Name=PLC1 SDC3031 MaxSigCnt=379 DataFormat=Hex [SigData] 00501 Alarm status 00501.1 AL07 T wire disconnection, or FB wire input error 00501.2 AL03 C wire or CJ wire input error 00501.4 AL01 PV input overrange 00501.5 AL02 PV input underrange 00501.6 AL05 RSP overrange (indicated only with remote SP) 00501.7 AL06 RSP underrange (occurs only with remote SP) 00501.9 AL08 Motor adjustment error (position proportional model) 00501.B ALxx Alarm occurrence 00501.C AL96 Parameter error (communication RAM area) 00501.D AL91 Illegal loader communication message 00501.E AL97 Parameter error (check sum) 00501.F AL98 Adjustment data error (check sum) 00502 Event status 00502.1 EV1 Event 1 status 00502.2 EV2 Event 2 status 00502.4 RSW1 Remote switch input 1 status 00502.5 RSW2 Remote switch input 2 status 00502.6 RSW3 Remote switch input 3 status 00502.7 RSW4 Remote switch input 4 status 00503 Control action status 00503.0 PID 0:PID control, 1:ON/OFF control 00503.1 Al 0:Learning stop status, 1:During learning (over-shoot control function) 00503.2 NFB 0:A motor feedback value is in use, 1:A motor feedback presumed value is in use 00503.4 CLOSE Close relay ON (position proportional model) 00503.5 OPEN Open relay ON (position proportional model) 00504 SP Group No. in use 00505 SP value in use 00506 PV(Process Variable) 00507 MV(Manipulated Variable) 00508 Motor feedback value(%) 00509 PID group in use 00510 Mode action status 00510.0 AUTO 00510.1 MANUAL 00510.4 RUN 00510.5 READY 00510.8 LOCAL 00510.9 REMOTE 00510.C AT stop 00510.D AT start 01001 Set point SP0 01002 Set point SP1 01003 Set point SP2 01004 Set point SP3 01005 Set point SP4 01006 Set point SP5 01007 Set point SP6 01008 Set point SP7 01501 Event 1 set value 01502 Event 2 set value 02001 Proportional band P 0 02002 Integral time I 0 02003 Derivative time D 0 02004 Munipulated variable low limit OL 0 02005 Operation use high limit OH 0 02006 Manual reset RE 0 02007 Differential DIF 0 02008 Proportional band P 1 02009 Integral time I 1 02010 Derivative time D 1 02011 Munipulated variable low limit OL 1 02012 Operation use high limit OH 1 02013 Manual reset RE 1 02014 Differential DIF 1 02015 Proportional band P 2 02016 Integral time I 2 02017 Derivative time D 2 02018 Munipulated variable low limit OL 2 02019 Operation use high limit OH 2 02020 Manual reset RE 2 02021 Differential DIF 2 02022 Proportional band P 3 02023 Integral time I 3 02024 Derivative time D 3 02025 Munipulated variable low limit OL 3 02026 Operation use high limit OH 3 02027 Manual reset RE 3 02028 Differential DIF 3 02029 Proportional band P 4 02030 Integral time I 4 02031 Derivative time D 4 02032 Munipulated variable low limit OL 4 02033 Operation use high limit OH 4 02034 Manual reset RE 4 02035 Differential DIF 4 02036 Proportional band P 5 02037 Integral time I 5 02038 Derivative time D 5 02039 Munipulated variable low limit OL 5 02040 Operation use high limit OH 5 02041 Manual reset RE 5 02042 Differential DIF 5 02043 Proportional band P 6 02044 Integral time I 6 02045 Derivative time D 6 02046 Munipulated variable low limit OL 6 02047 Operation use high limit OH 6 02048 Manual reset RE 6 02049 Differential DIF 6 02050 Proportional band P 7 02051 Integral time I 7 02052 Derivative time D 7 02053 Munipulated variable low limit OL 7 02054 Operation use high limit OH 7 02055 Manual reset RE 7 02056 Differential DIF 7 02057 Proportional band P r 02058 Integral time I r 02059 Derivative time D r 02060 Munipulated variable low limit OL r 02061 Operation use high limit OH r 02062 Manual reset RE r 02063 Differential DIF r 02064 Proportional band dP 0 02065 Integral time dI 0 02066 Derivative time dd 0 02067 Proportional band dP 1 02068 Integral time dI 1 02069 Derivative time dd 1 02070 Proportional band dP 2 02071 Integral time dI 2 02072 Derivative time dd 2 02073 Proportional band dP 3 02074 Integral time dI 3 02075 Derivative time dd 3 02076 Proportional band dP 4 02077 Integral time dI 4 02078 Derivative time dd 4 02079 Proportional band dP 5 02080 Integral time