01547 Brake (PID set 1-5) 01548 Disturbance inhibit proportional band (PID set 1-5) 01549 Disturbance inhibit reset time (PID set 1-5) 01550 Disturbance inhibit rate time (PID set 1-5) 01551 Proportional band (PID set 1-6) 01552 Reset time (PID set 1-6) 01553 Rate time (PID set 1-6) 01554 MV lower limit (PID set 1-6) 01555 MV upper limit (PID set 1-6) 01556 Manual reset (PID set 1-6) 01557 Brake (PID set 1-6) 01558 Disturbance inhibit proportional band (PID set 1-6) 01559 Disturbance inhibit reset time (PID set 1-6) 01560 Disturbance inhibit rate time (PID set 1-6) 01561 Proportional band (PID set 1-7) 01562 Reset time (PID set 1-7) 01563 Rate time (PID set 1-7) 01564 MV lower limit (PID set 1-7) 01565 MV upper limit (PID set 1-7) 01566 Manual reset (PID set 1-7) 01567 Brake (PID set 1-7) 01568 Disturbance inhibit proportional band (PID set 1-7) 01569 Disturbance inhibit reset time (PID set 1-7) 01570 Disturbance inhibit rate time (PID set 1-7) 01571 Proportional band (PID set 1-8) 01572 Reset time (PID set 1-8) 01573 Rate time (PID set 1-8) 01574 MV lower limit (PID set 1-8) 01575 MV upper limit (PID set 1-8) 01576 Manual reset (PID set 1-8) 01577 Brake (PID set 1-8) 01578 Disturbance inhibit proportional band (PID set 1-8) 01579 Disturbance inhibit reset time (PID set 1-8) 01580 Disturbance inhibit rate time (PID set 1-8) 02501 Key lock 02502 Program protect 02503 Input 1 digital filter 02504 Input 1 bias 02505 SP1 bias 02506 MV change limitter (CH1) 02507 PID operation initial MV (CH1) 02508 Pid operation initialization 02509 Auto-tuning method selection (CH1) 02510 Smart-tuning method selection (CH1) 02511 Advanced PID selection (CH1) 02512 G.Soak time (CH1) 02513 PID auto-switching point 1-1 02514 PID auto-switching point 1-2 02515 PID auto-switching point 1-3 02516 PID auto-switching point 1-4 02517 PID auto-switching point 1-5 02518 PID auto-switching point 1-6 02519 PID auto-switching point 1-7 02520 FAST factor 02521 ON-OFF control differential / Position-proportional dead zone / Heat/cool control dead zone 02522 Output 1 time-proportional output cycle 02523 Output 2 time-proportional output cycle 02524 Output 3 time-proportional output cycle 02525 3-position control deviation lower limit 02526 3-position control deviation upper limit 02527 3-position control lower limit hysteresis 02528 3-position control upper limit hysteresis 02529 Motor control method selection 02530 Motor valve opening automatic adjustment 02531 Motor valve opening adjustment fully closed position 02532 Motor valve opening adjustment fully open position 02533 Motor valve opening adjustment fully open/closed time 03501 Event 1 type 03502 Event 1 standby 03503 Event 1 hysteresis 03504 Event 1 ON delay time 03505 Event 2 type 03506 Event 2 standby 03507 Event 2 hysteresis 03508 Event 2 ON delay time 03509 Event 3 type 03510 Event 3 standby 03511 Event 3 hysteresis 03512 Event 3 ON delay time 03513 Time event type 03514 T1 event type 03515 T1 event standby 03516 T1 event hysteresis 03517 T1 event ON delay 03518 T2 event type 03519 T2 event standby 03520 T2 event hysteresis 03521 T2 event ON delay time 03522 T3 event type 03523 T3 event standby 03524 T3 event hysteresis 03525 T3 event ON delay time 03526 T4 event type 03527 T4 event standby 03528 T4 event hysteresis 03529 T4 event ON delay time 03530 T5 event type 03531 T5 event standby 03532 T5 event hysteresis 03533 T5 event ON delay time 04001 Input linearization table approximation A1 04002 Input linearization table approximation A2 04003 Input linearization table approximation A3 04004 Input linearization table approximation A4 04005 Input linearization table approximation A5 04006 Input linearization table approximation A6 04007 Input linearization table approximation A7 04008 Input linearization table approximation A8 04009 Input linearization table approximation A9 04010 Input linearization table approximation A10 04011 Input linearization table approximation A11 04012 Input linearization table approximation B1 04013 Input linearization table approximation B2 04014 Input linearization table approximation B3 04015 Input linearization table approximation B4 04016 Input linearization table approximation B5 04017 Input linearization table approximation B6 04018 Input linearization table approximation B7 04019 Input linearization table approximation B8 04020 Input linearization table approximation B9 04021 Input linearization table approximation B10 04022 Input linearization table approximation B11 04501 Control action (CH1) 04502 Input 1 temperature unit 04503 Input 1 range type 04504 Input 1 range decimal point position 04505 Input 1 range lower limit (0%) 04506 Input 1 range upper limit (100%) 04507 Input 1 root extraction dropout 04508 Input 1 linearization table approximation 04509 SP1 lower limit 04510 SP1 upper limit 04511 PID set auto-switching (CH1) 04512 MV setting at input 1 over-range (MV1) 04513 Preset manual value (MV1) 04514 Manual change mode (MV1) 04515 Preset manual value (MV1) 04516 MV in READY mode (MV1, MV1 heat output) 04517 MV (cool) in READY mode (MV1 cool output) 04518 Main output type (CH1) 04519 SP1 main output lower limit (4mA setting) 04520 SP1 main output upper limit (20mA setting) 04545 With/without 3-position control 04546 Auxiliary output 1 type 04547 Auxiliary output 1 lower limit (4mA) 04548 Auxiliary output 1 upper limit (20mA) 04549 Auxiliary output 2 type 04550 Auxiliary output 2 lower limit (4mA) 04551 Auxiliary output 2 upper limit (20mA) 04552 External switch input RSW5 assignment 04553 External switch input RSW6 assignment 04554 External switch input RSW7 assignment 04555 Para key assignment item 1 04556 Para key assignment item 2 04557 Para key assignment item 3 04558 Para key assignment item 4 04559 Para key assignment item 5 04560 Para key assignment item 6 04561 Para key assignment item 7 04562 Para key assignment item 8 04563 Operation completion state 04564 Program time unit 04565 Time display 04566 PV display 04567 Alarm display 04568 Programming item: Events 1 to 3 04569 Programming item: Time events 1 to 5 04570 Programming item: PID set, G.SOAK 04571 Programming item: PV start, cycle,pattern link 04572 Cold junction compensation 04573 Input operation at input 1 disconnection 04574 Voltage time-proportional output system 04575 Output 1 selection 04576 Output 2 selection 04578 Voltage output 1 adjustment 04579 Voltage output 2 adjustment 04581 Input 1 burnout current (expansion setting 1) 04582 Expansion setting 2 04584 CPL communication address 04585 CPL communication speed/code 04590 Special function 04591 Input 1 zener barrier adjustment 04592 Input 2 zener barrier adjustment 04593 CPL communication port selection 04594 PID type 04596 Hardware type 1 04597 Hardware type 2 04598 ROM ID 04599 ROM item 04600 ROM revision [SigDataEnd]