dI 5 02081 Derivative time dd 5 02082 Proportional band dP 6 02083 Integral time dI 6 02084 Derivative time dd 6 02085 Proportional band dP 7 02086 Integral time dI 7 02087 Derivative time dd 7 02088 Proportional band dP r 02089 Integral time dI r 02090 Derivative time dd r 02501 Event 1 hysteresis 02502 Event 1 on delay 02503 Event 2 hysteresis 02504 Event 2 on delay 02505 PV filter 02506 PV bias 02507 RSP bias 02508 Output cycle 02509 Manipulated variable change limit 02510 Zone setting (Zn 0) 02511 Zone setting (Zn 1) 02512 Zone setting (Zn 2) 02513 Zone setting (Zn 3) 02514 Zone setting (Zn 4) 02515 Zone setting (Zn 5) 02516 Zone setting (Zn 6) 02517 Zone setting (Zn 7) 02527 SP ramp up gradient 02528 SP ramp down gradient 03001 Selection of key lock status 03002 Selection of temperature unit 03003 Selection of control action 03004 Selection of input range type 03005 Selection of decimal point position 03006 Setting of PV range low limit 03007 Setting of PV range high limit 03008 Selection of SP setting system 03009 Setting of low limit of SP limit 03010 Setting of high limit of SP limit 03011 Selection of manipulated variable at input error 03012 Setting of manipulated variable in READY mode or at PV input error 03013 Selection of manual output 03014 Setting of preset manual value 03015 Setting of PID operation initial manipulated variable 03016 Selection of PID operation initialize 03017 Selection of zone PID action 03018 Selection of control system 03019 Selection of disturbance suppression function action 03020 Selection of neural network auto tuning action 03021 Selection of event 1 action type 03022 Selection of event 1 stand-by action 03023 Selection of event 2 action type 03024 Selection of event 2 stand-by action 03025 Selection of event action in READY mode 03026 Setting of the number of LSPs whick can be set by remote switch input 03027 Selection of remote switch input 1 function 03028 Selection of remote switch input 2 function 03029 Selection of remote switch input 3 function 03030 Selection of remote switch input 4 function 03031 Communication address 03032 Transmission speed 03033 Data format 03034 Setting of dead zone 03035 Selection of M/M control 03036 Automatic M/M adjusment start 03037 Setting of M/M adjustment value(fully close) 03038 Setting of M/M adjustment value(fully open) 03039 Setting of M/M fully close/fully open time 03040 Setting of SP ramp up gradient 03041 Setting of SP ramp down gradient 03042 Sellection of SP ramp time unit 03043 Setting of green belt range 03044 Selection of auxiliary output type 03045 Setting of auxiliary output 4mA 03046 Setting of auxiliary output 20mA 03047 Setting of RSP 0% (4mA,1V) 03048 Setting of RSP 100% (20mA,5V) 03049 Selection of cold junction compensation action 03504 SP Group No. in use 03505 SP value in use 03510 Mode action status 04001 Set point SP0 04002 Set point SP1 04003 Set point SP2 04004 Set point SP3 04005 Set point SP4 04006 Set point SP5 04007 Set point SP6 04008 Set point SP7 04501 Event 1 set value 04502 Event 2 set value 05001 Proportional band P 0 05002 Integral time I 05003 Derivative time D 0 05004 Munipulated variable low limit OL 0 05005 Operation use high limit OH 0 05006 Manual reset RE 0 05007 Differential DIF 0 05008 Proportional band P 1 05009 Integral time I 1 05010 Derivative time D 1 05011 Munipulated variable low limit OL 1 05012 Operation use high limit OH 1 05013 Manual reset RE 1 05014 Differential DIF 1 05015 Proportional band P 2 05016 Integral time I 2 05017 Derivative time D 2 05018 Munipulated variable low limit OL 2 05019 Operation use high limit OH 2 05020 Manual reset RE 2 05021 Differential DIF 2 05022 Proportional band P 3 05023 Integral time I 3 05024 Derivative time D 3 05025 Munipulated variable low limit OL 3 05026 Operation use high limit OH 3 05027 Manual reset RE 3 05028 Differential DIF 3 05029 Proportional band P 4 05030 Integral time I 4 05031 Derivative time D 4 05032 Munipulated variable low limit OL 4 05033 Operation use high limit OH 4 05034 Manual reset RE 4 05035 Differential DIF 4 05036 Proportional band P 5 05037 Integral time I 5 05038 Derivative time D 5 05039 Munipulated variable low limit OL 5 05040 Operation use high limit OH 5 05041 Manual reset RE 5 05042 Differential DIF 5 05043 Proportional band P 6 05044 Integral time I 6 05045 Derivative time D 6 05046 Munipulated variable low limit OL 6 05047 Operation use high limit OH 6 05048 Manual reset RE 6 05049 Differential DIF 6 05050 Proportional band P 7 05051 Integral time I 7 05052 Derivative time D 7 05053 Munipulated variable low limit OL 7 05054 Operation use high limit OH 7 05055 Manual reset RE 7 05056 Differential DIF 7 05057 Proportional band P r 05058 Integral time I r 05059 Derivative time D r 05060 Munipulated variable low limit OL r 05061 Operation use high limit OH r 05062 Manual reset RE r 05063 Differential DIF r 05064 Proportional band dP 0 05065 Integral time dI 0 05066 Derivative time dd 0 05067 Proportional band dP 1 05068 Integral time dI 1 05069 Derivative time dd 1 05070 Proportional band dP 2 05071 Integral time dI 2 05072 Derivative time dd 2 05073 Proportional band dP 3 05074 Integral time dI 3 05075 Derivative time dd 3 05076 Proportional band dP 4 05077 Integral time dI 4 05078 Derivative time dd 4 05079 Proportional band dP 5 05080 Integral time dI 5 05081 Derivative time dd 5 05082 Proportional band dP 6 05083 Integral time dI 6 05084 Derivative time dd 6 05085 Proportional band dP 7 05086 Integral time dI 7 05087 Derivative time dd 7 05088 Proportional band dP r 05089 Integral time dI r 05090 Derivative time dd r 05501 Event 1 hysteresis 05502 Event 1 on delay 05503 Event 2 hysteresis 05504 Event 2 on delay 05505 PV filter 05506 PV bias 05507 RSP bias 05508 Output cycle 05509 Manipulated variable change limit 05510 Zone setting (Zn 0) 05511 Zone setting (Zn 1) 05512 Zone setting (Zn 2) 05513 Zone setting (Zn 3) 05514 Zone setting (Zn 4) 05515 Zone setting (Zn 5) 05516 Zone setting (Zn 6) 05517 Zone setting (Zn 7) 05527 SP ramp up gradient 05528 SP ramp down gradient 06001 Selection of key lock status 06002 Selection of temperature unit 06003 Selection of control action 06004 Selection of input range type 06005 Selection of decimal point position 06006 Setting of PV range low limit 06007 Setting of PV range high limit 06008 Selection of SP setting system 06009 Setting of low limit of SP limit 06010 Setting of high limit of SP limit 06011 Selection of manipulated variable at input error 06012 Setting of manipulated variable in READY mode or at PV input error 06013 Selection of manual output 06014 Setting of preset manual value 06015 Setting of PID operation initial manipulated variable 06016 Selection of PID operation initialize 06017 Selection of zone PID action 06018 Selection of control system 06019 Selection of disturbance suppression function action 06020 Selection of neural network auto tuning action 06021 Selection of event 1 action type 06022 Selection of event 1 stand-by action 06023 Selection of event 2 action type 06024 Selection of event 2 stand-by action 06025 Selection of event action in READY mode 06026 Setting of the number of LSPs whick can be set by remote switch input 06027 Selection of remote switch input 1 function 06028 Selection of remote switch input 2 function 06029 Selection of remote switch input 3 function 06030 Selection of remote switch input 4 function 06031 Communication address 06032 Transmission speed 06033 Data format 06034 Setting of dead zone 06035 Selection of M/M control 06037 Setting of M/M adjustment value(fully close) 06038 Setting of M/M adjustment value(fully open) 06039 Setting of M/M fully close/fully open time 06040 Setting of SP ramp up gradient 06041 Setting of SP ramp down gradient 06042 Sellection of SP ramp time unit 06043 Setting of green belt range 06044 Selection of auxiliary output type 06045 Setting of auxiliary output 4mA 06046 Setting of auxiliary output 20mA 06047 Setting of RSP 0% (4mA,1V) 06048 Setting of RSP 100% (20mA,5V) 06049 Selection of cold junction compensation action [SigDataEnd]